With command to get board_id from otp, in the case of following

  boot get otp board id result 0x00000000 board_id 0 chip_id 0
  boot using board name 'bus=pci,bmi-chip-id=0,bmi-board-id=0"
  ...
  failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=0 from
  ath10k/QCA6174/hw3.0/board-2.bin

The invalid board_id=0 will be used as index to search in the board-2.bin.

Ignore the case with board_id=0, as it means the otp is not carrying
the board id information.
Signed-off-by: NRyan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The txpower is being recalculated when adding interface to make sure
txpower won't overshoot the spec, and when removing the interface,
the txpower should again to be recalculated to restore the correct value
from the active interface list.

Following is one of the scenario
	vdev0 is created as STA and connected: txpower:23
	vdev1 is created as P2P_DEVICE for control interface: txpower:0
	vdev2 is created as p2p go/gc interface: txpower is 21

So the vdev2@txpower:21 will be set to firmware when vdev2 is created.
When we tear down the vdev2, the txpower needs to be recalculated to
re-set it to vdev0@txpower:23 as vdev0/vdev1 are the active interface.

	ath10k_pci mac vdev 0 peer create 8c:fd:f0:01:62:98
	ath10k_pci mac vdev_id 0 txpower 23
	... (adding interface)
	ath10k_pci mac vdev create 2 (add interface) type 1 subtype 3
	ath10k_pci mac vdev_id 2 txpower 21
	ath10k_pci mac txpower 21
	... (removing interface)
	ath10k_pci mac vdev 2 delete (remove interface)
	ath10k_pci vdev 1 txpower 0
	ath10k_pci vdev 0 txpower 23
	ath10k_pci mac txpower 23
Signed-off-by: NRyan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Whenever firmware crashes, and both CONFIG_ATH10K_DEBUGFS and
CONFIG_ALLOW_DEV_COREDUMP are enabled, dump information about the crash via a
devcoredump device. Dump can be read from userspace for further analysis from:

/sys/class/devcoredump/devcd*/data

As until now we have provided the firmware crash dump file via fw_crash_dump
debugfs keep it still available but deprecate and a warning print that the user
should switch to using dev_coredump.

Future improvement would be not to depend on CONFIG_ATH10K_DEBUGFS, as there
might be systems which want to get the firmware crash dump but not enable
debugfs. How to handle memory consumption is also something which needs to be
taken into account.
Signed-off-by: NArun Khandavalli <akhandav@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: rebase, fixes, improve commit log]
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Ath10k reports the phy capability that supports P2P_DEVICE interface.

When we use the P2P supported wpa_supplicant to start connection, it'll
create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE
p2p-dev-wlan0 which is for p2p control channel (vdev_id=1).

	ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0
	ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0
	...
	ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1
	ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0

And the txpower in per vif bss_conf will only be set to valid tx power when
the interface is assigned with channel_ctx.

But this P2P_DEVICE interface will never be used for any connection, so
that the uninitialized bss_conf.txpower=0 is assinged to the
arvif->txpower when interface created.

Since the txpower configuration is firmware per physical interface.
So the smallest txpower of all vifs will be the one limit the tx power
of the physical device, that causing the low txpower issue on other
active interfaces.

	wlan0: Limiting TX power to 21 (24 - 3) dBm
	ath10k_pci mac vdev_id 0 txpower 21
	ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0
	ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21
	ath10k_pci mac txpower 0

This issue only happens when we use the wpa_supplicant that supports
P2P or if we use the iw tool to create the control P2P_DEVICE interface.
Signed-off-by: NRyan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k_wmi_tlv_op_pull_fw_stats() uses tb = ath10k_wmi_tlv_parse_alloc(...)
function, which allocates memory. If any of the three error-paths are
taken, this tb needs to be freed.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Align it with the cts protection call.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The cts protection vdev parameter, in new QCA9377 TF2.0 firmware,
requires bss peer to be created for the STATION vdev type.
bss peer is being allocated by the firmware after vdev_start/_up commands.
mac80211 may call the cts protection setup at any time, so the
we needs to track the situation and defer the cts configuration
to prevent firmware asserts, like below:

