Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
大约 1 年 前同步成功

通知 153
Star 36
Fork 7
cloud-kernel
cloud-kernel

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 07 6月, 2017 5 次提交
  3. 01 6月, 2017 5 次提交
  5. 30 5月, 2017 2 次提交
  7. 27 5月, 2017 1 次提交
    • J
      KVM: x86: Fix virtual wire mode · 52b54190
      由 Jan H. Schönherr 提交于 
      Intel SDM says, that at most one LAPIC should be configured with ExtINT
delivery. KVM configures all LAPICs this way. This causes pic_unlock()
to kick the first available vCPU from the internal KVM data structures.
If this vCPU is not the BSP, but some not-yet-booted AP, the BSP may
never realize that there is an interrupt.

Fix that by enabling ExtINT delivery only for the BSP.

This allows booting a Linux guest without a TSC in the above situation.
Otherwise the BSP gets stuck in calibrate_delay_converge().
Signed-off-by: NJan H. Schönherr <jschoenh@amazon.de>
Reviewed-by: NWanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      52b54190
  9. 26 5月, 2017 2 次提交
    • J
      KVM: nVMX: Fix handling of lmsw instruction · e1d39b17
      由 Jan H. Schönherr 提交于 
      The decision whether or not to exit from L2 to L1 on an lmsw instruction is
based on bogus values: instead of using the information encoded within the
exit qualification, it uses the data also used for the mov-to-cr
instruction, which boils down to using whatever is in %eax at that point.

Use the correct values instead.

Without this fix, an L1 may not get notified when a 32-bit Linux L2
switches its secondary CPUs to protected mode; the L1 is only notified on
the next modification of CR0. This short time window poses a problem, when
there is some other reason to exit to L1 in between. Then, L2 will be
resumed in real mode and chaos ensues.
Signed-off-by: NJan H. Schönherr <jschoenh@amazon.de>
Reviewed-by: NWanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      e1d39b17
    • W
      KVM: X86: Fix preempt the preemption timer cancel · 5acc1ca4
      由 Wanpeng Li 提交于 
      Preemption can occur during cancel preemption timer, and there will be
inconsistent status in lapic, vmx and vmcs field.

          CPU0                    CPU1

  preemption timer vmexit
  handle_preemption_timer(vCPU0)
    kvm_lapic_expired_hv_timer
      vmx_cancel_hv_timer
        vmx->hv_deadline_tsc = -1
        vmcs_clear_bits
        /* hv_timer_in_use still true */
  sched_out
                           sched_in
                           kvm_arch_vcpu_load
                             vmx_set_hv_timer
                               write vmx->hv_deadline_tsc
                               vmcs_set_bits
                           /* back in kvm_lapic_expired_hv_timer */
                           hv_timer_in_use = false
                           ...
                           vmx_vcpu_run
                             vmx_arm_hv_run
                               write preemption timer deadline
                             spurious preemption timer vmexit
                               handle_preemption_timer(vCPU0)
                                 kvm_lapic_expired_hv_timer
                                   WARN_ON(!apic->lapic_timer.hv_timer_in_use);

This can be reproduced sporadically during boot of L2 on a
preemptible L1, causing a splat on L1.

 WARNING: CPU: 3 PID: 1952 at arch/x86/kvm/lapic.c:1529 kvm_lapic_expired_hv_timer+0xb5/0xd0 [kvm]
 CPU: 3 PID: 1952 Comm: qemu-system-x86 Not tainted 4.12.0-rc1+ #24 RIP: 0010:kvm_lapic_expired_hv_timer+0xb5/0xd0 [kvm]
  Call Trace:
  handle_preemption_timer+0xe/0x20 [kvm_intel]
  vmx_handle_exit+0xc9/0x15f0 [kvm_intel]
  ? lock_acquire+0xdb/0x250
  ? lock_acquire+0xdb/0x250
  ? kvm_arch_vcpu_ioctl_run+0xdf3/0x1ce0 [kvm]
  kvm_arch_vcpu_ioctl_run+0xe55/0x1ce0 [kvm]
  kvm_vcpu_ioctl+0x384/0x7b0 [kvm]
  ? kvm_vcpu_ioctl+0x384/0x7b0 [kvm]
  ? __fget+0xf3/0x210
  do_vfs_ioctl+0xa4/0x700
  ? __fget+0x114/0x210
  SyS_ioctl+0x79/0x90
  do_syscall_64+0x8f/0x750
  ? trace_hardirqs_on_thunk+0x1a/0x1c
  entry_SYSCALL64_slow_path+0x25/0x25

This patch fixes it by disabling preemption while cancelling
preemption timer.  This way cancel_hv_timer is atomic with
respect to kvm_arch_vcpu_load.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      5acc1ca4
  11. 22 5月, 2017 4 次提交
    • L
      x86: fix 32-bit case of __get_user_asm_u64() · 33c9e972
      由 Linus Torvalds 提交于 
      The code to fetch a 64-bit value from user space was entirely buggered,
and has been since the code was merged in early 2016 in commit
b2f68038 ("x86/mm/32: Add support for 64-bit __get_user() on 32-bit
kernels").

