Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable second adapter on LifeView TV Walker Twin DVB-T USB2.0
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Make sure devices manufactured by Dposh are not affected by previous hw 
pid filtering changes

Doing so might crash it.
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Spotted by Jeremy Nysen.
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add support for Satelco EasyWatch PCI DVB-S card (subsystem 0x1894:0x001b).
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enhance the dvb-pll definition of the fmd1216 tuner by adding an init sequence
and a sleep sequence.

The init sequence sets the AGC control register to 0xa0, selecting the fast
time constant and 112 dBuV take-over point.  This the recommended value for
DVB-T operation.

The sleep sequence sets bit P4 (which is believed to turn the analog
demodulator on), turns off the tuning voltage, and sets the AGC control
register to 0x60 (external AGC voltage, the recommended value for analog
operation).

The existing dvb-pll users in the cx88 driver, listed below, will gain these
init and sleep sequences.

CX88_BOARD_HAUPPAUGE_HVR1100    Hauppauge WinTV-HVR1100 DVB-T/Hybrid
CX88_BOARD_HAUPPAUGE_HVR1100LP  Hauppauge WinTV-HVR1100 DVB-T/Hybrid (Low Profi
CX88_BOARD_WINFAST_DTV2000H     WinFast DTV2000 H
CX88_BOARD_HAUPPAUGE_HVR3000    Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DV
CX88_BOARD_HAUPPAUGE_HVR1300    Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encod

This non-dvb-pll user in the cx88 driver should only gain the sleep sequence,
as it already had an equivalent init sequence.  The non-dvb-pll code for this
user is removed.

X88_BOARD_DNTV_LIVE_DVB_T_PRO   digitalnow DNTV Live! DVB-T Pro

In these saa7134 driver, these non-dvb-pll users are converted to use dvb-pll:

SAA7134_BOARD_MD7134                    Medion 7134
SAA7134_BOARD_ASUS_EUROPA2_HYBRID       Asus Europa2 OEM

The saa7134 functions philips_fmd1216_tuner_init(),
philips_fmd1216_tuner_sleep(), and philips_fmd1216_tuner_set_params() are
deleted and the dvb-pll versions are used.

This should result in equivalent sleep, init, and tuning sequences being sent
to the tuner.

For the cxusb driver, only one board is effected:

USB_PID_MEDION_MD95700          	Medion MD95700

This board used dvb_usb_tuner_init_i2c() and dvb_usb_tuner_set_params_i2c()
for init and tuning, respectively.  These functions are effectively the same
as the dvb-pll versions.  They call a tuner pass control function defined at
the dvb-usb level, but this does not matter, as this card does not have a
tuner pass control function (only the dib3000mb does).  This board will gain
the sleep sequence, while init and tuning should be unchanged.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Support for A-LINK DTU(m) is not included in this patch.
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Acked-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Marked af9005 driver as experimental and add dependency for qt1010;
Added a dependency on qt1010 in Kconfig;
Corrected the experimental gain  reduction of the mt2060 in case of
strong signal (though it is code included in #ifdef 0).
Signed-off-by: NLuca Olivetti <luca@ventoso.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NLuca Olivetti <luca@ventoso.org>
Signed-off-by: NManu Abraham <abraham.manu@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

convert calls to dib3000mb_attach to use dvb_attach
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

moved tda665x pll_init into dvb_pll_desc dvb_pll_tda665x.initdata
convert handling of tda665x and tua6010xs to properly use dvb-pll
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

These sources do not need to #include "dvb-pll.h"
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

removed philips_sd1878_tda8261_tuner_set_params, using dvb_pll_attach, instead.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch removes duplicate code from cx88-dvb and saa7134-dvb that handles
rf input switching for the TUV1236d tuner.

The functionality is added to dvb-pll, where all the other code that 
handles the TUV1236d is kept.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Rename dvb_pll_desc.setbw() to set(), and accept struct dvb_frontend_parameters
instead of passing both freq and bandwidth, so that this may be used as a
generic function.

In order to do this, dvb_pll_configure must also be altered in the same manner,
to take struct dvb_frontend_parameters instead of freq and bandwidth.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

All the printks had missing level prefixes so I've fixed these too.
Also fixed some grammer errors.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves.  This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.

It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.

The patch causes all kernel threads to be nonfreezable by default (ie.  to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE.  It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear.  Additionally, it updates documentation to
describe the freezing of tasks more accurately.

[akpm@linux-foundation.org: build fixes]
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NNigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

if the call to budget_register() fails in ttpci_budget_int(),
ttpci_budget_init() returns success. The attached patch will
fix this problem.
Signed-off-by: NHartmut Birr <e9hack@googlemail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Spotted and tested by Thomas Sattler <tsattler@gmx.de>.

cinergyT2.c does cancel_delayed_work() + flush_scheduled_work() while
holding cinergyt2->sem. This leads to deadlock because work->func()
needs the same mutex to complete. Another bug is that this code in fact
can't reliably stop the re-arming delayed_work.