[00]: 0x05020001 0x000015B3 0x0099ACE2 0x00955B31
[04]: 0x0099ACE2 0x00060730 0x00000004 0x00000000
[08]: 0x0044C754 0x00412C10 0x00000000 0x00409C54
[12]: 0x00000009 0x00000000 0x00952F6C 0x00952F77
[16]: 0x00952CC4 0x00910712 0x00000000 0x00000000
[20]: 0x4099ACE2 0x0040E858 0x00421254 0x004127F4
[24]: 0x8099B9B2 0x0040E8B8 0x00000000 0xC099ACE2
[28]: 0x800B75CB 0x0040E8F8 0x00000007 0x00005008
[32]: 0x809B048A 0x0040E958 0x00000010 0x00433B10
[36]: 0x809AFBBC 0x0040E9A8 0x0042BB74 0x0042BBBC
[40]: 0x8091D252 0x0040E9C8 0x0042BBBC 0x00000001
[44]: 0x809FFA45 0x0040EA78 0x0043D3E4 0x0042C2C8
[48]: 0x809FCEF4 0x0040EA98 0x0043D3E4 0x00000001
[52]: 0x80911210 0x0040EAE8 0x00000010 0x004041D0
[56]: 0x80911154 0x0040EB28 0x00400000 0x00000000
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The correct number for QCA9377 chip is 33 VDEVs.
This impacts also QCA6174 chip and it's max VDEV number.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Similarly to QCA6174, QCA9377 requires the CE5 configuration to be
available for other feature. Use the ath10k_pci_override_ce_config()
for it as well.

This is required for TF2.0 firmware. Previous FW revisions were
working fine without this patch.

Fixes: a70587b3 ("ath10k: configure copy engine 5 for HTT messages")
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA9377 firmware shall alloc 4 IRAM banks
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

'ath10k_htt_tx_free_cont_txbuf' and 'ath10k_htt_tx_free_cont_frag_desc'
have NULL pointer checks to avoid crash if they are called twice
but this is as of now not sufficient as these pointers are not assigned
to NULL once the contiguous DMA memory allocation is freed, fix this.
Though this may not be hit with the explicity check of state variable
'tx_mem_allocated' check, good to have this addressed as well.

Below BUG_ON is hit when the above scenario is simulated
with kernel debugging enabled

 page:f6d09a00 count:0 mapcount:-127 mapping:  (null)
index:0x0
 flags: 0x40000000()
 page dumped because: VM_BUG_ON_PAGE(page_ref_count(page)
== 0)
 ------------[ cut here ]------------
 kernel BUG at ./include/linux/mm.h:445!
 invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
 EIP is at put_page_testzero.part.88+0xd/0xf
 Call Trace:
  [<c118a2cc>] __free_pages+0x3c/0x40
  [<c118a30e>] free_pages+0x3e/0x50
  [<c10222b4>] dma_generic_free_coherent+0x24/0x30
  [<f8c1d9a8>] ath10k_htt_tx_free_cont_txbuf+0xf8/0x140

  [<f8c1e2a9>] ath10k_htt_tx_destroy+0x29/0xa0

  [<f8c143e0>] ath10k_core_destroy+0x60/0x80 [ath10k_core]
  [<f8acd7e9>] ath10k_pci_remove+0x79/0xa0 [ath10k_pci]
  [<c13ed7a8>] pci_device_remove+0x38/0xb0
  [<c14d3492>] __device_release_driver+0x72/0x100
  [<c14d36b7>] driver_detach+0x97/0xa0
  [<c14d29c0>] bus_remove_driver+0x40/0x80
  [<c14d427a>] driver_unregister+0x2a/0x60
  [<c13ec768>] pci_unregister_driver+0x18/0x70
  [<f8aced4f>] ath10k_pci_exit+0xd/0x2be [ath10k_pci]
  [<c1101e78>] SyS_delete_module+0x158/0x210
  [<c11b34f1>] ? __might_fault+0x41/0xa0
  [<c11b353b>] ? __might_fault+0x8b/0xa0
  [<c1001a4b>] do_fast_syscall_32+0x9b/0x1c0
  [<c178da34>] sysenter_past_esp+0x45/0x74
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

These memory chunks are often used as 'swap' by the NIC,
so it will be both reading and writing to these areas.

