The firmware doesn't relate the scan to a vif. The scan is
run by a separate entity called auxiliary MAC (aka AUX MAC).
This AUX MAC needs to get Tx power limitations that are
not applied on a specific vif, but on the device as a whole.

This can be implemented by using the minimum of all the
values set by the user for all the MACs. But then we need
to ignore the limitations that come from the AP or
regulatory for a specific vif: a specific vif might have
regulatory limitations because of the channel is works on.
This limit is irrelevant for the AUX MAC.
Use the new API from mac80211: the user_power_level in
bss_conf to achieve this.

Firmware -13.ucode has already moved to this API.

Change-Id: Ifba83660f378e91b93bd46d29fe8ba35a7c168a4
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Every tracing file must have its own TRACE_SYSTEM defined.
The brcmsmac tracepoint header broke this and added in the middle
of the file:

 #undef TRACE_SYSTEM
 #define TRACE_SYSTEM brcmsmac

 #undef TRACE_SYSTEM
 #define TRACE_SYSTEM brcmsmac_tx

 #undef TRACE_SYSTEM
 #define TRACE_SYSTEM brcmsmac_msg

Unfortunately, this broke new code in the ftrace infrastructure.
Moving each of these TRACE_SYSTEMs into their own trace file with
just one TRACE_SYSTEM per file fixes the issue.

Link: http://lkml.kernel.org/r/5524D99C.1050902@broadcom.comAcked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Every tracing file must have its own TRACE_SYSTEM defined.
The iwlwifi tracepoint header broke this and added in the middle
of the file:

 #undef TRACE_SYSTEM
 #define TRACE_SYSTEM iwlwifi_io

 #undef TRACE_SYSTEM
 #define TRACE_SYSTEM iwlwifi_ucode

 #undef TRACE_SYSTEM
 #define TRACE_SYSTEM iwlwifi_msg

 #undef TRACE_SYSTEM
 #define TRACE_SYSTEM iwlwifi_data

 #undef TRACE_SYSTEM
 #define TRACE_SYSTEM iwlwifi

Unfortunately, this broke new code in the ftrace infrastructure.
Moving each of these TRACE_SYSTEMs into their own trace file with
just one TRACE_SYSTEM per file fixes the issue.

Link: http://lkml.kernel.org/r/1428479094.2809.3.camel@sipsolutions.netReviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

ar9550 or later chips, the AR_GPIO_IN_OUT register only can
control GPIO[0:3]. For the extra GPIO, use standard GPIO calls
instead of WMAC internal registers.
Signed-off-by: NMiaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fix a spelling typo in MODULE_DESCRIPTION in
wl1251/main.c
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use bool constants as the return values instead of 1 and 0.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

rtl8192cu can't connect to AP after physical reconnect.
according to dmesg, that problem's cause was DHCP timeout.

rtl_is_special_data function checks packet type for adjusting rate.
when that function is called from _rtl_rc_get_highest_rix, it can not
calculate offset correctly. so i add argument is_encn in rtl_is_special_data.
is_enc variable mean that iv header is added in skb parameter.

i test only rtl8192cu chipset. because i doesn't have other rtlwifi chipsets.
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

As the driver may send multiple wmi commands with identical cmd id,
it is more robust to check seq number for timeout instead.
Signed-off-by: NFred Chou <fred.chou.nd@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The only other way to catch these would have been to monitor
the Tx deauth event, but we can send a deauth when we roam.
So it would have been tricky to make sure we capture the
connection losses only.
Define a separate trigger for the connection losses to make
it easier to catch them.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This will allow to collect data when a time event
notifcation with a certain id and action is coming from
the firmware. This can be very useful to debug various
flows.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The current code has a lot of duplicates of printing into a buffer
(while having to make sure it's NUL-filled and -terminated) and
then passing that to the debug trigger collection.

Since that's error-prone, instead make the debug trigger collection
function take a format string and format arguments (with compiler
validity checking) and handle the buffer internally.

