systemd > 218 fails to compile on ia64 with:

     error: ‘__NR_kcmp’ undeclared [1].

I've been told that this is because the kcmp syscall hasn't been wired up
for the ia64 arch [2].

The proposed patch thus wire up the kcmp syscall for the ia64 arch.

[1] https://bugs.gentoo.org/show_bug.cgi?id=560492
[2] https://bugs.gentoo.org/show_bug.cgi?id=560492#c17Signed-off-by: NÉmeric MASCHINO <emeric.maschino@gmail.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Pull USB fixes from Greg KH:
 "Here are three xhci driver fixes for reported issues for 4.3-rc7

  All have been in linux-next for a while with no problems"

* tag 'usb-4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  xhci: Add spurious wakeup quirk for LynxPoint-LP controllers
  xhci: handle no ping response error properly
  xhci: don't finish a TD if we get a short transfer event mid TD

Pull tty/serial fixes from Greg KH:
 "Here are two fixes that resolve reported issues, one with the 8250
  driver, and the other with the generic fbcon driver.

  Both have been in linux-next for a while"

* tag 'tty-4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  fbcon: initialize blink interval before calling fb_set_par
  Revert "serial: 8250_dma: don't bother DMA with small transfers"

Pull staging driver fixes from Greg KH:
 "Here are four iio driver fixes for 4.3-rc7, fixing some reported
  issues.  All of these have been in linux-next for a while"

* tag 'staging-4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: mxs-lradc: Fix temperature offset
  iio: accel: sca3000: memory corruption in sca3000_read_first_n_hw_rb()
  iio: st_accel: fix interrupt handling on LIS3LV02
  iio: adc: twl4030: Fix ADC[3:6] readings

Pull infiniband fixes from Doug Ledford:
 "It's late in the game, I know, but these fixes seemed important enough
  to warrant a late pull request.  They all involve oopses or use after
  frees or corruptions.

  Six serious fixes:

   - Hold the mutex around the find and corresponding update of our gid

   - The ifa list is rcu protected, copy its contents under rcu to avoid
     using a freed structure

   - On error, netdev might be null, so check it before trying to
     release it

   - On init, if workqueue alloc fails, fail init

   - The new demux patches exposed a bug in mlx5 and ipath drivers, we
     need to use the payload P_Key to determine the P_Key the packet
     arrived on because the hardware doesn't tell us the truth

   - Due to a couple convoluted error flows, it is possible for the CM
     to trigger a use_after_free and a double_free of rb nodes.  Add two
     checks to prevent that.  This code has worked for 10+ years.  It is
     likely that some of the recent changes have caused this issue to
     surface.  The current patch will protect us from nasty events for
     now while we track down why this is just now showing up"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  IB/cm: Fix rb-tree duplicate free and use-after-free
  IB/cma: Use inner P_Key to determine netdev
  IB/ucma: check workqueue allocation before usage
  IB/cma: Potential NULL dereference in cma_id_from_event
  IB/core: Fix use after free of ifa
  IB/core: Fix memory corruption in ib_cache_gid_set_default_gid

Pull device mapper fixes from Mike Snitzer:
 "Three stable fixes (two in btree code used by DM thinp and one to
  properly store flags in DM cache metadata's superblock)"

* tag 'dm-4.3-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm cache: the CLEAN_SHUTDOWN flag was not being set
  dm btree: fix leak of bufio-backed block in btree_split_beneath error path
  dm btree remove: fix a bug when rebalancing nodes after removal

Pull block layer fixes from Jens Axboe:
 "A final set of fixes for 4.3.

  It is (again) bigger than I would have liked, but it's all been
  through the testing mill and has been carefully reviewed by multiple
  parties.  Each fix is either a regression fix for this cycle, or is
  marked stable.  You can scold me at KS.  The pull request contains:

   - Three simple fixes for NVMe, fixing regressions since 4.3.  From
     Arnd, Christoph, and Keith.

   - A single xen-blkfront fix from Cathy, fixing a NULL dereference if
     an error is returned through the staste change callback.

   - Fixup for some bad/sloppy code in nbd that got introduced earlier
     in this cycle.  From Markus Pargmann.

