Before we start committing a transaction, we call
__journal_clean_checkpoint_list() to cleanup transaction's written-back
buffers.

If this call happens to remove all of them (and there were already some
buffers), __journal_remove_checkpoint() will decide to free the transaction
because it isn't (yet) a committing transaction and soon we fail some
assertion - the transaction really isn't ready to be freed :).

We change the check in __journal_remove_checkpoint() to free only a
transaction in T_FINISHED state.  The locking there is subtle though (as
everywhere in JBD ;().  We use j_list_lock to protect the check and a
subsequent call to __journal_drop_transaction() and do the same in the end
of journal_commit_transaction() which is the only place where a transaction
can get to T_FINISHED state.

Probably I'm too paranoid here and such locking is not really necessary -
checkpoint lists are processed only from log_do_checkpoint() where a
transaction must be already committed to be processed or from
__journal_clean_checkpoint_list() where kjournald itself calls it and thus
transaction cannot change state either.  Better be safe if something
changes in future...
Signed-off-by: NJan Kara <jack@suse.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Writing to XIP files at a non-page-aligned offset results in data corruption
because the writes were always sent to the start of the page.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The AMD CS5535/CS5536 GPIO has two alternate output modes: AUX-1 and AUX-2.
When either AUX is enabled, the cs5535_gpio driver cannot control the
output.

Some BIOS code for the Geode processor enables AUX-1 for GPIO-1, which
configures it as the PC BEEP output.

This patch will disable AUX-1 and AUX-2 when the user enables output.
Signed-of-by: NBen Gardner <gardner.ben@gmail.com>
Cc: Richard Knutsson <ricknu-0@student.ltu.se>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

register_sysctl_table() can return NULL sometimes, e.g.  when kmalloc()
returns NULL or when sysctl check fails.

I've also noticed, that many (most?) code in the kernel doesn't check for
the return value from register_sysctl_table() and later simply calls the
unregister_sysctl_table() with potentially NULL argument.

This is unlikely on a common kernel configuration, but in case we're
dealing with modules and/or fault-injection support, there's a slight
possibility of an OOPS.

Changing all the users to check for return code from the registering does
not look like a good solution - there are too many code doing this and
failure in sysctl tables registration is not a good reason to abort module
loading (in most of the cases).

So I think, that we can just have this check in unregister_sysctl_table
just to avoid accidental OOPS-es (actually, the unregister_sysctl_table()
did exactly this, before the start_unregistering() appeared).
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

 - reconfigure SPI baud from speed_hz of each spi transfer
 - according to spi_transfer.bits_per_word to reprogram register and setup
   correct SPI operation handlers
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time

 - move this static things to the blackfin board file
 - add pin_req array to struct bfin5xx_spi_master
 - tested on BF537/BF548 with SPI flash
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Set correct baud for spi mmc and enable SPI only after DMA is started.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move cs_chg_udelay handling (specific to this driver) to cs_deactive(), fixing
a bug when some SPI LCD driver needs delay after cs_deactive.

Fix bug reported by Cameron Barfield <cbarfield@cyberdata.net>
https://blackfin.uclinux.org/gf/project/uclinux-dist/forum/?action=ForumBrowse&forum_id=39&_forum_action=ForumMessageBrowse&thread_id=23630&feedback=Message%20replied.

Cc: Cameron Barfield <cbarfield@cyberdata.net>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix bug in u16_cs_chg_reader to read data_len-2 bytes data firstly, then read
out the last 2 bytes data
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move global SPI regs_base and dma_ch to struct driver_data.  Test on BF54x SPI
Flash with 2 spi_master devices enabled.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move spin/waits to more correct locations in bfin SPI driver.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix SPI driver to work with SPI flash ST M25P16 on bf548

Currently the SPI driver enables the SPI controller and sets the SPI baud
register for each SPI transfer.  But they should never be changed within a SPI
message session, in which several SPI transfers are pumped.

This patch moves SPI setting to the begining of a message session, and
never disables SPI controller until an error occurs.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move pin muxing to setup and cleanup methods.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use portmux mechanism to support SPI busses 1 and 2, instead of just the
original bus 0.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update spi driver to support multi-ports by using platform resources; tested
on STAMP537+SPI_MMC, other boards need more testing.  Plus other minor
updates.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Prevent people from setting bits in ctl_reg that the SPI framework already
handles, hopefully we can one day drop ctl_reg completely
Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Respect per-transfer cs_change field (protocol tweaking support) by
adding and using cs_active/cs_deactive functions.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cleanup and error handling

 - add error handling in SPI bus driver with selecting clients
 - use proper defines to access Blackfin MMRs
 - remove useless SSYNCs
 - cleaner use of portmux calls
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use new Blackfin portmux interface, add error handling.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Initial BF54x SPI support

 - support BF54x SPI0
 - clean up some code (whitespace etc)
 - will support multiports in the future
 - start using portmux calls
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Given the patch which simplifies the spi_sync calling convention, this one
updates the callers of that routine which tried using it according to the
previous specification.  (Most didn't.)
Signed-off-by: NMarc Pignat <marc.pignat@hevs.ch>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Simplify spi_sync calling convention, eliminating the need to check both
the return value AND the message->status.  In consequence, this corrects
misbehaviours of spi_read and spi_write (which only checked the former) and
their callers.
Signed-off-by: NMarc Pignat <marc.pignat@hevs.ch>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add comment to at25 driver that it's for EEPROM chips, not FLASH
chips ... the AT25 series has both types of chip, and sometimes
they're even pin-compatible.  The command sets are different, as
is the treatment of erasure.  (FLASH needs explicit erasure, but
with EEPROM it's implicit.)  Note that all vendors seem to have
this same confusion in their *25* series SPI memory parts.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make spi_write_then_read() use a mutex not a binary semaphore.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

mm/slub.c exports ksize(), but mm/slob.c and mm/slab.c don't.

