Network coding exploits the 802.11 shared medium to allow multiple
packets to be sent in a single transmission. In brief, a relay can XOR
two packets, and send the coded packet to two destinations. The
receivers can decode one of the original packets by XOR'ing the coded
packet with the other original packet. This will lead to increased
throughput in topologies where two packets cross one relay.

In a simple topology with three nodes, it takes four transmissions
without network coding to get one packet from Node A to Node B and one
from Node B to Node A:

 1.  Node A  ---- p1 --->  Node R                Node B
 2.  Node A                Node R  <--- p2 ----  Node B
 3.  Node A  <--- p2 ----  Node R                Node B
 4.  Node A                Node R  ---- p1 --->  Node B

With network coding, the relay only needs one transmission, which saves
us one slot of valuable airtime:

 1.  Node A  ---- p1 --->  Node R                Node B
 2.  Node A                Node R  <--- p2 ----  Node B
 3.  Node A  <- p1 x p2 -  Node R  - p1 x p2 ->  Node B

The same principle holds for a topology including five nodes. Here the
packets from Node A and Node B are overheard by Node C and Node D,
respectively. This allows Node R to send a network coded packet to save
one transmission:

   Node A                  Node B

    |     \              /    |
    |      p1          p2     |
    |       \          /      |
    p1       > Node R <       p2
    |                         |
    |         /      \        |
    |    p1 x p2    p1 x p2   |
    v       /          \      v
           /            \
   Node C <              > Node D

More information is available on the open-mesh.org wiki[1].

This patch adds the initial code to support network coding in
batman-adv. It sets up a worker thread to do house keeping and adds a
sysfs file to enable/disable network coding. The feature is disabled by
default, as it requires a wifi-driver with working promiscuous mode, and
also because it adds a small delay at each hop.

[1] http://www.open-mesh.org/projects/batman-adv/wiki/CatwomanSigned-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

In C standard any expression different from 0 will be converted to
'true' when casting to bool (whatever is the length of the value).
Therefore all the "!!" conversions can be removed.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

batadv_check_unicast_packet() is changed to return a value based on the
reason to drop the packet, which will be useful information for
future users of batadv_check_unicast_packet().
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Acked-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

The batadv_priv struct carries a pointer to its own interface
struct. Therefore, it is not necessary to retrieve the soft_iface
via the primary interface.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

QLogic applications use these callbacks to perform

o  NIC Partitioning (NPAR) configuration and management
o  Diagnostic tests
o  Flash access and updates
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mugunthan V N says:

====================
This patch serires implements the following features in CPSW driver
* get/set phy link settings
* interrupt pacing
* get phy id via ioctl cmd SIOCGMIIPHY

Changes from initial version
* Made active-slave common for cpts, ethtool and SIOCGMIIPHY ioctl
* Cleaned CPSW DT binding documentation by seperating slave nodes
  under sub-section
* implemented get phy id via ioctl cmd SIOCGMIIPHY
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement get phy_id via ioctl SIOCGMIIPHY. In switch mode active phy_id
is returned and in dual EMAC mode slave's specific phy_id is returned.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements support for interrupt pacing block of CPSW via ethtool
Inetrrupt pacing block is common of both the ethernet interface in
dual emac mode
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements get/set of the phy settings via ethtool apis
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change cpts_active_slave to active_slave so that the same DT property
can be used to ethtool and SIOCGMIIPHY.

CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all the slave note properties to separate section to reduce the
confusion between slave note properties and cpsw node properties
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement to collect ethernet statistical information on ks8851_mll device.
Signed-off-by: NDavid J. Choi <david.choi@micrel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

remove cast for kmalloc/kzalloc return value.
Signed-off-by: NZhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

remove cast for kmalloc return value.
Signed-off-by: NZhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This has been tested on a qnap TS-119P II. Note that enabling WOL with
"ethtool -s eth0 wol g" is not enough; you also need to tell the PIC
microcontroller inside the qnap that WOL should be enabled by sending
0xF2 with qcontrol(1) and you have to disable EUP ("Energy-using
Products", a European power-saving thing) by sending 0xF4.
Signed-off-by: NMichael Stapelberg <michael@stapelberg.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows ethernet drivers (such as the mv643xx_eth) to support
Wake on LAN on platforms where PHY registers have to be configured
for Wake on LAN (e.g. the Marvell Kirkwood based qnap TS-119P II).
Signed-off-by: NMichael Stapelberg <michael@stapelberg.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the second of the TLP patch series; it augments the basic TLP
algorithm with a loss detection scheme.

This patch implements a mechanism for loss detection when a Tail
loss probe retransmission plugs a hole thereby masking packet loss
from the sender. The loss detection algorithm relies on counting
TLP dupacks as outlined in Sec. 3 of:
http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01

The basic idea is: Sender keeps track of TLP "episode" upon
retransmission of a TLP packet. An episode ends when the sender receives
an ACK above the SND.NXT (tracked by tlp_high_seq) at the time of the
episode. We want to make sure that before the episode ends the sender
receives a "TLP dupack", indicating that the TLP retransmission was
unnecessary, so there was no loss/hole that needed plugging. If the
sender gets no TLP dupack before the end of the episode, then it reduces
ssthresh and the congestion window, because the TLP packet arriving at
the receiver probably plugged a hole.
Signed-off-by: NNandita Dukkipati <nanditad@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch series implement the Tail loss probe (TLP) algorithm described
in http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01. The
first patch implements the basic algorithm.

