Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 16 12月, 2013 5 次提交
    • J
      mac80211: don't delay station destruction · d34ba216
      由 Johannes Berg 提交于 
      If we can assume that stations are never referenced by the
driver after sta_state returns (and this is true since the
previous iwlmvm patch and for all other drivers) then we
don't need to delay station destruction, and don't need to
play tricks with rcu_barrier() etc.

This should speed up some scenarios like hostapd shutdown.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
      d34ba216
    • J
      mac80211: move 4-addr sta pointer clearing before synchronize_rcu() · a710c816
      由 Johannes Berg 提交于 
      The pointer should be cleared before synchronize_rcu() so that the
consequently dead station won't be found by any lookups in the TX
or RX paths.

Also check that the station is actually the one being removed, the
check is not needed because each 4-addr VLAN can only have a single
station and non-4-addr VLANs always have a NULL pointer there, but
the code is clearer this way (and we avoid the memory write.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
      a710c816
    • J
      iwlwifi: mvm: use pre-RCU-sync sta removal operation · 1ddbbb0c
      由 Johannes Berg 提交于 
      iwlmvm relies on the current mac80211 behaviour of allowing
station pointers to be valid for an RCU grace period after
returning from the sta_state() callback. To optimise these
cases, this behaviour is going away, so make the driver use
the new sta_pre_rcu_remove() method to clear the pointer in
the fw_id_to_mac_id[] array.

Since this may happen while the station is still present in
the firmware, don't set the pointer to NULL but to -ENOENT
to mark this particular case. In client mode, the station
is kept even longer (until marking the MAC as unassociated)
so the drain flow must take this new behavior into account.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
      1ddbbb0c
    • J
      mac80211: add pre-RCU-sync sta removal driver operation · 6a9d1b91
      由 Johannes Berg 提交于 
      Currently, mac80211 allows drivers to keep RCU-protected station
references that are cleared when the station is removed from the
driver and consequently needs to synchronize twice, once before
removing the station from the driver (so it can guarantee that
the station is no longer used in TX towards the driver) and once
after the station is removed from the driver.

Add a new pre-RCU-synchronisation station removal operation to
the API to allow drivers to clear/invalidate their RCU-protected
station pointers before the RCU synchronisation.

This will allow removing the second synchronisation by changing
the driver API so that the driver may no longer assume a valid
RCU-protected pointer after sta_remove/sta_state returns.

The alternative to this would be to synchronize_rcu() in all the
drivers that currently rely on this behaviour (only iwlmvm) but
that would defeat the purpose.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
      6a9d1b91
    • J
      Merge remote-tracking branch 'wireless-next/master' into mac80211-next · c4de673b
      由 Johannes Berg 提交于
      c4de673b
  3. 11 12月, 2013 11 次提交
  5. 10 12月, 2013 24 次提交