Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Helps to know the sta pointer.
Signed-off-by: NBen Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: add %pK and remove the colon]
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When user requests for survey dump data, driver is providing wrong survey
information. This information we sent is the survey data that we have
collected during previous user request.

This issue occurs because we request survey dump for wrong channel. With
this change, we correctly display the correct and current survey
information to userspace.

Fixes: fa7937e3 ("ath10k: update bss channel survey information")
Signed-off-by: NAshok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Trivial fix to spelling mistake in ath10k_warn message.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Older firmware with HTT delivers incorrect tx status for null func
frames to driver, but this fixed in 10.2 and 10.4 firmware versions.
Also this workaround results in reporting of incorrect null func status
for 10.4. Fix this is by introducing a firmware feature flag for 10.4
so that this workaround is skipped and proper tx status for null func
frames are reported
Signed-off-by: NTamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().

The usage pattern of the completion is:

waiter context                          waker context

scan.started
------------

ath10k_start_scan()
  lockdep_assert_held(conf_mutex)
  auth10k_wmi_start_scan()
  wait_for_completion_timeout(scan.started)

					ath10k_wmi_event_scan_start_failed()
					  complete(scan.started)

					ath10k_wmi_event_scan_started()
					  complete(scan.started)

scan.completed
--------------

ath10k_scan_stop()
  lockdep_assert_held(conf_mutex)
  ath10k_wmi_stop_scan()
  wait_for_completion_timeout(scan.completed)

					__ath10k_scan_finish()
					  complete(scan.completed)

scan.on_channel
---------------

ath10k_remain_on_channel()
  mutex_lock(conf_mutex)
  ath10k_start_scan()
  wait_for_completion_timeout(scan.on_channel)

					ath10k_wmi_event_scan_foreign_chan()
					  complete(scan.on_channel)

offchan_tx_completed
--------------------

ath10k_offchan_tx_work()
  mutex_lock(conf_mutex)
  reinit_completion(offchan_tx_completed)
  wait_for_completion_timeout(offchan_tx_completed)

					ath10k_report_offchain_tx()
					  complete(offchan_tx_completed)

install_key_done
----------------
ath10k_install_key()
  lockep_assert_held(conf_mutex)
  reinit_completion(install_key_done)
  wait_for_completion_timeout(install_key_done)

				        ath10k_htt_t2h_msg_handler()
					  complete(install_key_done)

vdev_setup_done
---------------

ath10k_monitor_vdev_start()
  lockdep_assert_held(conf_mutex)
   reinit_completion(vdev_setup_done)
  ath10k_vdev_setup_sync()
    wait_for_completion_timeout(vdev_setup_done)

					ath10k_wmi_event_vdev_start_resp()
					  complete(vdev_setup_done)

ath10k_monitor_vdev_stop()
  lockdep_assert_held(conf_mutex)
  reinit_completion(vdev_setup_done()
  ath10k_vdev_setup_sync()
    wait_for_completion_timeout(vdev_setup_done)

					ath10k_wmi_event_vdev_stopped()
					 complete(vdev_setup_done)

thermal.wmi_sync
----------------
ath10k_thermal_show_temp()
  mutex_lock(conf_mutex)
  reinit_completion(thermal.wmi_sync)
  wait_for_completion_timeout(thermal.wmi_sync)

					ath10k_thermal_event_temperature()
					  complete(thermal.wmi_sync)

bss_survey_done
---------------
ath10k_mac_update_bss_chan_survey
  lockdep_assert_held(conf_mutex)
  reinit_completion(bss_survey_done)
  wait_for_completion_timeout(bss_survey_done)

					ath10k_wmi_event_pdev_bss_chan_info()
					  complete(bss_survey_done)

All complete() calls happen while the conf_mutex is taken. That means
at max one waiter is possible.
Signed-off-by: NDaniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In the wake tx queue path, we are not checking if the frame to be sent
takes management path or not. For eg. QOS null func frame coming here will
take the management path. Since we are not incrementing the descriptor
counter (num_pending_mgmt_tx) w.r.t tx management, on tx completion it is
possible to see negative values.

When the above counter reaches a negative value, we will not be sending a
probe response out.

    if (is_presp &&
	ar->hw_params.max_probe_resp_desc_thres < htt->num_pending_mgmt_tx)

For IPQ4019, max_probe_resp_desc_thres (u32) is 24 is compared against
num_pending_mgmt_tx (int) and the above condtions comes true if the counter
is negative and we drop the probe response.