Convert this code to use cancel_rearming_delayed_work() and move it
out of ->sem. Another mutex, ->wq_sem, was added to protect against the
concurrent open/resume.

This patch is a horrible hack to fix the lockup which happens in practice.
As Dmitry Torokhov pointed out this driver has other problems and needs
further changes.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If one has a dependency chain (tristate)FOO depends on (bool)BAR depends on
(tristate)BAZ, build problems will result.  If BAZ=m, then BAR can be set
y, which allows FOO=y.  It's possible to have FOO=y && BAZ=m, which
wouldn't be allowed if FOO depended directly on BAZ.  In effect, the bool
promotes the tristate from m to y.

This ends up causing a problem with several menuconfigs that look like:

menuconfig BAR
	bool
	depends on BAZ [tristate]
if BAR
config FOO
	tristate
endif

The solution used here is to add the dependencies of BAR to the if
statement, so that items in the if block will gain a direct
non-bool-promoted dependency on BAZ.  This is how it would work if a menu
was used instead of an if block.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Acked-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: NJeff Garzik <jeff@garzik.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch moves flexcop-dma (currently used only by flexcop-pci) to
b2c2-flexcop-pci module, that is dependent on CONFIG_PCI, fixing the bug 
as reported by Geert Uytterhoeven <geert@linux-m68k.org>:

drivers/media/dvb/b2c2/flexcop-dma.c uses the PCI DMA API, but
DVB_B2C2_FLEXCOP doesn't depend on PCI, causing the following problem on
PCI-less systems:

| linux/drivers/media/dvb/b2c2/flexcop-dma.c:20: warning: implicit declaration of function 'pci_alloc_consistent'
| linux/drivers/media/dvb/b2c2/flexcop-dma.c:20: warning: implicit declaration of function 'pci_alloc_consistent'

Apparently this is the flexcop DMA core, which is used by both
DVB_B2C2_FLEXCOP_PCI and DVB_B2C2_FLEXCOP_USB.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Several people reported unreliable reception with the current driver.
Furthermore, STR and SNR values seem to be inverted.
This fix is based on a patch posted by Hartmut Hackman.
Thanks to Helmut Auer for testing and helping to optimize the patch.
tda826x:
- set baseband cut-off to 19 MHz
tda10086:
- change the parameters of the carrier recovery loop
- toggle register 0x02 between 0x35 (tuning) and 0x00 (locked)
- invert STR and SNR values
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If this mutex_lock_interruptible() does fail due to signal_pending() then the
state of the driver will get trashed in interesting ways, because userspace
cannot and will not retry the close().
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

dvb-core is not started early enough when device drivers that use dvb are
compiled in so dvb_register_device fails (silently) since dvb_class is
NULL, this runs dvb_init using subsys_initcall instead of module_init.

dvb_register_device will now check the return value of class_device_create.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

replace "streaming_crtl" with "streaming_ctrl"
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Disable second adapter on LifeView TV Walker Twin while it doesn't work 
properly.
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NNick Andrew <nick@nick-andrew.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Do not follow 80-col limit where it would cause inconsistency.
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

deb_rc is used by the dvb-usb core framework.  This patch replaces all
occurances of deb_rc with deb, in m920x.c, so that its clear that we're
not using dvb-usb's deb_rc.
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Some of the devices supported by the m920x driver have identical functions used
for tuner_attach and frontend_attach.  This patch consolidates the functions in
question, and updates the debug code to be generic for each.  This patch
decreases the size of the kernel.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Group the tuner configurations together.
- Group the demod configurations together.
- Group the device-specific initialization functions together.
- Group demod_attach functions together.
- Group tuner_attach functions together.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- 80-column cleanups
- spaces between operators
- tabbing style
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

These devices are sold by various companies and chains not involved in
hardware manufacturing business. This particular device owned by
winisch (from irc) had a sticker with text "TCM 234292" on it. This device
was never opened so it is possible that Dposh did not manufacture this
stick. However, the bundled software and their product line points into
that direction. Also thanks to Michael Krufky for spotting this hw
filtering problem and thus avoiding hair loss.
Hardware pid filters and the bundled remote controller are not currently
supported on this device.
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add support for "LifeView TV Walker Twin" (USB IDs 10fd:0513, 10fd:0514)
Signed-off-by: NNick Andrew <nick@nick-andrew.net>
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Uncomments code in vp702x-fe.c to enable DiSEqC in vp7021a
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NPat Erley <pat@erley.org>
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>