This seems to fix errors like this on my x86-64 machine:

kernel: DMAR: DMAR:[DMA Write] Request device [05:00.0] fault addr ff5de000
        DMAR:[fault reason 05] PTE Write access is not set
Tested-by: NMarek Behun <kabel@blackhole.sk>
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

With maximum number of vap's configured in a two radio supported
systems of ~256 Mb RAM, doing a continuous wifi down/up and
intermittent traffic streaming from the connected stations results
in failure to allocate contiguous memory for tx buffers. This results
in the disappearance of all VAP's and a manual reboot is needed as
this is not a crash (or) OOM(for OOM killer to be invoked). To address
this allocate contiguous memory for tx buffers one time and re-use them
until the modules are unloaded but this results in a slight increase in
memory footprint of ath10k when the wifi is down, but the modules are
still loaded. Also as of now we use a separate bool 'tx_mem_allocated'
to keep track of the one time memory allocation, as we cannot come up
with something like 'ath10k_tx_{register,unregister}' before
'ath10k_probe_fw' is called as 'ath10k_htt_tx_alloc_cont_frag_desc'
memory allocation is dependent on the hw_param 'continuous_frag_desc'

a) memory footprint of ath10k without the change

lsmod | grep ath10k
ath10k_core           414498  1 ath10k_pci
ath10k_pci             38236  0

b) memory footprint of ath10k with the change

ath10k_core           414980  1 ath10k_pci
ath10k_pci             38236  0

Memory Failure Call trace:

hostapd: page allocation failure: order:6, mode:0xd0
 [<c021f150>] (__dma_alloc_buffer.isra.23) from
[<c021f23c>] (__alloc_remap_buffer.isra.26+0x14/0xb8)
[<c021f23c>] (__alloc_remap_buffer.isra.26) from
[<c021f664>] (__dma_alloc+0x224/0x2b8)
[<c021f664>] (__dma_alloc) from [<c021f810>]
(arm_dma_alloc+0x84/0x90)
[<c021f810>] (arm_dma_alloc) from [<bf954764>]
(ath10k_htt_tx_alloc+0xe0/0x2e4 [ath10k_core])
[<bf954764>] (ath10k_htt_tx_alloc [ath10k_core]) from
[<bf94e6ac>] (ath10k_core_start+0x538/0xcf8 [ath10k_core])
[<bf94e6ac>] (ath10k_core_start [ath10k_core]) from
[<bf947eec>] (ath10k_start+0xbc/0x56c [ath10k_core])
[<bf947eec>] (ath10k_start [ath10k_core]) from
[<bf8a7a04>] (drv_start+0x40/0x5c [mac80211])
[<bf8a7a04>] (drv_start [mac80211]) from [<bf8b7cf8>]
(ieee80211_do_open+0x170/0x82c [mac80211])
[<bf8b7cf8>] (ieee80211_do_open [mac80211]) from
[<c056afc8>] (__dev_open+0xa0/0xf4)
[21053.491752] Normal: 641*4kB (UEMR) 505*8kB (UEMR) 330*16kB (UEMR)
126*32kB (UEMR) 762*64kB (UEMR) 237*128kB (UEMR) 1*256kB (M) 0*512kB
0*1024kB 0*2048kB 0*4096kB = 95276kB
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

During firmware crash (or) user requested manual restart
the system gets into a soft lock up state because of the
below root cause.

During user requested hardware restart / firmware crash
the system goes into a soft lockup state as 'napi_synchronize'
is called after 'napi_disable' (which sets 'NAPI_STATE_SCHED'
bit) and it sleeps into infinite loop as it waits for
'NAPI_STATE_SCHED' to be cleared. This condition is hit because
'ath10k_hif_stop' is called twice as below (resulting in calling
'napi_synchronize' after 'napi_disable')

'ath10k_core_restart' -> 'ath10k_hif_stop' (ATH10K_STATE_ON) ->
-> 'ieee80211_restart_hw' -> 'ath10k_start' -> 'ath10k_halt' ->
'ath10k_core_stop' -> 'ath10k_hif_stop' (ATH10K_STATE_RESTARTING)

Fix this by calling 'ath10k_halt' in ath10k_core_restart itself
as it makes more sense before informing mac80211 to restart h/w
Also remove 'ath10k_halt' in ath10k_start for the state of 'restarting'

Fixes: 3c97f5de ("ath10k: implement NAPI support")
Cc: <stable@vger.kernel.org> # v4.9
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There is a typo bug in the current implementation of
ath10k_wmi_tlv_op_gen_pdev_set_rd.
The conformance test limits are not set up properly.