To avoid this, check on the wake tx queue path as well for the tx path of
the frame and increment the appropriate counters

Fixes: cac08552 "ath10k: move mgmt descriptor limit handle under mgmt_tx"
Signed-off-by: NAshok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

txqs_lock is interfering with wake_tx_queue submitting more frames.
so queues don't get filled in and don't keep firmware/hardware busy
enough. This change helps to reduce the txqs_lock contention and
wake_tx_queue() blockage to being possible in txrx_unref().

To reduce turn around time of wake_tx_queue ops and to maintain fairness
among all txqs, the callback is updated to push first txq alone from
pending list for every wake_tx_queue call. Remaining txqs will be
processed later upon tx completion.

Below improvements are observed in push-only mode and validated on
IPQ4019 platform. With this change, in AP mode ~10Mbps increase is
observed in downlink (AP -> STA) traffic and approx. 5-10% of CPU
usage is reduced.

Major improvement is observed in 1-hop Mesh mode topology in 11ACVHT80.
Compared to Infra mode, CPU overhead is higher in Mesh mode due to path
lookup and no fast-xmit support. So reducing spin lock contention is
helping in Mesh.

             TOT       +change
           --------    --------
TCP DL     545 Mbps    595 Mbps
TCP UL     555 Mbps    585 Mbps
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

With the %pK format specifier we hide the kernel addresses
with the help of kptr_restrict sysctl.
In this patch, %p is changed to %pK in the driver code.

The sysctl is documented in Documentation/sysctl/kernel.txt.
Signed-off-by: NMaharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The use of config_enabled() against config options is ambiguous.  In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED().  Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc.  makes the intention
clearer.

This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.

I noticed two cases where config_enabled() is used against a tristate
option:

 - config_enabled(CONFIG_HWMON)
  [ drivers/net/wireless/ath/ath10k/thermal.c ]

 - config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
  [ drivers/gpu/drm/gma500/opregion.c ]

I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.

Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.comSigned-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NKees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ideally wake_tx_queue should be used regardless as
it is a requirement for reducing bufferbloat and
implementing airtime fairness in the future.

However some setups (typically low-end platforms
hosting QCA988X) suffer performance regressions
with the current wake_tx_queue implementation.
Therefore disable it unless it is really
beneficial with current codebase (which is when
firmware supports smart pull-push tx scheduling).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If WMI and/or firmware has issues removing the peer object,
then we still need to clean up the peer object in the driver.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

just to comply to coding style.
Signed-off-by: NEduardo Abinader <eduardo.abinader@riverbed.com>
Reviewed-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

While debugging OS crashes due to firmware crashes, I enabled
kasan, and it noticed that peer objects were being used-after-freed.

Looks like there are two places we could be leaving stale references
in the peer-map, so clean that up.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Enable support for 'drv_sta_statistics' callback.
Export rx_duration support if available to cfg80211/nl80211

This can also act as a placeholder for any new per STA stats support
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)

TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Disable TX_STBC for both HT and VHT if the devices tx chainmask is '1'
TX_STBC is required only for devices with tx_chainmask > 1. This fixes
a ping failure for QCA9887 (1x1) in HT/VHT mode
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Smatch warns about a number of cases in ath10k where a pointer is
null-checked after it has already been dereferenced, in code involving
ath10k private virtual interface pointers.

Fix these by making the dereference happen later.

Addresses the following smatch warnings:

drivers/net/wireless/ath/ath10k/mac.c:3651 ath10k_mac_txq_init() warn: variable dereferenced before check 'txq' (see line 3649)
drivers/net/wireless/ath/ath10k/mac.c:3664 ath10k_mac_txq_unref() warn: variable dereferenced before check 'txq' (see line 3659)
drivers/net/wireless/ath/ath10k/htt_tx.c:70 __ath10k_htt_tx_txq_recalc() warn: variable dereferenced before check 'txq->sta' (see line 52)
drivers/net/wireless/ath/ath10k/htt_tx.c:740 ath10k_htt_tx_get_vdev_id() warn: variable dereferenced before check 'cb->vif' (see line 736)
drivers/net/wireless/ath/ath10k/txrx.c:86 ath10k_txrx_tx_unref() warn: variable dereferenced before check 'txq' (see line 84)
drivers/net/wireless/ath/ath10k/wmi.c:1837 ath10k_wmi_op_gen_mgmt_tx() warn: variable dereferenced before check 'cb->vif' (see line 1825)
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

