Add system sleep power management support to st_lsm6dsx driver.
In particular during suspend phase each sensor is disabled and
hw fifo is configured in bypass in order to avoid subsequent
I/O operations. The patch has been tested on HiKey board device
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Remove static qualifier from st_lsm6dsx_flush_fifo() and
st_lsm6dsx_set_fifo_mode() in order to use them in system sleep pm support
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

isl29030 is basically the same chip. The only difference
is the chip's first pin. For isl29028 its named ADDR0 and
can be used to change the chip's i2c address. For isl29030
on the other hand that pin is named Ials and is an analog
current output proportional to ALS/IR. This change is
irrelevant for the Linux driver.

This has been tested on Motorola Droid 4.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Move out of storm check to apply to IIO_CHAN_INFO_RAW so the reported
results are constant between the former and the IIO_CHAN_INFO_PROCESSED
Signed-off-by: NMatt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Ensure that when an invalid value in ret or value is found -EINVAL
is returned. A previous commit broke the way the return error is
being returned and instead caused the return code in ret to be
re-assigned rather than be returned.

Fixes: 5d9854ea ("iio: hid-sensor: Store restore poll and hysteresis on S3")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Use the local uapi headers to keep in sync with "recently" added enum
values like IIO_UVINDEX.

Build tested using:
$ make -C <kernelsrcdir> tools/iio
$ make -C <kernelsrcdir>/tools iio
$ make -C <kernelsrcdir>/tools/iio

This follows a strategy similar to that used by tools/hv, tools/net and
tools/leds among others.

Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Pointer size is variours in different system, say 32bit for 4 and 64bit
for 8. The 'sizeof(infomask)' may lead to wrong bit numbers.
Signed-off-by: NOrson Zhai <orson.zhai@spreadtrum.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The "if" interface clock speed is actually derived from the "fck"
block clock, as in the hardware they are the same clock. Drop the
incorrect second "if" clock and retain only the "fck" clock.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-renesas-soc@vger.kernel.org
To: devicetree@vger.kernel.org
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The "if" interface clock speed is actually derived from the "fck"
block clock, as in the hardware they are the same clock. Drop the
incorrect second "if" clock and get the clock speed from "fck".
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch fixes the sensor platform data initialisation for st_pressure
and st_accel device drivers. Without this patch, the driver fails to
register the sensors when the user removes and re-loads the driver.

1. Unload the kernel modules for st_pressure
$ sudo rmmod st_pressure_i2c
$ sudo rmmod st_pressure

2. Re-load the driver
$ sudo insmod st_pressure
$ sudo insmod st_pressure_i2c
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Move ISL29028 ALS / Proximity Sensor out of staging and into mainline.
Signed-off-by: NBrian Masney <masneyb@onstation.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The sysfs attribute in_proximity_sampling_frequency_available currently
shows the values 1 3 5 10 13 20 83 100. These values are supposed to
correspond to the sleep values 800 400 200 100 75 50 12.5 0 (all in ms).
When passing in a sampling frequency of 3, it actually uses a sleep
time of 200ms instead of the expected 400ms value. This patch changes
the value shown by this sysfs attribute to use fixed-point numbers so
that the correct sampling frequency is shown to the user. This patch
also changes the code that updates the proximity sampling frequency to
only allow values that are shown in the _available sysfs attribute.

The original code showed the value 83 that corresponds to the sleep
time 12 ms. The data sheet actually lists 12.5 ms as the sleep time,
so the proximity frequency was updated to 80.
Signed-off-by: NBrian Masney <masneyb@onstation.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Use octal digits as suggested by checkpatch instead of deprecated macros.
Signed-off-by: NPaolo Cretaro <melko@frugalware.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Avoid this smatch error:
drivers/iio/inkern.c:751 iio_read_avail_channel_raw() error: double unlock 'mutex:&chan->indio_dev->info_exist_lock'

