Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

T10 Diff fixes and enhancements:

- Add SLI4 Lancer support for T10 DIF / BlockGuard (121980)
- Fix SLI4 BlockGuard behavior when protection data is generated by HBA (121980)
- Enhance debugfs for injecting T10 DIF errors (123966, 132966)
- Fix Incorrect usage of bghm for BlockGuard errors (127022)
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

SLI related fixes:

- Fix REG_RPI fails on SLI4 HBA putting NPort into NPR state (126230)
- Fix ELS FDISC failing with local reject / invalid RPI. (126350)
- Fix reset port when reset is needed during fw_dump (125807)
- Fix unbounded firmware revision string from port cause panic (126560)
- Fix driver behavior when receiving an ADISC (126654)
- Fix driver not returning when bad ndlp found in abts error event
  handling (126209)
- Add more driver logs in area of SLI4 port error attention and reset
  recovery (126813, 124466)
- Fix failure in handling large CQ/EQ identifiers in an IOV
  environment (126856)
- Fix for driver using duplicate RPIs after lancer port reset (126723)
- Clear vport->fc_myDID in lpfc_els_issue_fdisc to guarentee a
  zero SID (126779, 126897)
- Fix for SLI4 Port delivery for BLS ABORT ACC (126289)
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

- Add Basic support for SLI4 Loopback.
  (CR 124951, 125766, 124951, 125843, 125832, 125843)
- Added missing protection in setting/clearing of phba->link_flag bit
  field (CR 125994)
- Use link type and link number obtained from READ_CONFIG mailbox
  command. (CR 126264)
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

FC and SCSI Discovery Fixes:

- Clear the virtual fabrics bit (word 1 bit 30) when sending the FLOGI
  and FDISC. (CR 124339)
- Return a MLQUEUE_DEVICE_BUSY if the driver detects that an I/O is being
  retried too quickly (CR 124668)
- Remove NDLP reference put in lpfc_cmpl_els_logo_acc for all but fabric
  nodes (CR 123924)
- Only retry FDISCs every second and stop retrying after devloss number
  of retries (CR 13939)
- Check to see if vports are unloading before adding them to the vport
  work array. (CR 124996)
- Fixed illegal state transition during driver unload (CR 124191)
- Added missing protection on setting/clearing of vport->fc_flag bit (CR 126002)
- Set NPIV flag in lpfc_mbx_process_link_up for all ports sli3 and
  above. (CR 126094)
- Clear FCP command bytes that are not used. (CR 126209)
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Miscellaneous fixes in sysfs and mgmt interfaces:

- Added SLI4 INTF_TYPE and SLI_FAMILY as sub-field to the fwrev sysfs
  attribute (CR 124103)
- Added a sysfs attribute "protocol" to report SLI4 port link protocol
  type (CR 124102)
- Increment mix-and-match minor number by 1 for added "protocol" sysfs
  attribute. (124102)
- Move the link speed check into the generic sli3/sli4 code
  path. (CR 124185, 124122)
- Deleted check for inExtWLen (CR 122523)
- Add the word "offline" to message 2889 (CR 124385)
- Conditionalize the firmware upgrade/downgrade so that it is only
  attempted for SLI4 type 2 boards (CR 124406)
- Return an error if the mbox sysfs is called. (CR 124210)
- When port_state is less than LPFC_VPORT_READY, report
  FC_PORTSTATE_BYPASSED (CR 120018)
- Added driver support for performing persistent linkdown based on
  configure region 23 (CR 124534)
- Added restore state and error log when sysfs board_mode attribute
  access failed (CR 124158)
- Added support for SLI4_CONFIG non-embedded COMN_GET_CNTL_ADDL_ATTR
  pass-through (CR 124466)
- Rejecting un-supported multi-buffer mailbox commands (CR 124771)
- Byte swap the extended data request and response data for extended
  mailbox data (CR 125081)
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Added T10 DIFF error injection code.
Added T10 DIFF structure definitions for SLI4 devices.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Implemented new algorithm for getting physical port name for all SLI4 devices
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Changed the timeout value for flash-based SLI_CONFIG (0x9B)
mailbox command to 300 seconds for worst case flash delays.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Miscellanous logic and interface fixes