CCK hardware table mapping from QCA99X0 onwards got revised.
The CCK hardware rate values are in a proper order wrt. to
rate and preamble as below

ATH10K_HW_RATE_REV2_CCK_LP_1M = 1,
ATH10K_HW_RATE_REV2_CCK_LP_2M = 2,
ATH10K_HW_RATE_REV2_CCK_LP_5_5M = 3,
ATH10K_HW_RATE_REV2_CCK_LP_11M = 4,
ATH10K_HW_RATE_REV2_CCK_SP_2M = 5,
ATH10K_HW_RATE_REV2_CCK_SP_5_5M = 6,
ATH10K_HW_RATE_REV2_CCK_SP_11M = 7,

This results in reporting of rx frames (with CCK rates)
totally wrong for QCA99X0, QCA4019. Fix this by having
separate CCK rate table for these chipsets with rev2 suffix
and registering the correct rate mapping to mac80211 based on
the new hw_param (introduced) 'cck_rate_map_rev2' which shall
be true for any newchipsets from QCA99X0 onwards
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

We must not attempt to send WMI packets while holding the data-lock,
as it may deadlock:

BUG: sleeping function called from invalid context at drivers/net/wireless/ath/ath10k/wmi.c:1824
in_atomic(): 1, irqs_disabled(): 0, pid: 2878, name: wpa_supplicant

=============================================
[ INFO: possible recursive locking detected ]
4.4.6+ #21 Tainted: G        W  O
---------------------------------------------
wpa_supplicant/2878 is trying to acquire lock:
 (&(&ar->data_lock)->rlock){+.-...}, at: [<ffffffffa0721511>] ath10k_wmi_tx_beacons_iter+0x26/0x11a [ath10k_core]

but task is already holding lock:
 (&(&ar->data_lock)->rlock){+.-...}, at: [<ffffffffa070251b>] ath10k_peer_create+0x122/0x1ae [ath10k_core]

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&(&ar->data_lock)->rlock);
  lock(&(&ar->data_lock)->rlock);

 *** DEADLOCK ***

 May be due to missing lock nesting notation

4 locks held by wpa_supplicant/2878:
 #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff816493ca>] rtnl_lock+0x12/0x14
 #1:  (&ar->conf_mutex){+.+.+.}, at: [<ffffffffa0706932>] ath10k_add_interface+0x3b/0xbda [ath10k_core]
 #2:  (&(&ar->data_lock)->rlock){+.-...}, at: [<ffffffffa070251b>] ath10k_peer_create+0x122/0x1ae [ath10k_core]
 #3:  (rcu_read_lock){......}, at: [<ffffffffa062f304>] rcu_read_lock+0x0/0x66 [mac80211]

