The ar9003 table is updated to increase XLNA BIAS
output driver strengh.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Because of not clearing Bit 14 of AR_WA, the ASPM L1 is not
enabled when entering into sleep mode. AR9480 does not need
bit 14 to be set.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch takes care of warnings found by running
'make namespacecheck':

1. Remove dead code.
2. Reorder function definitions to avoid forward declarations.
3. Remove unnecessary function/structure declarations and mark
   them as static.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently global wait condition (adapter->cmd_wait_q.condition)
is used while sending synchronous commands to FW. When two threads
enter in mwifiex_send_cmd_sync() routine at the same time, both the
threads wait for their command responses. Since wait condition is
same for both, they wake up simultaneously after getting response
of 1st command. After this when a thread is waiting for command
response of 3rd command, it wakes up after getting response of 2nd
command and so on. Therefore we don't wait for the response of last
command(0xaa) during unload. Hence while next time loading the driver
command time out is seen for INIT command.

This problem is resolved by having separate wait condition flag for
each command(except scan command). Since scan command is treated
differently (by maintaining scan pending q etc.), newly defined flag
(scan_wait_q_woken) is used as a scan wait condition.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 55ad5962.

I assumed N is newer than LP, which isn't true. This regressed LP case.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Wifi.c was empty after previous cleanups, so it was removed.
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Moved the brcmu_format_flags function and brcmu_bit_desc structure
into smac. Names were adjusted accordingly.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Moved the brcmu_mkiovar function into fmac, adjusting the
name accordingly.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Moved brcmu_chspec_malformed into the only file using it. The
function name was adjusted accordingly.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Moved the brcmu_parse_tlvs function and brcmu_tlv structure into
the only file using them. Names were adjusted accordingly.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Moved the brcmu_chipname function into the only file using it.
The function name was adjusted accordingly.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Moved brcmu_mw_to_qdbm and brcmu_qdbm_to_mw functions into the only
file using them. Names were adjusted accordingly.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Removed brcmu_bitcount, brcmu_mhz2channel, brcmu_chspec_ctlchan.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

And changed function name to something more appropriate.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For scanning several timeout parameters are configured on the device.
These parameters have been endian annotated and converted appropriately.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The parameters for roaming are sent to the device and should be little
endian. These have been annotated and converted appropriately.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver requests the device for number of ie's in assoc request
and response. This needed to be endian annotated.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The pairwise master key configuration is sent to the device. The
structure has been annotated for endianess checking.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The scan related functions provide scan parameters to the device
which need to be in little-endian. These parameters have been
annotated and conversions were placed as needed.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The configuration function for the TCP offload engine were not
taking CPU endianess into account. Proper annotations and conversions
have been added.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The variable allmulti was used to provision IFF_ALLMULTI to the
device as well as IFF_PROMISC. For clarity the variable has been
renamed.
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The packet filter structures were byte copied and transferred over the
host bus to the device. As such they are little endian and have been
annotated accordingly.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ht capabilities provided upon registration with mac80211 must
be in little endian. This was fixed adding cpu_to_le16() conversion.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The debug function did a write operation which required a different
pointer type resulting in a sparse warning.
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

- removed unneeded fn prototypes from include files.
- explicitly marked fn prototypes as extern in include files.
- reordered functions to account for removed forward declarations
  in include files.
- removed unused functions: brcms_c_txflowcontrol_override,
  brcms_c_txflowcontrol_prio_isset, brcms_c_txflowcontrol.
Reviewed-by: NRoland Vossen <rvossen@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Timer functions were called at soft-irq level, leading to the limitation
that mutexes could not be used. Lifted this limitation by migrating to
work queues.
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Parameter 'wl' is already stored in struct brcms_timer, so the number of
function parameters could be decreased.
Reviewed-by: NAlwin Beukers <alwin@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reformat the check, the indentation is completely strange.
Also change the last part of the condition to make the
code shorter.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fix regression introduced by commit:

commit 15b3f3b0
Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Date:   Fri Jun 3 07:54:13 2011 -0700

    iwlagn: set smps mode after assoc for 1000 device

Also remove unneeded brackets on the way.

Address:
https://bugzilla.redhat.com/show_bug.cgi?id=744155

Cc: stable@kernel.org # 3.1+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Smatch complains that "key_index" is capped at 5 in nl80211_get_key()
but iwm->keys[] only has 4 elements.  I don't know if this is really
needed, but the other ->get_key() implementations seemed to check
for overflows so I've added a check here.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch incorporate the differences between the 06/20/2011 and
08/16/2011 Realtek releases of the rtl8192de driver.

The changes include:

1. Update for new chip versions
Signed-off-by: NChaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch incorporate the differences between the 06/20/2011 and
08/16/2011 Realtek releases of the rtl8192se driver.

The changes include:

1. Fixing some typos in register usage.
2. A change in the handling of decryption status for 802.11w packets.
Signed-off-by: NChaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch incorporate the differences between the 06/20/2011 and
08/16/2011 Realtek releases of the rtlwifi driver.

The changes include:

1. Adding new chip revisions including new firmware.
Signed-off-by: NChaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch incorporate the differences between the 06/20/2011 and
08/16/2011 Realtek releases of the rtlwifi driver.

The changes include:

1. Handling of IEEE80211_HW_CONNECTION_MONITOR.
2. Fix typo to get proper response to nullfunc frames.
Signed-off-by: NChaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 already filled in the MCS rate info for rx'ed frames but tx'ed
frames that are sent to a monitor interface during the status callback
lack this information.

Add the radiotap fields for MCS info to ieee80211_tx_status_rtap_hdr
and populate them when sending tx'ed frames to the monitors.

The needed headroom is only extended by one byte since we don't include
legacy rate information in the rtap header for HT frames.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Get rid of the ieee80211_tx_status_rtap_hdr struct and instead build the
rtap header dynamically. This makes it easier to extend the rtap header
generation in the future.

Add ieee80211_tx_radiotap_len to calculate the expected size of the
rtap header before generating it. Since we can't check if the rtap
header fits into the requested headroom during compile time anymore
add a WARN_ON_ONCE.

Also move the actual rtap header generation into its own function.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A few were missing
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>