   - A blk-mq tagset use-after-free fix from Junichi.

   - A backing device lifetime fix from Tejun, fixing a crash.

   - And finally, a set of regression/stable fixes for cgroup writeback
     from Tejun"

* 'for-linus' of git://git.kernel.dk/linux-block:
  writeback: remove broken rbtree_postorder_for_each_entry_safe() usage in cgwb_bdi_destroy()
  NVMe: Fix memory leak on retried commands
  block: don't release bdi while request_queue has live references
  nvme: use an integer value to Linux errno values
  blk-mq: fix use-after-free in blk_mq_free_tag_set()
  nvme: fix 32-bit build warning
  writeback: fix incorrect calculation of available memory for memcg domains
  writeback: memcg dirty_throttle_control should be initialized with wb->memcg_completions
  writeback: bdi_writeback iteration must not skip dying ones
  writeback: fix bdi_writeback iteration in wakeup_dirtytime_writeback()
  writeback: laptop_mode_timer_fn() needs rcu_read_lock() around bdi_writeback iteration
  nbd: Add locking for tasks
  xen-blkfront: check for null drvdata in blkback_changed (XenbusStateClosing)

Pull Ceph fixes from Sage Weil:
 "Two fixes.

  One is a stopgap to prevent a stack blowout when users have a deep
  chain of image clones.  (We'll rewrite this code to be non-recursive
  for the next window, but in the meantime this is a simple fix that
  avoids a crash.)

  The second fixes a refcount underflow"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: prevent kernel stack blow up on rbd map
  rbd: don't leak parent_spec in rbd_dev_probe_parent()

Pull btrfs fixes from Chris Mason:
 "I have two more small fixes this week:

  Qu's fix avoids unneeded COW during fallocate, and Christian found a
  memory leak in the error handling of an earlier fix"

* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: fix possible leak in btrfs_ioctl_balance()
  btrfs: Avoid truncate tailing page if fallocate range doesn't exceed inode size

If the CLEAN_SHUTDOWN flag is not set when a cache is loaded then all cache
blocks are marked as dirty and a full writeback occurs.

__commit_transaction() is responsible for setting/clearing
CLEAN_SHUTDOWN (based the flags_mutator that is passed in).

Fix this issue, of the cache's on-disk flags being wrong, by making sure
__commit_transaction() does not reset the flags after the mutator has
altered the flags in preparation for them being serialized to disk.

before:

sb_flags = mutator(le32_to_cpu(disk_super->flags));
disk_super->flags = cpu_to_le32(sb_flags);
disk_super->flags = cpu_to_le32(cmd->flags);

after:

disk_super->flags = cpu_to_le32(cmd->flags);
sb_flags = mutator(le32_to_cpu(disk_super->flags));
disk_super->flags = cpu_to_le32(sb_flags);
Reported-by: NBogdan Vasiliev <bogdan.vasiliev@gmail.com>
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

btree_split_beneath()'s error path had an outstanding FIXME that speaks
directly to the potential for _not_ cleaning up a previously allocated
bufio-backed block.

Fix this by releasing the previously allocated bufio block using
unlock_block().
Reported-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Acked-by: NJoe Thornber <thornber@redhat.com>
Cc: stable@vger.kernel.org

Commit 4c7e3093 ("dm btree remove: fix bug in redistribute3") wasn't
a complete fix for redistribute3().

The redistribute3 function takes 3 btree nodes and shares out the entries
evenly between them.  If the three nodes in total contained
(MAX_ENTRIES * 3) - 1 entries between them then this was erroneously getting
rebalanced as (MAX_ENTRIES - 1) on the left and right, and (MAX_ENTRIES + 1) in
the center.

Fix this issue by being more careful about calculating the target number
of entries for the left and right nodes.

Unit tested in userspace using this program:
https://github.com/jthornber/redistribute3-test/blob/master/redistribute3_t.cSigned-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

Mapping an image with a long parent chain (e.g. image foo, whose parent
is bar, whose parent is baz, etc) currently leads to a kernel stack
overflow, due to the following recursion in the reply path:

  rbd_osd_req_callback()
    rbd_obj_request_complete()
      rbd_img_obj_callback()
        rbd_img_parent_read_callback()
          rbd_obj_request_complete()
            ...