This makes one behavioural change -- instead of sending the whole
buffer to userspace (clearing is needed to not leak stack data) it
just passes the actual string (including NUL-terminator.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Fix spelling error across the driver.
Modified only comments and prints.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If ucode_loaded isn't true the function returns the 'ret' variable
without having assigned a value properly. Fix that.
Reported-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This will allow to catch failures in MLME and get the
firmware data when this happens.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The str/len arguments to iwl_fw_dbg_trigger_simple_stop() aren't used,
and for a simple trigger don't really need to be used as the trigger
code itself encodes the reason, so remove them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Sending multiple action frames off channel, one after the other can create
a race that will result in a timeout:

1. Start sending action frame off channel.
2. Once the frame is sent or the time event is over, the flow will
eventually call ieee80211_start_next_roc to start the next roc frame &
iwl_mvm_roc_finished schedules to schedule a work to flush the queue.
3. Start sending new roc frame and write it to the queue before the
flush work has started.
4. The work is called and it flushes the new packet that was placed on the
on the queue so the packet is lost.

This causes the frame to be removed & not sent, that causes a timeout in
userspace.

Flush the work queue that flushes the roc/off channel queue before starting
to send a new frame off channel, in order to avoid a race between the new
frame that is transmitted off channel & the flushing of the queue.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently the last found MCC is reconfigured only in the recovery flow.
But it should always be used when available, for the ifdown/up or
RF-Kill/CT-Kill scenarios.
While at it, fix a couple of bugs in the init-from-last-MCC flow. Return
an error value when a current MCC is not found. Pass on the regdomain to
cfg80211 only if it was changed and don't ignore the return value from
the cfg80211-setter function.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Our testers need to know the number of scans performed while in
net-detect mode before the device wakes up.  The firmware already
passes this information to the driver, so we can save it and report it
in a debugfs entry.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Minor cleanup and refactoring.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we access the triggers we need to make sure that the
data we expect was actually provided by the firmware file.
Check this when we decode the triggers from the firmware
file.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add new ID for ASUS N10 WiFi dongle.
Signed-off-by: NMarek Vasut <marex@denx.de>
Tested-by: NMarek Vasut <marex@denx.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: John W. Linville <linville@tuxdriver.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

USB ID 2001:330d is used for a D-Link DWA-131.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This will expose in /sys whether the ifname of a device is set by
userspace or generated by the kernel. The latter kind (wlanX, etc)
is not deterministic, so userspace needs to rename these devices
to names that are guaranteed to stay the same between reboots. The
former, however should never be renamed, so userspace needs to be
able to reliably tell the difference.

Similar functionality was introduced for the rtnetlink core in
commit 5517750f ("net: rtnetlink - make create_link take name_assign_type")
Signed-off-by: NTom Gundersen <teg@jklm.no>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
[reformat changelog to fit 72 cols]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch adds recovery mechanism for SDIO RX during SKB allocation
failures.
For allocation failures during multiport aggregation, we skip and drop RX
packets.
For single port read case, we will use preallocated card->mpa_rx.buf to
complete cmd53 read.
Now we terminate SDIO operations only upon cmd53 failures.

CC: James Cameron <quozl@laptop.org>
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Cancel all pending commands including scan commands and stop CAC
during cfg80211 suspend handler.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

"adapter->sleep_cfm" is always non-NULL at this point.  Static checkers
complain that we already dereference it at the start of the function
when we do:

	skb_put(adapter->sleep_cfm, sizeof(struct mwifiex_opt_sleep_confirm));
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

SDIO reset was not happening properly on mwifiex as cancel_work_sync
in mwifiex_sdio_remove used to kill the calling work function itself.
Due to this, the interface was not getting removed and card was not
getting added again. Reset work function has been made independent
of adapter variable and cancel_work_sync has been moved to cleanup
function.
Signed-off-by: NMaithili Hinge <maithili@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

replace REG_WRITE to REG_RMW and place every thing in one
RMW buffer.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

it is possible to reduce time needed for this function
by rplacing REG_WRITE with REG_RMW (plus dummy 0) and putt all commands
in same buffer.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

it will reduce exution time from 14ms to 2ms on ar9271
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

use REG_RMW in ath9k_hw_analog_shift_rmw.
It will double execution speed on usb bus.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

this will reduce some overhead on usb bus.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

insted of reading each register separatly
and waste 4ms on each operation, we can
use one shot read.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

REG_READ generate most overhead on usb bus. It send and read micro packages
and reduce usb bandwidth. To reduce this overhead we should read in batches.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>