stack backtrace:
CPU: 3 PID: 2878 Comm: wpa_supplicant Tainted: G        W  O    4.4.6+ #21
Hardware name: To be filled by O.E.M. To be filled by O.E.M./ChiefRiver, BIOS 4.6.5 06/07/2013
 0000000000000000 ffff8801fcadf8f0 ffffffff8137086d ffffffff82681720
 ffffffff82681720 ffff8801fcadf9b0 ffffffff8112e3be ffff8801fcadf920
 0000000100000000 ffffffff82681720 ffffffffa0721500 ffff8801fcb8d348
Call Trace:
 [<ffffffff8137086d>] dump_stack+0x81/0xb6
 [<ffffffff8112e3be>] __lock_acquire+0xc5b/0xde7
 [<ffffffffa0721500>] ? ath10k_wmi_tx_beacons_iter+0x15/0x11a [ath10k_core]
 [<ffffffff8112d0d0>] ? mark_lock+0x24/0x201
 [<ffffffff8112e908>] lock_acquire+0x132/0x1cb
 [<ffffffff8112e908>] ? lock_acquire+0x132/0x1cb
 [<ffffffffa0721511>] ? ath10k_wmi_tx_beacons_iter+0x26/0x11a [ath10k_core]
 [<ffffffffa07214eb>] ? ath10k_wmi_cmd_send_nowait+0x1ce/0x1ce [ath10k_core]
 [<ffffffff816f9e2b>] _raw_spin_lock_bh+0x31/0x40
 [<ffffffffa0721511>] ? ath10k_wmi_tx_beacons_iter+0x26/0x11a [ath10k_core]
 [<ffffffffa0721511>] ath10k_wmi_tx_beacons_iter+0x26/0x11a [ath10k_core]
 [<ffffffffa07214eb>] ? ath10k_wmi_cmd_send_nowait+0x1ce/0x1ce [ath10k_core]
 [<ffffffffa062eb18>] __iterate_interfaces+0x9d/0x13d [mac80211]
 [<ffffffffa062f609>] ieee80211_iterate_active_interfaces_atomic+0x32/0x3e [mac80211]
 [<ffffffffa07214eb>] ? ath10k_wmi_cmd_send_nowait+0x1ce/0x1ce [ath10k_core]
 [<ffffffffa071fa9f>] ath10k_wmi_tx_beacons_nowait.isra.13+0x14/0x16 [ath10k_core]
 [<ffffffffa0721676>] ath10k_wmi_cmd_send+0x71/0x242 [ath10k_core]
 [<ffffffffa07023f6>] ath10k_wmi_peer_delete+0x3f/0x42 [ath10k_core]
 [<ffffffffa0702557>] ath10k_peer_create+0x15e/0x1ae [ath10k_core]
 [<ffffffffa0707004>] ath10k_add_interface+0x70d/0xbda [ath10k_core]
 [<ffffffffa05fffcc>] drv_add_interface+0x123/0x1a5 [mac80211]
 [<ffffffffa061554b>] ieee80211_do_open+0x351/0x667 [mac80211]
 [<ffffffffa06158aa>] ieee80211_open+0x49/0x4c [mac80211]
 [<ffffffff8163ecf9>] __dev_open+0x88/0xde
 [<ffffffff8163ef6e>] __dev_change_flags+0xa4/0x13a
 [<ffffffff8163f023>] dev_change_flags+0x1f/0x54
 [<ffffffff816a5532>] devinet_ioctl+0x2b9/0x5c9
 [<ffffffff816514dd>] ? copy_to_user+0x32/0x38
 [<ffffffff816a6115>] inet_ioctl+0x81/0x9d
 [<ffffffff816a6115>] ? inet_ioctl+0x81/0x9d
 [<ffffffff81621cf8>] sock_do_ioctl+0x20/0x3d
 [<ffffffff816223c4>] sock_ioctl+0x222/0x22e
 [<ffffffff8121cf95>] do_vfs_ioctl+0x453/0x4d7
 [<ffffffff81625603>] ? __sys_recvmsg+0x4c/0x5b
 [<ffffffff81225af1>] ? __fget_light+0x48/0x6c
 [<ffffffff8121d06b>] SyS_ioctl+0x52/0x74
 [<ffffffff816fa736>] entry_SYSCALL_64_fastpath+0x16/0x7a
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 firmware has support to enable or disable btcoex functionality
without reloading firmware via wmi pdev param. Add provision to send
pdev param command via existing btcoex knob.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Recent changes revolving around implementing
wake_tx_queue support introduced a significant
performance regressions on some (slower, uni-proc)
systems.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

During hw scan, firmware sends two channel information events (pre-
complete, complete) to host for each channel change. The snap shot of cycle
counters (rx_clear and total) between these two events are given for
survey dump. In order to get latest survey statistics of all channels, a
scan request has to be issued. In general, an AP DUT is brought up, it
won't leave BSS channel except few cases like overlapping bss or radar
detection. So survey statistics of bss channel is always referring to
older data that are collected before starting AP (either ACS/OBSS scan).

To collect latest survey information from target, firmware provides WMI
interface to read cycle counters from hardware. For each survey dump
request, BSS channel cycle counters are read and cleared in hardware.
This makes sure that behavior is in align with ath9k survey report.
So survey dump always gives snap shot of cycle counters b/w two survey
requests.
Signed-off-by: NYanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

According to the spec, VHT doesn't exist in 2.4GHz.

There are vendor extensions to allow a subset of VHT to work
(notably 256-QAM), but since mac80211 doesn't support those
advertising VHT capability on 2.4GHz leads to the behaviour
of reporting VHT capabilities but not being able to use any
of them due to mac80211's code requiring 80 MHz support.