- Fix lpfc_init_vfi_cmpl to check the interface type for interface type 0
  before parsing the results.
- Cast uint32_t values that are multiplied to uint64_t before the
  multiplication.
- Instead of "break" statement when PCI read returned error, use the goto
  statement to the end of the routine after setting return value
- moved the msleep(10) to the beginning of the wait loop for checking the
  SLIPort_Status register
- Added the code to follow the existing wait for SLIPort_Status register RDY,
  ERR, and RN bits to be set by the port before proceeding to perform PCI
  function reset.
- Do not override ulpCt_h and ulpCt_l for SLI 4 ports.
- For vport delete, call lpfc_nlp_put when the vport's vpi state is not
  marked with VPI_REGISTERED.
- Added missed fields into the driver's Controller Attributes Structure
- Changed ringing EQ/CQ/RQ doorbell register to be dependent on the size
  of the queue.
- Return -EACCES in issue_reset if cfg_enable_hba_reset is zero.
- Added new logging flag LOG_FCP_UNDER 0x00040000 to qualify underrun logging.
- Add a check in the fabric name display routine to display 0 if the port
  state is <= FLOGI.
- Add a check to the switch statement in lpfc_decode_firmware_rev to check
  for an 'X'.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fix HBA initialization issues

- Swap all values that come from the firmware image on little endian systems.
  Created a new bf_get_be macro that does the same as the bf_get_le macro but
  for big endian data instead of little endian data.
- Moved the incrementing of temp_offset after the copy
  fixed the write object loop to use temp_offset to figure out where the end
  of the image is instead of offset.
- Added the necessary codes for properly bringing the driver instance offline
  and then trying to bring the port back online with the PCI function IP reset.
  If it fails to bring the SLI port back online, it will fall through to
  bringing the SLI port to HBA error offline.
- Add a call in the probe_one_s3 and probe_one_s4 routines to get the Modeldesc
- Change OCe50100 to OCe15100
- Made the error log also include the PCI BAR bitmap returned from kernel call
  pci_select_bars().
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Adapter Interface fixes and changes

- Modify the macro field from lpfc_init_vpi_vpi to lpfc_init_vfi_vpi
- Add the new CQE_CODE_RECEIVE_V1 CQE Code, add code in the driver to handle
  the new Code the same as the CQE_CODE_RECEIVE code except that there are
  two new checks for this code that will cause the driver to use the new V1
  macros for rq_id and fcf_id.
- Fix a bug in lpfc_prep_seq() where the size out of the first CQE was
  ONLY being used, even though multiple dmabufs make up the sequence,
  each have their own CQE with potentially different sizes.
- Fix bug in lpfc_bsg_ct_unsol_event() where the ulpContext and ulpWord[3]
  fields of the XMIT_SEQUENCE64_CX IOCB were being calculated incorrectly.
- Do physical to logical translation before indexing into the active
  XRI array.
- Populate physical vpi in the iocb data structure.
- Put the current accumulated total in each IOCB in the chain as we are
  walking thru then. The last IOCB in the chain should have the total
  length of the sequence.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Miscellaneous Bug fixes and code cleanup

- Fix 16G link speed reporting by adding check for 16G check.
- Change the check and enforcement of MAILBOX_EXT_SIZE (2048B)
  to the check and enforcement of BSG_MBOX_SIZE - sizeof(MAILBOX_t) (3840B).
- Instead of waiting for a fixed amount of time after performing firmware
  reset, the driver shall wait for the Lancer SLIPORT_STATUS register for the
  readiness of the firmware for bring up.
- Add logging to indicate when dynamic parameters are changed.
- Add revision and date to the firmware image format.
- Use revision instead of rev_name to check firmware image version.
- Update temporary offset after memcopy is complete for firmware update.
- Consolidated the use of the macros to get rid of duplicated register
  offset definitions.
- Removed the unused second parameter in routine lpfc_bsg_diag_mode_enter()
- Enable debugfs when debugfs is enabled.
- Update function comments for lpfc_sli4_alloc_xri and lpfc_sli4_init_rpi_hdrs.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Extend BSG infrastructure and add link diagnostics:
- Removed unnecessary copies in handling pass-through mbox cmds.
- Add embedded SLI_CONFIG support for BSG.
- Add multibuffer support.
- Implemented the setting up and tearing down Lancer FC device for performing
  internal and external loopback diagnostic tests.
- Implemented the driver support for performing new link diagnostic tests
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

This patch adds support for hardware that returns resource ids via
extents rather than contiguous ranges.