Fixes: 00c5f80c ("iio: inkern: add helpers to query available values from channels")
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Bosch BME280 is a combined pressure and humidity sensor
Signed-off-by: NPeter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Most of the items have been taken care of by a clean up series. Remove
the completed items and add a few new ones.
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This never got set in the ioctl. Properly set a return value of 0 on
success.
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ion_handle was introduced as an abstraction to represent a reference to
a buffer via an ion_client. As frameworks outside of Ion evolved, the dmabuf
emerged as the preferred standard for use in the kernel. This has made
the ion_handle an unnecessary abstraction and prone to race
conditions. ion_client is also now only used internally. We have enough
mechanisms for race conditions and leaks already so just drop ion_handle
and ion_client. This also includes ripping out most of the debugfs
infrastructure since much of that was tied to clients and handles.
The debugfs infrastructure was prone to give confusing data (orphaned
allocations) so it can be replaced with something better if people
actually want it.
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Nobody uses this interface externally. Drop it.
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The current model of Ion heap registration  is based on the outdated
model of board files. The replacement for board files (devicetree)
isn't a good replacement for what Ion wants to do. In actuality, Ion
wants to show what memory is available in the system for something else
to figure out what to use. Switch to a model where Ion creates its
device unconditionally and heaps are registed as available regions.
Currently, only system and CMA heaps are converted over to the new
model. Carveout and chunk heaps can be converted over when someone wants
to figure out how.
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Ion current has ion_priv.h and ion.h as header files. ion.h was intended
to be used for public APIs but Ion never ended up really having anything
public. Combine the two headers so there is only one internal header.
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Once upon a time, phys_addr_t was not everywhere in the kernel. These
days it is used enough places that having a separate Ion type doesn't
make sense. Remove the extra type and just use phys_addr_t directly.
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Several of the Ion ioctls were designed in such a way that they
necessitate compat ioctls. We're breaking a bunch of other ABIs and
cleaning stuff up anyway so let's follow the ioctl guidelines and clean
things up while everyone is busy converting things over anyway. As part
of this, also remove the useless alignment field from the allocation
structure.
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that we have proper caching, stop setting the DMA address manually.
It should be set after properly calling dma_map.
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When CMA was first introduced, its primary use was for DMA allocation
and the only way to get CMA memory was to call dma_alloc_coherent. This
put Ion in an awkward position since there was no device structure
readily available and setting one up messed up the coherency model.
These days, CMA can be allocated directly from the APIs. Switch to using
this model to avoid needing a dummy device. This also mitigates some of
the caching problems (e.g. dma_alloc_coherent only returning uncached
memory).
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Frameworks (e.g. Ion) may want to iterate over each possible CMA area to
allow for enumeration. Introduce a function to allow a callback.
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Frameworks that may want to enumerate CMA heaps (e.g. Ion) will find it
useful to have an explicit name attached to each region. Store the name
in each CMA structure.
Signed-off-by: NLaura Abbott <labbott@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-fixes-for-4.11e' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Fifth set of IIO fixes for the 4.11 cycle.

As these are rather late in the cycle, they may sneak over into 4.12.
There is a fix for a regression caused by another fix (hid sensors
hardware seems to vary a lot in how various corner cases are handled).

* ad7303
  - fix channel description. Numeric values were being passed as characters
  presumably leading to garbage from the userspace interface.
* as3935
  - the write data macro was wrong so fix it.
* bmp280
  - incorrect handling of negative values as being unsigned broke humidity
  calculation.
* hid-sensor
  - Restore the poll and hysteresis values after resume as some hardware
  doesn't do it.
* stm32-trigger
  - buglet in reading the sampling frequency

Merge tag 'iio-for-4.12d' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Fourth set of IIO new device support, features and cleanups for the 4.12 cycle

New device support
* max1117, 1118 and 1119
  - new ADC driver
* max9611
  - new ADC driver
* pm8xxx hk/xoadc
  - new driver with some shared features broken out from the SPMI vadc.
* sun4i-gpadc
  - A33 thermal sensor support (with associated rework)
* stm32-dac
  - new driver and bindings
* stm32 trigger
  - enable support of quadrature encoder device and counter modes

Features
* apds9960
  - use the runtime pm for normal suspend
* stm32-adc
  - add opition to sest resolution via devicetree
* xoadc
  - augment DT bindings to deal with some weird mux cases

Cleanups
* ad5933
  - protect direct mode using claim and release helpers
* ade7759
  - S_IRUGO and friends to octal in two goes
* adis16203
  - drop unnecessary brackets
* hid-sensor
  - fix unbalanced pm_runtieme_enable error when probing after remove
* lsm6dsx
  - use actual part numbers for device name when known
  - simplify data read pin parsing
* mpu3050
  - avoid double reporting errors

