Upgrade the upstream driver from 2.0.0.0 to 2.1.2.1.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When IO is completed with underrun and with good SCSI status, check if
the transferred bytes against scsi_cmnd->underflow, which is set to
minimum number of bytes that must be transferred for this command, if
is less than required minimum, complete the IO with DID_ERROR.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

MS module did not invoke fdmi offline in all cases,
call fdmi offline when ms module receives a port offline,
so that fdmi offline is from one place in the ms module.

Make changes to handle 10G speed in the conversion routine.

Replaced the usage of bfa_adapter_attr_s struct with specific API's.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Modified the portstats get/clear logic for port physical/FCoE/QoS stats.
Added more stats to FC
Fixed some issues with FCoE stats collection.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

bfa_ioc_attr_s is a big structure and some times could cause
stack overflow if defined locally, so add specific APIs that
are needed to replace the use of ioc_attr local var.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Rename pport structures to fcport in BFA FCS, to resolve confusion
about the port structures in the firmware, and make sure the SG page
is setup correctly.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Currently BFA was not checking for IOC down condition when issuing
getstats/clearstats

Add check to see if IOC is operational, before issuing
getstats/clearstats.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Use dummy interrupt handlers till chip initialization is complete.
Install real interrupt handlers after chip initialization.

Also removed msix installation code in bfa_iocfc_init().
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fixed the issue of not acknowledging the command queue
full-to-non-full interrupt.  Implemented separate acknowledging
functions for different ASIC and interrupt mode.

Fixed the case of missing CPE interrupt by always processing the
pending requests in the completion path.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

ioc_recover failed to work in fcmode.

Fixed the code to initialize the ioc_regs.err_set during the
notify_hbfail.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Replace enum types with int and rearrange the fields to fix some
alignment issue.

Local var ioc_attr is causing the stack to overflow, so removed the
usage of the local ioc_attr var and now invoking an API to return the
ioc_type.

Fix some AEN issues.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Introduce a link notification state machine to handle next incoming
link events while the current event is being delivered to the driver.

When the event has been processed by the driver, the link notification
state machine will queue the next event (if there is any) to the
driver.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Made FCS authentication related changes to state machines and header
files.

Made changes in FCS state machines to handle the case when secret
string is NULL.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Changed PCI VPD to incorporate specific OEM vendors.

Added FCoE specific interrupt latency and delay params.

Added some variables needed by FIP 2.0.

Added some new logging and tracing definitions.

Added reserved members to make the structures (IOC, IOCFC) 64bit aligned.

Changed the module identifiers, as some files were moved.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Copy fpma MAC when requested by user space application.  Added FPMA
mac address to the lport attributes structure.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Make sure that in direct attach mode, we do not query the name server
after a target is marked offline.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Replace bfa_assert() with bfa_sm_fault() to get unhandled events for
debugging.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Clear LL_HALT and PSS_ERR bit in the interrupt status register on an IOC crash.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add support for faster IOC recovery after failure.

Split bfa_ioc.c into three files:
  bfa_ioc.c:    Common code shared between crossbow and catapult ASIC's.

  bfa_ioc_cb.c: Code specific to the crossbow, reg mapping and
                interrupt related routines.

  bfa_ioc_ct.c: Code specific to the catapult, reg mapping and
                interrupt related routines.

Fix to make sure IOC reinitialize's properly on enable request -
update the ioc_fwstate reg with BFI_IOC_FAIL on ioc disable mbox cmd
timeout.

Makefile changes to support the 2 newly added files bfa_ioc_cb.c and
bfa_ioc_ct.c.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

bfad.c & bfad_drv.h:
  * Created a kernel thread from pci_probe that does the bfad start
    operations after BFA init done on a firmware mismatch.
  * The kernel thread on a fw mismatch waits for an event from IOC
    call back and is woken up from bfa_cb_init() on BFA init success.
  * In normal cases of no firmware mismatch this thread is terminated
    in pci_probe.

bfa_fcs_lport.c, fabric.c, fcs_lport.h & vport.c:
  * Split the lport init to attach time and init time code, so that
    proper config attributes are set after firmware mismatch.

bfa_iocfc.c:
  * Handle an IOC timer issue, where the IOC timer would expire before
    the init completion and send Init fail event to the driver,
    however IOC init continues and completes successfully at the later
    stage. The bfa and driver were not handling this kind of deferred
    init completion.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Brocade CNA currently supports only 190 vports (instead of 191),
since there are only 192 unicast cam entries reserved for FCoE.

