Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

For some reason the include header wasn't changed from v4l2-i2c-drv-legacy.h
to v4l2-i2c-drv.h in the previous patch. This is now corrected.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Thanks to Steve Toth from Hauppauge with providing me with the information
needed to add support for these models.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

ATSC works with offset=0
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When an I2C message specifies a write then a read from the same I2C address,
we need to tell the chip to not release the bus between the message parts.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Some more I2C traces and a experimentation with register values on
both the ZL10353 and MT352 mean that I can now guess at what more
of the ZL10353 registers do.

Guess at the registers' names (based on the equivalent names in MT352)
and update set_parameters/get_parameters with the new knowledge.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

It seems that the DTV78 firmware is intended for use in locations where
VHF channels have 7MHz bandwidth and UHF channels have 8MHz bandwidth.
If we switch to DTV78 firmware when we detect this condition, we can
avoid firmware reloads when switching between VHF and UHF transponders.

Place the state for this in the control structure so that card drivers
can hint to us to use DTV78 firmware from the first tuning attempt.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

We have been inserting a mystery 500kHz offset for tuning 7MHz channels,
however some experimentation reveals it is only needed under certain
conditions with specific firmware combinations.  Document these and only
apply the offset when we know it is required.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When searching for the right S-Code table to load, check the HAS_IF flag
against the firmware we are checking instead of against the the "type"
requested.  We already ignore the scode type requested if the caller passed
an int_freq; this makes the search by frequency consistent with that behaviour.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Don't modify the control structure that was provided at attach when applying
an offset to the S-Code, otherwise it will be incorrect on subsequent tunes.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add "int_freq" to the debugging output when selecting firmware and the
HAS_IF flag when dumping firmware during load.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The patch below adds the "Pinnacle Dazzle DVC 100" to the list of
cards supported by the em28xx driver. As the configuration is the same
as the DVC 90 one, it simply adds a new USB ID to the list of devices
supported by the DVC 90 configuration.
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Check pci_register_driver() error in module_init.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Ensure that the audio is muted at attach-time
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

struct tuner holds state for tuner-core, only -- move it into tuner-core.c
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

replace tda9887_info and tda9887_dbg printk macros with
tuner_info and tuner_dbg, defined in tuner-i2c.h
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Use TUNER_SET_CONFIG to set configuration in tda9887's private state
structure, rather than storing tda9887-specific configuration within
struct tuner.

Update handling of TUNER_SET_CONFIG by tuner-core, to call
&t->fe.ops.analog_demod_ops rather than &t->fe.ops.tuner_ops

analog_demod_ops.set_config passes the request to tuner_ops.set_config,
so this does not break other drivers.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Prevent us from wasting some extra bytes of memory

Thanks to Trent Piepho, for pointing this out.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The auto selection of pertinent helper chips (VIDEO_HELPER_CHIPS_AUTO)
should select the wm8775 driver, which is used by at least one
Conexant 2388x based card (Hauppauge HVR-1300), if VIDEO_CX88 is
selected.
Signed-off-by: NFrej Drejhammar <frej.drejhammar@gmail.com>
Signed-off-by: NRicardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

All cx2388 boards need the line-in audio to be routed from an external ADC
(refered to as "ADC mode" in the spec sheet), since the chip is uncapable
of dealing with baseband audio directly.
So... this patch enables normal mode when using the tuner (TV or Radio), and
enables ADC mode with any other source. It'll probably only work with boards
that have supported ADCs (such as the Wolfson wm9775)
Signed-off-by: NRicardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

We should not mute the audio input when we stop the codec,
because it will interfere with the live uncompressed stream.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Reviewed-by: NJelle Foks <jelle@foks.8m.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix lack of audio on the MPEG-2 stream of wm8775 based blackbirds.

The wm8775 module initializes the audio input at "route 2", which doesn't
hold true for all boards. The HVR-1300, for example, uses route 1 for
tuner audio, and route 2 for baseband. So we must route the audio to the
proper input depending on what video input is being used.
Signed-off-by: NRicardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Remove the unnecessary BLACKBIRD_UNMUTE calls to the mpeg encoder in
cx88-blackbird.c

The encoder is never muted, hence unmuting should then only be necessary
once after hardware initialization.

I tested this from warm boots and cold boots (with long power down time
to ensure the sram in the chip is emptied), and found that after the
firmware upload the encoder is apparently not muted, making the unmutes
unnecessary.
Signed-off-by: NJelle Foks <jelle@foks.8m.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Remove the unnecessary msleep()'s in cx88-blackbird.c
Signed-off-by: NJelle Foks <jelle@foks.8m.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch should fix the 'muted audio' and 'raspy audio' problem for
mpeg2 streams out of cx88-blackbird devices.

Especially mythtv users would find that the audio would often sound bad
(aliased, or 'raspy'), mainly related to channel changes, many (all?)
other users would find that there was no audio at all in the mpeg data
from the encoder chip, unless the audio was manually unmuted.

The patch includes the following modifications:

Don't actually start the mpeg2 encoder until the device is read from
by the application.

Wait until the audio is stable for at least 400ms before starting the
mpeg encoder.

Mute/Unmute the audio when starting/stopping the mpeg encoder.

Stop the mpeg encoder when changing parameters and when changing tuner
frequency.

Add a variable 'mpeg_active' to struct cx8802_dev to allow tracking of
whether or not the mpeg2 encoder is active.

Load the firmware on cx88-blackbird driver load.
Signed-off-by: NJelle Foks <jelle@foks.8m.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

ATSC standard-specific firmware is D2633 on both v2.5 and v2.7. Better to
auto-select this firmware, overriding ctrl.d2633.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

use VSB IF frequency ( 44 / 5.38 MHz ) if qam_if is invalid or unspecified
Acked-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

On the s5h1409 demod, the IF frequency for VSB is limited to 44 / 5.38 MHz.

Hardcode VSB IF frequency within the driver to 44 / 5.38 MHz.
QAM IF frequency remains configurable via attach-time configuration.
Acked-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>