The two arguments ctl2g and ctl5g were not used at all.
Instead, the regdomain arguments rd2g and rd5g were used
for the ctl settings as well.
Signed-off-by: NErik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In order to receive other BSS entries in mesh mode, Monitor vdev
is created whenever filter flag is set with OTHER_BSS. Recently
it is root caused that setting promisc filter for Mesh interface
is causing performance and stability issues. To fix this issue,
firmware will configure appropriate rxfilters by default for mesh
vdev during vdev creation. This change fixes monitor vdev creation
based on firmware IE
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Per STA tx bitrate info is filled from peer stats.
Export per sta txrate info to cfg80211/nl80211
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Per peer tx stats are part of 'HTT_10_4_T2H_MSG_TYPE_PEER_STATS'
event, Firmware sends one HTT event for every four PPDUs.
HTT payload has success pkts/bytes, failed pkts/bytes, retry
pkts/bytes and rate info per ppdu.
Peer stats are enabled through 'WMI_SERVICE_PEER_STATS',
which are nowadays enabled by default.

Parse peer stats and update the tx rate information per STA.

tx rate, Peer stats are tested on QCA4019 with Firmware version
10.4-3.2.1-00028.
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Command structure and event flow doesn't seem to
be any different compared to existing
implementation for other firmware branches.

This patch effectively adds in-driver support for
spectral scanning on QCA61x4 and QCA9377.

Tested QCA9377 w/ WLAN.TF.1.0-00267-1.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

WMI ops wrappers did not properly check for null
function pointers for spectral scan. This caused
null dereference crash with WMI-TLV based firmware
which doesn't implement spectral scan.

The crash could be triggered with:

  ip link set dev wlan0 up
  echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl

The crash looked like this:

  [  168.031989] BUG: unable to handle kernel NULL pointer dereference at           (null)
  [  168.037406] IP: [<          (null)>]           (null)
  [  168.040395] PGD cdd4067 PUD fa0f067 PMD 0
  [  168.043303] Oops: 0010 [#1] SMP
  [  168.045377] Modules linked in: ath10k_pci(O) ath10k_core(O) ath mac80211 cfg80211 [last unloaded: cfg80211]
  [  168.051560] CPU: 1 PID: 1380 Comm: bash Tainted: G        W  O    4.8.0 #78
  [  168.054336] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
  [  168.059183] task: ffff88000c460c00 task.stack: ffff88000d4bc000
  [  168.061736] RIP: 0010:[<0000000000000000>]  [<          (null)>]           (null)
  ...
  [  168.100620] Call Trace:
  [  168.101910]  [<ffffffffa03b9566>] ? ath10k_spectral_scan_config+0x96/0x200 [ath10k_core]
  [  168.104871]  [<ffffffff811386e2>] ? filemap_fault+0xb2/0x4a0
  [  168.106696]  [<ffffffffa03b97e6>] write_file_spec_scan_ctl+0x116/0x280 [ath10k_core]
  [  168.109618]  [<ffffffff812da3a1>] full_proxy_write+0x51/0x80
  [  168.111443]  [<ffffffff811957b8>] __vfs_write+0x28/0x120
  [  168.113090]  [<ffffffff812f1a2d>] ? security_file_permission+0x3d/0xc0
  [  168.114932]  [<ffffffff8109b912>] ? percpu_down_read+0x12/0x60
  [  168.116680]  [<ffffffff811965f8>] vfs_write+0xb8/0x1a0
  [  168.118293]  [<ffffffff81197966>] SyS_write+0x46/0xa0
  [  168.119912]  [<ffffffff818f2972>] entry_SYSCALL_64_fastpath+0x1a/0xa4
  [  168.121737] Code:  Bad RIP value.
  [  168.123318] RIP  [<          (null)>]           (null)
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Neither of these did the right thing:

- get_tsf just returned 0
- set_tsf assumed a simple offset was applied against
  get_tsf(), which works, except in the case of
  calculating TSF from rx_mactime (actual TSF).

Just remove them for now. We can reimplement set_tsf in
terms of TSF increment/decrement in the future if get_tsf
is ever supported by FW.
Signed-off-by: NThomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Current set_tsf is implemented in terms of TSF_INCREMENT
only. Instead support new WMI command TSF_DECREMENT and
export these through offset_tsf. Advantage is we get
more accurate TSF adjustments, and don't calculate wrong
offset in case absolute TSF was calculated from rx_mactime
(actual TSF).