Remove the VHT capabilities from 2.4GHz for now. If mac80211
gets extended to use the (likely Broadcom) vendor IEs for it
and handles the lack of 80 MHz support, it can be added back.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

fix a typo (spelling mistake) in 'ath10k_start'
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Preparation for testmode.c to use ath10k_core_fetch_board_data_api_n().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Preparation for testmode.c to use ath10k_core_fetch_board_data_api_n().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Preparation for testmode.c to use ath10k_core_fetch_board_data_api_n().
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To make it easier to share ath10k_core_fetch_board_data_api_n() with testmode.c
refactor all firmware components to struct ath10k_fw_components. This structure
will hold firmware related files, for example firmware-N.bin and board-N.bin.

For firmware-N.bin create a new struct ath10k_fw_file which contains the actual
firmware image as well as the parsed data from the image.

Modify ath10k_core_start() to take struct ath10k_fw_components() as an argument
which makes it possible in following patches to drop some ugly hacks from
testmode.c.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

push-pull mode needs certain amount the host driver involvement for
managing queues in the host memory and packet delivery to firmware.
qca4019 wifi firmware has an option to stay in push mode for less
number of active traffic flow and then switch to push-pull mode when
the active traffic flow goes beyond the certain limit.

The advantage of staying in push mode for less active traffic is, the
host cpu consumption is reduced. qca4019 firmware supports this
flexibility of the mode switch. It takes the host driver interest
(LOW_PERF/HIGH_PERF) via WMI_EXT_RESOURCE_CFG_CMDID,

 LOW_PERF  - fw would stay in push mode and switch to push-pull
               based on demand.
 HIGH_PERF - fw would stay in push-pull mode from the boot.

To make this configuration generic, new WMI services
WMI_SERVICE_TX_MODE_PUSH_ONLY, WMI_SERVICE_TX_MODE_PUSH_PULL,
WMI_SERVICE_TX_MODE_DYNAMIC are introduced to take dynamic tx mode
switch support availability in firmware.
Based on WMI_SERVICE_TX_MODE_DYNAMIC, LOW_PERF or HIGHT_PERF is
configured to the firmware.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NTamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Upon firmware assert, restart work will be triggered so that mac80211
will reconfigure the driver. An issue is reported that after restart
work, survey dump data do not contain in-use (SURVEY_INFO_IN_USE) info
for operating channel. During reconfigure, since mac80211 already has
valid channel context for given radio, channel context iteration return
num_chanctx > 0. Hence rx_channel is always NULL. Fix this by assigning
channel context to rx_channel when driver restart is in progress.

Cc: stable@vger.kernel.org
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Found by checkpatch:

drivers/net/wireless/ath/ath10k/mac.c:6800: Alignment should match open parent
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

drivers/net/wireless/ath/ath10k/mac.c:452: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
drivers/net/wireless/ath/ath10k/mac.c:455: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
drivers/net/wireless/ath/ath10k/txrx.c:133: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix checkpatch warnings about use of spaces with operators:

spaces preferred around that '*' (ctx:VxV)

This has been recently added to checkpatch.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.2.4.70.24 firmware introduces new feature to set TSF
via vdev parameter, hence implement relevant function.
set_tsf function can be used to shift TBTT that will
help avoid its clockdrift which happens when beacons
are collided.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

qca99x0 and qca4019 solutions limit probe responses transmissions.
Logging warning message for each probe response drop is flooding
kernel log unnecessary with " failed to increase tx mgmt pending
count: -16, dropping". Hence reducing log level to debug.
Reported-by: NSebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Provide a debugfs entry to enable/ disable Peer Stats feature.
Peer Stats feature is for developers/users who are more interested
in studying in Rx/Tx stats with multiple clients connected, hence
disable this by default. Enabling this feature by default results
in unneccessary processing of Peer Stats event for every 500ms
and updating peer_stats list (allocating memory) and cleaning it up
ifexceeds the higher limit and this can be an unnecessary overhead
during long run stress testing.
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This prevents tx hangs or hiccups if pull-push
supporting firmware defines per-txq thresholds or
switches modes dynamically.

Fixes: 29946878 ("ath10k: implement wake_tx_queue")
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The wake_tx_queue/push_pending logic had a bug
which could stop queues indefinitely effectivelly
breaking traffic.

Fixes: 29946878 ("ath10k: implement wake_tx_queue")
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>