TLP's goal is to reduce tail latency of short transactions. It achieves
this by converting retransmission timeouts (RTOs) occuring due
to tail losses (losses at end of transactions) into fast recovery.
TLP transmits one packet in two round-trips when a connection is in
Open state and isn't receiving any ACKs. The transmitted packet, aka
loss probe, can be either new or a retransmission. When there is tail
loss, the ACK from a loss probe triggers FACK/early-retransmit based
fast recovery, thus avoiding a costly RTO. In the absence of loss,
there is no change in the connection state.

PTO stands for probe timeout. It is a timer event indicating
that an ACK is overdue and triggers a loss probe packet. The PTO value
is set to max(2*SRTT, 10ms) and is adjusted to account for delayed
ACK timer when there is only one oustanding packet.

TLP Algorithm

On transmission of new data in Open state:
  -> packets_out > 1: schedule PTO in max(2*SRTT, 10ms).
  -> packets_out == 1: schedule PTO in max(2*RTT, 1.5*RTT + 200ms)
  -> PTO = min(PTO, RTO)

Conditions for scheduling PTO:
  -> Connection is in Open state.
  -> Connection is either cwnd limited or no new data to send.
  -> Number of probes per tail loss episode is limited to one.
  -> Connection is SACK enabled.

When PTO fires:
  new_segment_exists:
    -> transmit new segment.
    -> packets_out++. cwnd remains same.

  no_new_packet:
    -> retransmit the last segment.
       Its ACK triggers FACK or early retransmit based recovery.

ACK path:
  -> rearm RTO at start of ACK processing.
  -> reschedule PTO if need be.

In addition, the patch includes a small variation to the Early Retransmit
(ER) algorithm, such that ER and TLP together can in principle recover any
N-degree of tail loss through fast recovery. TLP is controlled by the same
sysctl as ER, tcp_early_retrans sysctl.
tcp_early_retrans==0; disables TLP and ER.
		 ==1; enables RFC5827 ER.
		 ==2; delayed ER.
		 ==3; TLP and delayed ER. [DEFAULT]
		 ==4; TLP only.

The TLP patch series have been extensively tested on Google Web servers.
It is most effective for short Web trasactions, where it reduced RTOs by 15%
and improved HTTP response time (average by 6%, 99th percentile by 10%).
The transmitted probes account for <0.5% of the overall transmissions.
Signed-off-by: NNandita Dukkipati <nanditad@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using devm_request_and_ioremap() can make the code cleaner and simpler.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCI header is not needed, so get rid of it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using for_each_set_bit() to simplify the code.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using for_each_set_bit_from() to simplify the code.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using list_move() instead of list_del() + list_add().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x FW 1.78.17 properly supports DCBX configuration for 4-port devices,
enabling FCoE support on 57840 boards.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update appropriate HSI files and adapt driver accordingly.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent bnx2x devices which are used mainly for storage from using zero
MAC addresses as their primary MAC address.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configure SFP+ tap values to optimize link signal according to NVRAM setup.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add RJ45 SFP module detection. In case the user set 10G link speed, and the
module doesn't support it, then force the speed to 1G and notify the user.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Support sysfs interface for getting the maximal number of virtual functions
   of a given physical function.
2. Support sysfs interface for getting and setting the current number of
   virtual functions.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for iproute2 callbacks allowing querying a physical
function as to its child virtual functions, and setting the macs and vlans
of said virtual functions.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using a chip operating in Single Function mode, when the chip is probed
the bnx2x would print a message warning of an unknown Multi Function mode.

This patch prevents said message.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In latest boards, the CHIP_METAL register contains an incorrect
revision value, so the correct one needs to be obtained in a
different manner.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Virtual functions don't have access to HW registers, therefore most ethtool ops
are forbidden to them. Instead of checking in each op whether the device being
driven is a virtual function or a physical function, this patch creates a
separate ethtool ops struct for virtual functions and uses it to initialize
the ethtool ops of the driver in case it is driving a virtual function device.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Release (previously leaking) memory when elements are removed from pending
execution lists in the bnx2x driver.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This uses PTR_RET instead of IS_ERR and PTR_ERR in order to increase
readability.
Signed-off-by: NSilviu-Mihai Popescu <silviupopescu1990@gmail.com>
Acked-by: N&lt;Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flag MICREL_PHY_50MHZ_CLK is not of exclusive use of KSZ8051
model. At least KSZ8021 and KSZ8031 models also use it.
This patch moves the handling of this and future flags to a
separate function so that the different PHY models can call it on
their init function, if needed.
Signed-off-by: NHector Palacios <hector.palacios@digi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>