Update the 4xx board defconfigs
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This updates all the defconfigs in arch/powerpc/configs except iseries
and ps3, which were updated by the preceding commits.

This mostly takes the defaults, except that I turned on tickless idle
and high-resolution timers for everything, and turned off instrumentation
support and "Fair group CPU scheduler" for the smaller/embedded platforms.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch enables the ibm_newemac driver for the Walnut board.  It fixes the
device tree for the walnut board to order the MAL interrupts correctly and
adds the local-mac-address property to the EMAC node.  The bootwrapper is also
updated to extract the MAC address from the OpenBIOS offset where it is stored.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

When checking out the new NO_HZ support in powerpc, I noticed we never
slept for more than 2 seconds.  It turns out SLAB has a 2 second per cpu
timer that causes this.

After switching to SLUB I see some nice 4 second sleeps which is the
limit on this POWER6 box (the decrementer ticks at 512MHz):

slept 4.19 sec
slept 4.19 sec
slept 4.19 sec
slept 4.19 sec
slept 3.96 sec
slept 3.80 sec
slept 2.99 sec

Since SLUB is now the default and some powerpc defconfigs already enable
it, lets enable SLUB across the board for consistency.  While doing this
I also noticed that the maple defconfig has SLAB debugging enabled which
is sure to make your box nice and slow.  Fix that too.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Walnut board defconfig
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch contains a handful of small fixes to allow the Ebony's
flash to be exposed as MTD devices via the physmap_of driver.
Specifically it:
	- Makes a small addition to the device tree and zImage wrapper
to record the correct address for the flash in the device tree based
on the board switches as reported via an FPGA register.
	- Prohibits building the old hard-coded "Ebony" flash map on
arch/powerpc kernels, in favour of using physmap_of's device tree
based approach.
	- Enables MTD and physmap_of in the Ebony defconfig.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds platform support code for the Ebony (440GP) evaluation
board.  This includes both code in arch/powerpc/platforms/44x for
board initialization, and zImage wrapper code to correctly tweak the
flattened device tree based on information from the firmware.  The
zImage supports both IBM OpenBIOS (aka "treeboot") and old versions of
uboot which don't support a flattened device tree.
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Mostly took the defaults, except tried to get the netfilter options
more or less as they were before.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This makes the 8560 evaluation board fully supported under arch/powerpc,
as the first board with CPM2 SoC peripherals. The brand new devicetree
nodes are introduced (intending to be a subset of the QuiccEngine-equipped
models, with dts sources placed into the kernel according to the new convention.

Assuming all the preceding stuff applied (PAL+fs_enet related+ CPM_UART
update), the both TSEC eth ,FCC Eths, and both SCC UARTs are
working. The relevant drivers are still capable to drive users in ppc,
which was verified with 8272ADS (SCC uart+FCC eth).

This is also verified on mpc8540 and actually make it work (PCI stuff
working as well)
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch adds support for 85xx CDS support to arch/powerpc
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

When we build for the MPC8540 ADS produce a uImage by default.
Updated the defconfig to reflect this as well.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Updated patch for support for mpc8540_ads in arch/powerpc with a
flat OF device tree. This patch does not yet support PCI or I2C.
Signed-off-by: NBecky Bruce <becky.bruce@freescale.com>
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Adds support for using the MPC8548 processor on the CDS reference board.
Currently all the major busses (PCI, PCI-X, PCI-Express, sRIO) and eTSEC3
and eTSEC4 are not supported.
Signed-off-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!