This patch fixes the following sparse warning:
ieee80211_tx.c:174:36: incorrect type in assignment (different base types)
ieee80211_tx.c:174:36: expected unsigned short [unsigned] [short] [usertype] <noident>
ieee80211_tx.c:174:36: got restricted __be16 [usertype] <noident>

by adding left side cast to __be16.
Signed-off-by: NMartin Karamihov <martinowar@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Changed the type of wpa_ie_len from (int *) to (unsigned int *) in the
function rtw_get_wpa_ie(..) to suppress signedness mismatch warnings in
rtw_generate_ie of the type-

drivers/staging/rtl8188eu//core/rtw_ieee80211.c:1009:60: warning: incorrect
type in argument 2 (different signedness)
drivers/staging/rtl8188eu//core/rtw_ieee80211.c:1009:60:    expected int
*wpa_ie_len
drivers/staging/rtl8188eu//core/rtw_ieee80211.c:1009:60:    got unsigned
int *<noident>
Signed-off-by: NAishwarya Pant <aishpant@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Changed the type of sz from (int) to (unsigned int) to suppress
signedness mismatch warnings of the type-

drivers/staging/rtl8188eu//core/rtw_ieee80211.c:258:97: warning:
incorrect type in argument 5 (different signedness)
drivers/staging/rtl8188eu//core/rtw_ieee80211.c:258:97:    expected
unsigned int [usertype] *frlen
drivers/staging/rtl8188eu//core/rtw_ieee80211.c:258:97:    got int
*<noident>
Signed-off-by: NAishwarya Pant <aishpant@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Changed the type of len from (int *) to (unsigned int *) in the
function rtw_get_ie(..) and wherever this function is called to
suppress signedness mismatch warnings of the type-

drivers/staging/rtl8188eu//core/rtw_ap.c:78:60: warning: incorrect type
in argument 3 (different signedness)
drivers/staging/rtl8188eu//core/rtw_ap.c:78:60:    expected int *len
drivers/staging/rtl8188eu//core/rtw_ap.c:78:60:    got unsigned int
*<noident>
Signed-off-by: NAishwarya Pant <aishpant@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The two different paths for an if statement are identical and hence
we can just replace it with the single statement.

Detected by CoverityScan, CID#1428443 ("Identical code for
different branches")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The comparison of mode >= 0 is redundant as mode is a u32 and this
is always true.  Remove this redundant code.

Detected with CoverityScan ("Unsigned compared against 0")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Gstreamer's v4l2src reacted poorly to certain outputs from the bcm2835
video driver's ioctl ops function vidioc_enum_framesizes, so a
workaround was created that could be activated by user input. This
workaround would replace the driver's ioctl ops struct with another,
similar struct--only with no function pointed to by
vidioc_enum_framesizes. With no response, gstreamer would attempt to
continue with some default settings that happened to work better.

However, this bug has been fixed in gstreamer since 2014, so we
shouldn't include this workaround in the stable version of the driver.
Signed-off-by: NKevin Wern <kevin.m.wern@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Checkpatch emits WARNING: quoted string split across lines.

Concatenate string onto single line.
Signed-off-by: NTobin C. Harding <me@tobin.cc>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Driver SDIO code uses helper functions to do IO to the SDIO
device. Current helpers handle IO of a single byte as well as
multi-byte. Driver predominately uses single byte IO. If the
common case is made simple it simplifies the whole driver. The common
case can be made simple by splitting the multi-byte and single byte
calls into separate functions, i.e 4 functions in total, read single
byte, read multi-byte, write single byte, write multi-byte.

Also, we need to handle the debug code. Currently debug calls after
read/write fail access the IO buffer. This buffer, at best, does not hold
useful data on the error path, at worst is uninitialized and holds
garbage.

Split read/write helper functions into two functions each, one for
single byte IO and one for multi-byte IO. Fix all call sites. Do not
change the program logic.
Signed-off-by: NTobin C. Harding <me@tobin.cc>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Checkpatch emits CHECK: Please don't use multiple blank lines.

Remove multiple blank lines.
Signed-off-by: NTobin C. Harding <me@tobin.cc>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Checkpatch emits WARNING: please, no space before tabs.

Remove space before tabs.
Signed-off-by: NTobin C. Harding <me@tobin.cc>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>