[jejb: checkpatch.pl fixes]
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

Add request-firmware support:
- Add support for request_firmware interface for INTF2 SLI4 ports.
- Add ability to reset SLI4 INTF2 ports.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

Extended hardware support and support dump images:
- Make the size to be MAILBOX_SYSFS_MAX (4096) so that it allows the maximum
  sysfs binary access interface possible.
- Add ids and model names for new hardware
- Add capability of inducing SLI4 firmware dump obj file
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

Miscellaneous Fixes and Corrections
- Remove the memset in the lpfc_sli4_remove_rpi_hdrs call.
- Correct swapping of SGE word 2 relative to offset value
- Reorganize CQ and EQ usage to comply with SLI4 Specification.
- Expand the driver to check the rn bit. Only detect an error if the error bit
  is set and the RN bit is NOT set.
- If mailbox completion code is not success AND the mailbox status is success,
  then and only then will the driver overwrite the mailbox status.
- When driver initializing device, if the device is on a PCIe bus, set
  PCI's "needs fundamental reset" bit so that EEH uses fundamental reset
  instead of hot reset for recovery.
- Prevent driver from using new WWN when changed in firmware (until driver
  reload)
- When HBA reports maximum SGE size > 0xffffffff (infinite), override
  with 0x80000000.
- Fixed potential missed SLI4 device initialization failure conditions.
- Added 100ms delay before driver action following IF_TYPE_2 function reset.
- Reverted patch to UNREG/REG on PLOGI to mapped/unmapped node.
- Add a check for the CVL received flag in the fcf inuse routine to avoid
  unregistering the fcf if Devloss fires before Delay discover timer fires.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <jbottomley@parallels.com>

Fixes related to new hardware

- Restrict driver to look at BAR2 or BAR4 only for if_type 0.
- Allow SLI4 with FCOE_MODE not set for new SLI4 FC adapters.
- Add Temporary RPI field to the ELS request WQE.
- Do not override CT field in issue_els_flogi for SLI4 IF type 2
- For RQ_CREATE_V2 mbx cmd: fill in the rqe_size and page_size for RQ_CREATE.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Miscellaneous fixes

- Do not limit RPI Count to a minimum of 64
- Fix FCFI incorrect on received unsolicited frames.
- Save the FCFI returned in the REG_FCFI mailbox command if it was successful.
- Fixed Vports not sending FDISC after lips.
- Align based on the SLI4_PAGE_SIZE.
- Fixed double byte swap on received RRQ.
- Fixed mask size for the wq_id mask from 0x7F to 0x7FFF.
- Clear FC_FABRIC flag when NPIV LOGO completes (and add a log message).
- Modified driver to skip round robin only when ulpStatus==LOCAL_REJECT
  and word4=SEQUENCE_TIMEOUT to prevent FLOGI to disconnected FCF.
- Don't add rport if driver unloading
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

FC Discovery fixes
- In lpfc_sli4_bpl2sgl byte swapping the SGL in word2.
- In lpfc_sli4_iocb2wqe byteswap the data for CMD_GEN_REQUEST64_CR type WQE.
- In lpfc_sli4_seq_abort_acc do not set the oxid into the iocb's xritag field.
- In lpfc_sli4_seq_abort_acc check the return value of lpfc_sli_issue_iocb.
- Inprove messages in this area.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Add new Queue Create Mailbox version support
- Make lpfc_bsg_wake_mbox_wait routine check the mailboxes job reference before
  using it.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Critical Errors:
- Correctly handle non-zero return lpfc_workq_post_event and return ENOMEM
- Save the irq level when locking the host_lock in lpfc_findnode_did

Bug Fixes:
- Adjust payload_length and request_length for sli4_config mailbox commands.
- Add the freed sgl/XRI to the tail of the list rather than to the head.
- Set the FC_VPORT_NEEDS_INIT_VPI on vport deletes and check it before
  issuing a fdisc on an els retry.
- Only call lpfc_hba_init_link() if phba->cfg_suppress_link_up
  is LPFC_INITIALIZE_LINK.
- Add support for SLI-4 Performance Hints
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Implement new SLI4 init procedures based on if_type:

- Add structure changes for new SLIPORT registers and BAR changes.
- Update register names to be consistent with inteface spec terms.
- Added union to encapsulate Hardward error registers.
- Rework lpfc_sli4_post_status_check() around SLI-4's SLI_INTF type
- Removed the lpfc_sli4_fw_cfg_check routine
- Segmented driver logic to include evaluation of the if_type to
  engage different behaviors.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Implement the FC and SLI async event handlers:

- Updated MQ_CREATE_EXT mailbox structure to include fc and SLI async events.
- Added the SLI trailer code.
- Split physical field into type and number to reflect latest SLI spec.
- Changed lpfc_acqe_fcoe to lpfc_acqe_fip to reflect latest Spec changes.
- Added lpfc_acqe_fc_la structure for FC link attention async events.
- Added lpfc_acqe_sli structure for sli async events.
- Added lpfc_sli4_async_fc_evt routine to handle fc la async events.
- Added lpfc_sli4_async_sli routine to handle sli async events.
- Moved LPFC_TRAILER_CODE_FC to be handled by its own handler function.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add SLI4 FC Discovery support

- Replace READ_LA and READ_LA64 with READ_TOPOLOGY mailbox command.
- Converted the old READ_LA structure to use bf_set/get instead of bit fields.
- Rename HBA_FCOE_SUPPORT flag to HBA_FCOE_MODE. Flag now indicates function
  is running as SLI-4 FC or FCoE port. Make sure flag reset each time
  READ_REV completed as it can dynamically change.
- Removed BDE union in the READ_TOPOLOGY mailbox command and added a define to
  define the ALPA MAP SIZE. Added FC Code for async events.
- Added code to support new 16G link speed.
- Define new set of values to keep track of valid user settable link speeds.
- Used new link speed definitions to define link speed max and bitmap.
- Redefined FDMI Port sppeds to be hax values and added the 16G value.
- Added new CQE trailer code for FC Events.
- Add lpfc_issue_init_vfi and lpfc_init_vfi_cmpl routines.
- Replace many calls to the initial_flogi routine with lpfc_issue_init_vfi.
- Add vp and vpi fields to the INIT_VFI mailbox command.
- Addapt lpfc_hba_init_link routine for SLI4 use.
- Use lpfc_hba_init_link call from lpfc_sli4_hba_setup.
- Add a check for FC mode to register the FCFI before init link.
- Convert lpfc_sli4_init_vpi to be called without a vpi (get it from vport).
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Add the Lancer FC and FCoE PCI IDs
- Add new SLI4 INTF register definitions
- Implement new SLI4 doorbell register
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Add new WQE fields as defined by new SLI interface to support new hardware.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Add the new Logical Link speed event support.
- Add RATOV and EDTOV to the REG_VFI mailbox command.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Correct all SLI4 code to work on big endian systems.
- Move read of sli4 params earlier so returned values are used correctly.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Add support for the INTF (Interface) PCI register.
- Add support for greater than 2 page SGLs.
- Add support for up to 32 bit BDE lengths.
- Implement the Port Capabilities Mailbox command.
- Stop checking the Minor Code in the EQE structure.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Add init_vpi mailbox command before re-registering VPI.
- Add Fast FCF failover support.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Call pci_save_state() after pci_restore_state() call to cope
  with kernel change.
- Add support for PCI BAR region 0 if BAR0 is a 64 bit register.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Display Logical Link Speed when supported and is non-zero.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

lpfc_hbadisc.c and lpfc_hw4.h accidentally got set executable.
Reported-by: NThomas Backlund <tmb@mandriva.org>
Cc: James Smart <James.Smart@Emulex.Com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix hardware/SLI relates issues:
- Fix CNA uses more than one EQ when in INTx interrupt mode.
- Fix driver tries to process failed read FCF record mailbox request.
- Fix allocating single receive buffer breaks FCoE receive queue.
- Support new read FCF record mailbox error case.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix FC protocol errors:
- Fix multi-frame unsolicited sequences not queued properly
- Fix frames for unsolicited sequences not being associated with sequence.
- Fix unsolicited frame buffer sizes are not set properly
- Fix Sequence count for unsolicited frame headers not byte swapped.
- Fix Multi-frame sequence response frames go to wrong DID.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Hardware related Fixes and Changes.
 - Added new Adapter IDs and update default Adapter names.
 - Added PCI read after EQarm doorbell PCI write to flush the write
   and avoid spurrious interrupts when in INTx mode.
 - Phase out use of ONLINE registers.
 - Fix for lost MSI interrupt
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>