Brocade CNA has a total of 256 unicast cam entries (192 FCoE + 64 LL)

192 cam entries = 1 burned in mac + 1 baseport FPMA mac + 190 vport
FPMA macs.

Made changes to the code to support only 190 vports.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Split bfa_fcs_init() into bfa_fcs_attach() and bfa_fcs_init().

Removed empty function definitions in FCS modules

Modified driver to call bfa_fcs_attach() and bfa_fcs_init() as needed.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

 Added a FCS function to be called during driver init, to set the FDMI
 Driver parameter.

fdmi.c: Created a disabled state when fdmi is disabled.

bfad.c:
  * Added fdmi_enable driver parameter.
  * Added support to call bfa_fcs_set_fdmi_param() to initialize fcs
    fdmi setting.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

bfa_intr.c:  Enable new halt interrupt in BFA.
bfi_ctreg.h: Expose new halt interrupt bit definition to host.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

bfa_ioc.c:
  - Enable IOC auto-recovery by default.
  - When CNA is in FC mode, return IOC type as FC (not FCoE)

bfa_iocfc.c:
  - Set fcmode before pci initialization/setup.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Clear virtual links was not propagated upwards to bfa from fw.
This resulted in HBA and switch being in an inconsistent state.

So defined a new LPS event for clear virtual link on a vport,
and also now clear virtual link on a baseport, is sent as a
link down event from the fw.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Added separate MSI-X module parameters to selectively
enable / disable MSI-X interrupts for both Brocade HBA and CNA's.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

RAID attributes uses scsi_is_sdev_device() to gate some SCSI specific
checking code.  This causes two problems.  Firstly if SCSI == n just
defining scsi_is_sdev_device() to return false might not be enough to
prevent gcc from emitting the code (and thus referring to undefined
symbols), so this needs surrounding with an ifdef.  Secondly, using
scsi_is_sdev_device() when SCSI is either y or m gives a subtle
problem in the m case: raid_attrs must also be m to use the symbol.
Do the usual Kconfig jiggery-pokery to fix this.
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Doing CHECK="smatch --two-passes gives:
drivers/scsi/osd/osd_initiator.c +1435 osd_finalize_request warning: assignment to 'ret' was never used

Which is an unchecked possible allocation failure, Fixed.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Commit e3deec09 incorrectly assumed that the B0 and B1 page lengths were
limited to 32 bytes.  The B0 VPD page length is defined to be 64 bytes
when the device supports thin provisioning.  B1 is always defined to be
64 bytes.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Added round robin FCF failover on initial or FCF rediscovery FLOGI failure.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Prevent Vport discovery after reg_new_vport completes when physical
  logged in using FDISC.
- Remove fast FCF failover fabric name matching. Allow failover to FCFs
  connected to different fabrics.
- Added fast FCF failover in response to FCF DEAD event on current
  FCF record.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Clear LPFC_DRIVER_ABORTED on FCP command completion.
- Clear exchange busy flag when I/O is aborted and found on aborted list.
- Free sglq when XRI_ABORTED event is processed before release of IOCB.
- Only process iocb as aborted when LPFC_DRIVER_ABORTED is set.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Add Logging message for critial errors.
- Remove unused variable from lpfc_nodev_tmo_show
- Update supress_link_up parameter with #define values.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Add NULL checks to the pointers for the config_async mailbox
  and dump_wakeup_params mailbox.
- Add code to check return value of lpfc_read_sparams everywhere
  and handle failures appropriately.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>