Limit the parent chain to 16 images, which is ~5K worth of stack.  When
the above recursion is eliminated, this limit can be lifted.

Fixes: http://tracker.ceph.com/issues/12538

Cc: stable@vger.kernel.org # 3.10+, needs backporting for < 4.2
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Reviewed-by: NJosh Durgin <jdurgin@redhat.com>

Currently we leak parent_spec and trigger a "parent reference
underflow" warning if rbd_dev_create() in rbd_dev_probe_parent() fails.
The problem is we take the !parent out_err branch and that only drops
refcounts; parent_spec that would've been freed had we called
rbd_dev_unparent() remains and triggers rbd_warn() in
rbd_dev_parent_put() - at that point we have parent_spec != NULL and
parent_ref == 0, so counter ends up being -1 after the decrement.

Redo rbd_dev_probe_parent() to fix this.

Cc: stable@vger.kernel.org # 3.10+, needs backporting for < 4.2
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Reviewed-by: NAlex Elder <elder@linaro.org>

Pull x86 fixes from Ingo Molnar:
 "Misc fixes: two KASAN fixes, two EFI boot fixes, two boot-delay
  optimization fixes, and a fix for a IRQ handling hang observed on
  virtual platforms"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm, kasan: Silence KASAN warnings in get_wchan()
  compiler, atomics, kasan: Provide READ_ONCE_NOCHECK()
  x86, kasan: Fix build failure on KASAN=y && KMEMCHECK=y kernels
  x86/smpboot: Fix CPU #1 boot timeout
  x86/smpboot: Fix cpu_init_udelay=10000 corner case boot parameter misbehavior
  x86/ioapic: Disable interrupts when re-routing legacy IRQs
  x86/setup: Extend low identity map to cover whole kernel range
  x86/efi: Fix multiple GOP device support

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes all around the map: an instrumentation fix, a nohz
  usability fix, a lockdep annotation fix and two task group scheduling
  fixes"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Add missing lockdep_unpin() annotations
  sched/deadline: Fix migration of SCHED_DEADLINE tasks
  nohz: Revert "nohz: Set isolcpus when nohz_full is set"
  sched/fair: Update task group's load_avg after task migration
  sched/fair: Fix overly small weight for interactive group entities
  sched, tracing: Stop/start critical timings around the idle=poll idle loop

Merge fixes from Andrew Morton:
 "9 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  ocfs2/dlm: unlock lockres spinlock before dlm_lockres_put
  fault-inject: fix inverted interval/probability values in printk
  lib/Kconfig.debug: disable -Wframe-larger-than warnings with KASAN=y
  mm: make sendfile(2) killable
  thp: use is_zero_pfn() only after pte_present() check
  mailmap: update Javier Martinez Canillas' email
  MAINTAINERS: add Sergey as zsmalloc reviewer
  mm: cma: fix incorrect type conversion for size during dma allocation
  kmod: don't run async usermode helper as a child of kworker thread

Luca and Wanpeng reported two missing annotations that led to
false lockdep complaints. Add the missing annotations.
Reported-by: NLuca Abeni <luca.abeni@unitn.it>
Reported-by: NWanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: cbce1a68 ("sched,lockdep: Employ lock pinning")
Link: http://lkml.kernel.org/r/20151023095008.GY17308@twins.programming.kicks-ass.netSigned-off-by: NIngo Molnar <mingo@kernel.org>

Pull powerpc fixes from Michael Ellerman:

 - Revert "Use the POWER8 Micro Partition Prefetch Engine in KVM HV on
   POWER8" from Paul
 - Handle irq_happened flag correctly in off-line loop from Paul
 - Validate rtas.entry before calling enter_rtas() from Vasant

* tag 'powerpc-4.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/rtas: Validate rtas.entry before calling enter_rtas()
  powerpc/powernv: Handle irq_happened flag correctly in off-line loop
  powerpc: Revert "Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8"

Pull ARM SoC fixes from Arnd Bergmann:
 "Most of the changes this time are for incorrect device nodes in
  various ways, on on imx, berlin, exynos, ux500, uniphier, omap and
  meson.