The new WMI command is available in firmware
10.4-3.2.1-00033 for QCA4019 chips. Old drivers on new
firmware or vice versa shouldn't  be a problem since
get/set tsf logic was already broken.
Signed-off-by: NThomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Indicate hardware (or firmware) supports that CQM packet-loss report
will be generated based on station kickout algorithm. As of now mac80211
tracks connection loss by missing msdu counts (50) whereas ath10k
firmware tracks them by missing ppdus (+ BAR tries). While firmware is
trying to adapt its rate table, mac80211 might send out low_ack event to
hostapd. This is causing frequent connect and disconnect iteration under
noisy environment or when station is roaming around.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The word "background" contains 10 characters so the third argument of
strncmp() need to be 10 in order to match this prefix correctly.
Signed-off-by: NNicolas Iooss <nicolas.iooss_linux@m4x.org>
Fixes: 855aed12 ("ath10k: add spectral scan feature")
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Remove extraneous error message in 'ath10k_htt_tx_alloc_cont_frag_desc'
as the caller 'ath10k_htt_tx_alloc' already dumps a proper error
message
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

cleanup 'ath10k_htt_tx_alloc' by introducing the API's
'ath10k_htt_tx_alloc/free_{cont_txbuf, txdone_fifo} and
re-use them whereever needed
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This partially reverts 'commit 2cdce425
("ath10k: Fix broken NULL func data frame status for 10.4")'
Unfortunately this breaks sending NULL func and the existing
issue of obtaining proper tx status for NULL function will be
fixed. Also update the comments for feature flag added to be
useless and not working

Fixes: 2cdce425 "ath10k: Fix broken NULL func data frame status for
10.4"
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently mac80211 determines whether HW does fragmentation
by checking whether the set_frag_threshold callback is set
or not.
However, some drivers may want to set the HW fragmentation
capability depending on HW generation.
Allow this by checking a HW flag instead of checking the
callback.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
[added the flag to ath10k and wlcore]
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

arvifs list is traversed within data_lock spin_lock in tasklet
context to fill channel information from the corresponding vif.
This means any access to arvifs list for add/del operations
should also be protected with the same spin_lock to avoid the
race. Fix this by performing list add/del on arvfis within the
data_lock. This could fix kernel panic something like the below.

 LR is at ath10k_htt_rx_pktlog_completion_handler+0x100/0xb6c [ath10k_core]
 PC is at ath10k_htt_rx_pktlog_completion_handler+0x1c0/0xb6c [ath10k_core]
 Internal error: Oops: 17 [#1] PREEMPT SMP ARM
 [<bf4857f4>] (ath10k_htt_rx_pktlog_completion_handler+0x2f4/0xb6c [ath10k_core])
 [<bf487540>] (ath10k_htt_txrx_compl_task+0x8b4/0x1188 [ath10k_core])
 [<c00312d4>] (tasklet_action+0x8c/0xec)
 [<c00309a8>] (__do_softirq+0xdc/0x208)
 [<c0030d6c>] (irq_exit+0x84/0xe0)
 [<c005db04>] (__handle_domain_irq+0x80/0xa0)
 [<c00085c4>] (gic_handle_irq+0x38/0x5c)
 [<c0009640>] (__irq_svc+0x40/0x74)

(gdb) list *(ath10k_htt_rx_pktlog_completion_handler+0x1c0)
0x136c0 is in ath10k_htt_rx_h_channel (drivers/net/wireless/ath/ath10k/htt_rx.c:769)
764		struct cfg80211_chan_def def;
765
766		lockdep_assert_held(&ar->data_lock);
767
768		list_for_each_entry(arvif, &ar->arvifs, list) {
769			if (arvif->vdev_id == vdev_id &&
770			    ath10k_mac_vif_chan(arvif->vif, &def) == 0)
771				return def.chan;
772		}
773
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

'ath10k_htt_rx_h_unchain' needs to be called only if the return
value from 'ath10k_htt_rx_amsdu_pop' is 1('chained msdu's'), this
change makes it more explicit and avoids doing a skb_peek, fetching
rx descriptor pointer, checking rx msdu decap format for the case of
ret = 0 (unchained msdus). Found this change during code walk through,
not sure if this addresses any issue.
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Commit 0b8e3c4c ("ath10k: move cal data len to hw_params") broke retrieving
the calibration data from cal_data debugfs file. The length of file was always
zero. The reason is:

    static ssize_t ath10k_debug_cal_data_read(struct file *file,
                                          char __user *user_buf,
                                          size_t count, loff_t *ppos)
    {
        struct ath10k *ar = file->private_data;
        void *buf = file->private_data;

This is obviously bogus, private_data cannot contain both struct ath10k and the
buffer. Fix it by caching calibration data to ar->debug.cal_data. This also
allows it to be accessed when the device is not active (interface is down).