It's used by binfmt_flat, which can be built as a module.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

this call should use the array index j, not i.  But with this approach, just
one int i is enough, int j is not needed.
Signed-off-by: NDenis Cheng <crquan@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes regression, introduced since 2.6.16.  NextStep variant of
UFS as OpenStep uses directory block size equals to 1024.  Without this
change, ufs_check_page fails in many cases.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NEvgeniy Dushistov <dushistov@mail.ru>
Cc: Dave Bailey <dsbailey@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We must make sure that the RTC_DEV_BUSY flag has proper lock semantics,
i.e.  that the RTC_DEV_BUSY stores clearing the flag don't get reordered
before the preceeding stores and loads and vice versa.

Spotted by Nick Piggin.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently we are complicating the code in copy_process, the clone ABI, and
if we fix the bugs sys_setsid itself, with an unnecessary open coded
version of sys_setsid.

So just simplify everything and don't special case the session and pgrp of
the initial process in a pid namespace.

Having this special case actually presents to user space the classic linux
startup conditions with session == pgrp == 0 for /sbin/init.

We already handle sending signals to processes in a child pid namespace.

We need to handle sending signals to processes in a parent pid namespace
for cases like SIGCHILD and SIGIO.

This makes nothing extra visible inside a pid namespace.  So this extra
special case appears to have no redeeming merits.

Further removing this special case increases the flexibility of how we can
use pid namespaces, by not requiring the initial process in a pid namespace
to be a daemon.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On 2.6.24, top started showing 100% iowait on one CPU when a UML instance was
running (but completely idle).  The UML code sits in io_getevents waiting for
an event to be submitted and completed.

Fix this by checking ctx->reqs_active before scheduling to determine whether
or not we are waiting for I/O.
Signed-off-by: NJeff Moyer <jmoyer@redhat.com>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'upstream-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  PHY: Add the phy_device_release device method.
  gianfar: fix compile warning
  pasemi_mac: Fix reuse of free'd skb
  SMC911X: Fix using of dereferenced skb after netif_rx
  sky2: recovery deadlock fix
  Fix memory corruption in fec_mpc52xx
  Don't claim to do IPv6 checksum offload
  cxgb - revert file mode changes.

Lately I've got this nice badness on mdio bus removal:

Device 'e0103120:06' does not have a release() function, it is broken and must be fixed.
------------[ cut here ]------------
Badness at drivers/base/core.c:107
NIP: c015c1a8 LR: c015c1a8 CTR: c0157488
REGS: c34bdcf0 TRAP: 0700   Not tainted  (2.6.23-rc5-g9ebadfbb-dirty)
MSR: 00029032 <EE,ME,IR,DR>  CR: 24088422  XER: 00000000
...
[c34bdda0] [c015c1a8] device_release+0x78/0x80 (unreliable)
[c34bddb0] [c01354cc] kobject_cleanup+0x80/0xbc
[c34bddd0] [c01365f0] kref_put+0x54/0x6c
[c34bdde0] [c013543c] kobject_put+0x24/0x34
[c34bddf0] [c015c384] put_device+0x1c/0x2c
[c34bde00] [c0180e84] mdiobus_unregister+0x2c/0x58
...

Though actually there is nothing broken, it just device
subsystem core expects another "pattern" of resource managment.

This patch implement phy device's release function, thus
we're getting rid of this badness.

Also small hidden bug fixed, hope none other introduced. ;-)
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Eliminate an uninitialized variable warning.  The code is correct, but
a pointer to the automatic variable 'addr' is passed to dma_alloc_coherent.
Since addr has never been initialized, and the compiler doesn't know
what dma_alloc_coherent will do with it, it complains.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Turns out we're freeing the skb when we detect CRC error, but we're
not clearing out info->skb. We could either clear it and have the stack
reallocate it, or just leave it and the rx ring refill code will reuse
the one that was allocated.

Reusing a freed skb obviously caused some nasty crashes of various kind,
as reported by Brent Baude and David Woodhouse.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Prevent deadlock in sky2 recovery logic. sky2_down calls napi_synchronize
which gets stuck if napi was already disabled.

Fix by rearranging slightly and not calling napi_disable until after
both ports are stopped. The napi_disable probably is being overly
paranoid, but it is safe now.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The mpc5200 fec driver is corrupting memory. This patch fixes two bugs
where the wrong skb was being referenced.
Signed-off-by: NJon Smirl <jonsmirl@gmail.com>
Acked-by: NDomen Puncer <domen.puncer@telargo.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>