  Chen-Yu Tsai now co-maintains mach-sunxi (Allwinner).

  Other bug fixes include
   - a partial revert of a broken tegra gpio patch
   - irq affinity for arm ccn
   - suspend on one Armada 385 machine
   - enable ZONE_DMA to avoid an OMAP crash for over 2GB RAM
   - turning on a regulator on beagleboard-x15 for HDMI
   - making the omap gpmc debug code visible
   - setup of orion network switch
   - a rare build regression for pxa"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
  ARM: OMAP2+: Fix imprecise external abort caused by bogus SRAM init
  thermal: exynos: Fix register read in TMU
  ARM: OMAP2+: Fix oops with LPAE and more than 2GB of memory
  ARM: tegra: Comment out gpio-ranges properties
  ARM: dts: uniphier: fix IRQ number for devices on PH1-LD6b ref board
  drivers/perf: arm_pmu: avoid CPU device_node reference leak
  bus: arm-ccn: Fix irq affinity setting on CPU migration
  bus: arm-ccn: Handle correctly no-more-cpus case
  ARM: mvebu: correct a385-db-ap compatible string
  ARM: meson6: DTS: Fix wrong reg mapping and IRQ numbers
  MAINTAINERS: Update Allwinner entry and add new maintainer
  ARM: ux500: modify initial levelshifter status
  ARM: pxa: fix pxa3xx DFI lockup hack
  Documentation: ARM: List new omap MMC requirements
  memory: omap-gpmc: dump "before" state before first modification
  memory: omap-gpmc: Fix unselectable debug option for GPMC
  ARM: dts: am57xx-beagle-x15: set VDD_SD to always-on
  ARM: dts: Fix audio card detection on Peach boards
  ARM: EXYNOS: Fix double of_node_put() when parsing child power domains
  ARM: orion: Fix DSA platform device after mvmdio conversion
  ...

Pull KVM bugfixes from Paolo Bonzini:
 "Bug fixes for ARM, mostly 4.3 regressions related to virtual interrupt
  controller changes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  arm/arm64: KVM: Fix disabled distributor operation
  arm/arm64: KVM: Clear map->active on pend/active clear
  arm/arm64: KVM: Fix arch timer behavior for disabled interrupts
  KVM: arm: use GIC support unconditionally
  KVM: arm/arm64: Fix memory leak if timer initialization fails
  KVM: arm/arm64: Do not inject spurious interrupts

Merge tag 'trace-fixes-v4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
 "Running tests on other changes, the system locked up due to lots of
  warnings.  It was caused by the stack tracer triggering a warning
  about using rcu_dereference() when RCU was not watching.  This can
  happen due to the fact that the stack tracer uses the function tracer
  to check each function, and there are functions that may be called and
  traced when RCU stopped watching.  Namely when a function is called
  just before going idle or to userspace and after RCU stopped watching
  that current CPU.

  The first patch makes sure that RCU is watching when the stack tracer
  uses RCU.  The second patch is to make sure that the stack tracer does
  not get called by functions in NMI, as it's not NMI safe"

* tag 'trace-fixes-v4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Do not allow stack_tracer to record stack in NMI
  tracing: Have stack tracer force RCU to be watching

Pull sound fixes from Takashi Iwai:
 "There is nothing to worry you much, only a few small & stable patches
  are found for usual stuff, HD-audio (a Lenovo laptop quirk, a fix for
  minor error handling) and ASoC (trivial fixes for RT298 and WM
  codecs).