The cal_data buffer is fixed size because during the first firmware probe we
don't yet know what will be the lenght of the calibration data. It was simplest
just to use a fixed length. There's a WARN_ON() in
ath10k_debug_cal_data_fetch() if the buffer is too small.

Tested with qca988x and firmware 10.2.4.70.56.
Reported-by: NNikolay Martynov <mar.kolya@gmail.com>
Fixes: 0b8e3c4c ("ath10k: move cal data len to hw_params")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: NMarty Faltesek <mfaltesek@google.com>
[kvalo@qca.qualcomm.com: improve commit log and minor other changes]
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Unfortunately ath10k does not generally allow modifying the coverage class
with the stock firmware and Qualcomm has so far refused to implement this
feature so that it can be properly supported in ath10k. If we however know
the registers that need to be modified for proper operation with a higher
coverage class, then we can do these modifications from the driver.

This is a hack and might cause subtle problems but as it's not enabled by
default (only when user space changes the coverage class explicitly) it should
not cause new problems for existing setups. But still this should be considered
as an experimental feature and used with caution.

This patch implements the support for first generation cards (QCA9880, QCA9887
and so on) which are based on a core that is similar to ath9k. The registers
are modified in place and need to be re-written every time the firmware sets
them. To achieve this the register status is verified after certain WMI events
from the firmware.

The coverage class may not be modified temporarily right after the card
re-initializes the registers. This is for example the case during scanning.

Thanks to Sebastian Gottschall <s.gottschall@dd-wrt.com> for initially
working on a userspace support for this. This patch wouldn't have been
possible without this documentation.
Signed-off-by: NBenjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This overrides whatever regulatory the device
EEPROM contains and uses what the platform says
instead - in this implementation the ACPI driver.

In case the hint is not programmed or corrupted (0xffff)
the device falls back to the eeprom programmed settings.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
[kvalo@qca.qualcomm.com: remove ifdef, change error handling, change info messages to dbg]
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

During offchannel scan, iw survey dump shows wrong values.
Fix this by assigning cycle counter wranarround type for
QCA9888 and QCA9884, they share same config with QCA4019.
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch helps to get the TPC stats for 10.4 fw variants.
Signed-off-by: NMaharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware is running watchdog timer for tracking copy engine ring index
and write index. Whenever both indices are stuck at same location for
given duration, watchdog will be trigger to assert target. While
updating copy engine destination ring write index, driver ensures that
write index will not be same as read index by finding delta between these
two indices (CE_RING_DELTA).

HTT target to host copy engine (CE5) is special case where ring buffers
will be reused and delta check is not applied while updating write index.
In rare scenario, whenever CE5 ring is full, both indices will be referring
same location and this is causing CE ring stuck issue as explained
above. This issue is originally reported on IPQ4019 during long hour stress
testing and during veriwave max clients testsuites. The same issue is
also observed in other chips as well. Fix this by ensuring that write
index is one less than read index which means that full ring is
available for receiving data.

Cc: stable@vger.kernel.org
Tested-by: NTamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Ignore processing further in SWBA event scheduled for a vif, if mac80211
has marked the particular vif for stop beaconing and brought the vdev
down in 'ath10k_control_beaconing'. This should potentially avoid ath10k
warning/error messages while running continuous wifi down/up with max
number of vaps configured. Found this change during code walk through
and going through other beacon configuration related functions in ath10k
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix to return a negative error code from the error handling case
instead of 0, as done elsewhere in function ath10k_ahb_probe() or
ath10k_ahb_resource_init().
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The (1 << x) - 1 trick won't work when you
are trying to fill up all 64 bits, so add special
case for that.
Signed-off-by: NBen Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: remove the sentence about moving limits]
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

They are not necessarily named in an intuitive manner,
so at least add some comments to help the next person.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>