  The only remaining major change is the fix for ASoC SX_TLV control
  that was overseen during refactoring, but the fix itself is trivial
  and safe"

* tag 'sound-4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: wm8962: mark cache_dirty flag after software reset in pm_resume
  ASoC: rt298: fix wrong setting of gpio2_en
  ASoC: wm8904: Correct number of EQ registers
  ALSA: hda - Fix deadlock at error in building PCM
  ASoC: Add info callback for SX_TLV controls
  ASoC: rt298: correct index default value
  ALSA: hda - Fix inverted internal mic on Lenovo G50-80
  ALSA: hdac: Explicitly add io.h

Pull media fixes from Mauro Carvalho Chehab:
 "Some regression fixes and potential security issues:

   - netup_unidvb: fix potential crash when spi is NULL
   - rtl28xxu: fix control message flaws
   - m88ds3103: fix a regression on Kernel 4.2
   - c8sectpfe: fix some issues on this new driver
   - v4l2-flash-led-class: fix a Kbuild dependency
   - si2157 and si2158: check for array boundary when uploading firmware
     files
   - horus3a and lnbh25: fix some building troubles when some options
     aren't selected
   - ir-hix5hd2: drop the use of IRQF_NO_SUSPEND"

* tag 'media/v4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] m88ds3103: use own reg update_bits() implementation
  [media] rtl28xxu: fix control message flaws
  [media] v4l2-flash-led-class: Add missing VIDEO_V4L2 Kconfig dependency
  [media] netup_unidvb: fix potential crash when spi is NULL
  [media] si2168: Bounds check firmware
  [media] si2157: Bounds check firmware
  [media] ir-hix5hd2: drop the use of IRQF_NO_SUSPEND
  [media] c8sectpfe: fix return of garbage
  [media] c8sectpfe: fix ininitialized error return on firmware load failure
  [media] lnbh25: Fix lnbh25_attach() function return type
  [media] horus3a: Fix horus3a_attach() function parameters

Pull drm fixes from Dave Airlie:
 "I've been a bit slow gathering these:

   - drm/mst: one mutex leak in a fail path

   - radeon: two oops fixes, one dpm fix

   - i915: one messy set of fixes, where we revert the original fix, and
           pull back the proper set of fixes from -next on top.

   - nouveau: one fix for an illegal buffer placement.

  Doesn't look too bad, hopefully shouldn't be too much more"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau/gem: return only valid domain when there's only one
  drm: fix mutex leak in drm_dp_get_mst_branch_device
  drm/amdgpu: add missing dpm check for KV dpm late init
  drm/amdgpu/dpm: don't add pwm attributes if DPM is disabled
  drm/radeon/dpm: don't add pwm attributes if DPM is disabled
  drm/i915: Add primary plane to mask if it's visible
  drm/i915: Move sprite/cursor plane disable to intel_sanitize_crtc()
  drm/i915: Assign hwmode after encoder state readout
  Revert "drm/i915: Add primary plane to mask if it's visible"
  drm/i915: Deny wrapping an userptr into a framebuffer
  drm/i915: Enable DPLL VGA mode before P1/P2 divider write
  drm/i915: Restore lost DPLL register write on gen2-4
  drm/i915: Flush pipecontrol post-sync writes
  drm/i915: Fix kerneldoc for i915_gem_shrink_all

dlm_lockres_put will call dlm_lockres_release if it is the last
reference, and then it may call dlm_print_one_lock_resource and
take lockres spinlock.

So unlock lockres spinlock before dlm_lockres_put to avoid deadlock.
Signed-off-by: NJoseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

interval displays the probability and vice versa.

Fixes: 6adc4a22 ("fault-inject: add ratelimit option")
Acked-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When the kernel compiled with KASAN=y, GCC adds redzones for each
variable on stack.  This enlarges function's stack frame and causes:

	'warning: the frame size of X bytes is larger than Y bytes'

The worst case I've seen for now is following:

   ../net/wireless/nl80211.c: In function `nl80211_send_wiphy':
   ../net/wireless/nl80211.c:1731:1: warning: the frame size of 5448 bytes is larger than 2048 bytes [-Wframe-larger-than=]

That kind of warning becomes useless with KASAN=y.  It doesn't
necessarily indicate that there is some problem in the code, thus we
should turn it off.

(The KASAN=y stack size in increased from 16k to 32k for this reason)
Signed-off-by: NAndrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Acked-by: NAbylay Ospan <aospan@netup.ru>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently a simple program below issues a sendfile(2) system call which
takes about 62 days to complete in my test KVM instance.

        int fd;
        off_t off = 0;

        fd = open("file", O_RDWR | O_TRUNC | O_SYNC | O_CREAT, 0644);
        ftruncate(fd, 2);
        lseek(fd, 0, SEEK_END);
        sendfile(fd, fd, &off, 0xfffffff);

Now you should not ask kernel to do a stupid stuff like copying 256MB in
2-byte chunks and call fsync(2) after each chunk but if you do, sysadmin
should have a way to stop you.

We actually do have a check for fatal_signal_pending() in
generic_perform_write() which triggers in this path however because we
always succeed in writing something before the check is done, we return
value > 0 from generic_perform_write() and thus the information about
signal gets lost.

Fix the problem by doing the signal check before writing anything.  That
way generic_perform_write() returns -EINTR, the error gets propagated up
and the sendfile loop terminates early.
Signed-off-by: NJan Kara <jack@suse.com>
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use is_zero_pfn() on pteval only after pte_present() check on pteval
(It might be better idea to introduce is_zero_pte() which checks
pte_present() first).

Otherwise when working on a swap or migration entry and if pte_pfn's
result is equal to zero_pfn by chance, we lose user's data in
__collapse_huge_page_copy().  So if you're unlucky, the application
segfaults and finally you could see below message on exit:

BUG: Bad rss-counter state mm:ffff88007f099300 idx:2 val:3

Fixes: ca0984ca ("mm: incorporate zero pages into transparent huge pages")
Signed-off-by: NMinchan Kim <minchan@kernel.org>
Reviewed-by: NAndrea Arcangeli <aarcange@redhat.com>
Acked-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org>	[4.1+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The get_maintainer script still reports my old Collabora email based on
old commits but that address no longer exist so update mailmap to report
my current email and avoid people sending to the old address.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Nominate myself as a zsmalloc reviewer.
Signed-off-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This was found during userspace fuzzing test when a large size dma cma
allocation is made by driver(like ion) through userspace.

  show_stack+0x10/0x1c
  dump_stack+0x74/0xc8
  kasan_report_error+0x2b0/0x408
  kasan_report+0x34/0x40
  __asan_storeN+0x15c/0x168
  memset+0x20/0x44
  __dma_alloc_coherent+0x114/0x18c
Signed-off-by: NRohit Vaswani <rvaswani@codeaurora.org>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

call_usermodehelper_exec_sync() does fork() + wait() with "unignored"
SIGCHLD.  What we have missed is that this worker thread can have other
children previously forked by call_usermodehelper_exec_work() without
UMH_WAIT_PROC.  If such a child exits in between it becomes a zombie
because auto-reaping only works if SIGCHLD is ignored, and nobody can
reap it (unless/until this worker thread exits too).

Change the !UMH_WAIT_PROC case to use CLONE_PARENT.

Note: this is only first step.  All PF_KTHREAD tasks, even created by
kernel_thread() should have ->parent == kthreadd by default.

Fixes: bb304a5c ("kmod: handle UMH_WAIT_PROC from system unbound workqueue")
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Acked-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge tag 'asoc-fix-v4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v4.3

A bunch of driver fixes plus one core fix which fixes problems with
misreporting values from _SX controls following a recent refactoring.
This had gone unnoticed as such controls are quite rare.

Merge remote-tracking branches 'asoc/fix/rt298', 'asoc/fix/sx', 'asoc/fix/wm8904' and 'asoc/fix/wm8962' into asoc-linus

Device stopped to tuning some channels after regmap conversion.
Reason is that regmap_update_bits() works a bit differently for
partially volatile registers than old homemade routine. Return
back to old routine in order to fix issue.

Fixes: 478932b1

Cc: <stable@kernel.org> # 4.2+
Reported-by: NMark Clarkstone <hello@markclarkstone.co.uk>
Tested-by: NMark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Add lock to prevent concurrent access for control message as control
message function uses shared buffer. Without the lock there may be
remote control polling which messes the buffer causing IO errors.
Increase buffer size and add check for maximum supported message
length.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=103391
Fixes: c56222a6 ("[media] rtl28xxu: move usb buffers to state")

Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: NAntti Palosaari <crope@iki.fi>