Happily the buggered routine is almost certainly entirely unused, since
the normal way to access user space memory is just with the non-inlined
"get_user()", and the inlined version didn't even historically exist.

The normal "get_user()" case is handled by external hand-written asm in
arch/x86/lib/getuser.S that doesn't have either of these issues.

There were two independent bugs in __get_user_asm_u64():

 - it still did the STAC/CLAC user space access marking, even though
   that is now done by the wrapper macros, see commit 11f1a4b9
   ("x86: reorganize SMAP handling in user space accesses").

   This didn't result in a semantic error, it just means that the
   inlined optimized version was hugely less efficient than the
   allegedly slower standard version, since the CLAC/STAC overhead is
   quite high on modern Intel CPU's.

 - the double register %eax/%edx was marked as an output, but the %eax
   part of it was touched early in the asm, and could thus clobber other
   inputs to the asm that gcc didn't expect it to touch.

   In particular, that meant that the generated code could look like
   this:

        mov    (%eax),%eax
        mov    0x4(%eax),%edx

   where the load of %edx obviously was _supposed_ to be from the 32-bit
   word that followed the source of %eax, but because %eax was
   overwritten by the first instruction, the source of %edx was
   basically random garbage.

The fixes are trivial: remove the extraneous STAC/CLAC entries, and mark
the 64-bit output as early-clobber to let gcc know that no inputs should
alias with the output register.

Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@kernel.org   # v4.8+
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      33c9e972
    • L
      Clean up x86 unsafe_get/put_user() type handling · 334a023e
      由 Linus Torvalds 提交于 
      Al noticed that unsafe_put_user() had type problems, and fixed them in
commit a7cc722f ("fix unsafe_put_user()"), which made me look more
at those functions.

It turns out that unsafe_get_user() had a type issue too: it limited the
largest size of the type it could handle to "unsigned long".  Which is
fine with the current users, but doesn't match our existing normal
get_user() semantics, which can also handle "u64" even when that does
not fit in a long.

While at it, also clean up the type cast in unsafe_put_user().  We
actually want to just make it an assignment to the expected type of the
pointer, because we actually do want warnings from types that don't
convert silently.  And it makes the code more readable by not having
that one very long and complex line.

[ This patch might become stable material if we ever end up back-porting
  any new users of the unsafe uaccess code, but as things stand now this
  doesn't matter for any current existing uses. ]

Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      334a023e
    • A
      osf_wait4(): fix infoleak · a8c39544
      由 Al Viro 提交于 
      failing sys_wait4() won't fill struct rusage...

Cc: stable@vger.kernel.org
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
      a8c39544
    • A
      fix unsafe_put_user() · a7cc722f
      由 Al Viro 提交于 
      __put_user_size() relies upon its first argument having the same type as what
the second one points to; the only other user makes sure of that and
unsafe_put_user() should do the same.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
      a7cc722f
  13. 20 5月, 2017 5 次提交
    • R
      KVM: x86: prevent uninitialized variable warning in check_svme() · 92ceb767
      由 Radim Krčmář 提交于 
      get_msr() of MSR_EFER is currently always going to succeed, but static
checker doesn't see that far.

Don't complicate stuff and just use 0 for the fallback -- it means that
the feature is not present.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
      92ceb767
    • R
      KVM: x86/vPMU: fix undefined shift in intel_pmu_refresh() · 34b0dadb
      由 Radim Krčmář 提交于 
      Static analysis noticed that pmu->nr_arch_gp_counters can be 32
(INTEL_PMC_MAX_GENERIC) and therefore cannot be used to shift 'int'.

I didn't add BUILD_BUG_ON for it as we have a better checker.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Fixes: 25462f7f ("KVM: x86/vPMU: Define kvm_pmu_ops to support vPMU function dispatch")
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
      34b0dadb
    • R
      KVM: x86: zero base3 of unusable segments · f0367ee1
      由 Radim Krčmář 提交于 
      Static checker noticed that base3 could be used uninitialized if the
segment was not present (useable).  Random stack values probably would
not pass VMCS entry checks.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Fixes: 1aa36616 ("KVM: x86 emulator: consolidate segment accessors")
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NDavid Hildenbrand <david@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
      f0367ee1
    • W
      KVM: X86: Fix read out-of-bounds vulnerability in kvm pio emulation · cbfc6c91
      由 Wanpeng Li 提交于 
      Huawei folks reported a read out-of-bounds vulnerability in kvm pio emulation.

- "inb" instruction to access PIT Mod/Command register (ioport 0x43, write only,
  a read should be ignored) in guest can get a random number.
- "rep insb" instruction to access PIT register port 0x43 can control memcpy()
  in emulator_pio_in_emulated() to copy max 0x400 bytes but only read 1 bytes,
  which will disclose the unimportant kernel memory in host but no crash.

The similar test program below can reproduce the read out-of-bounds vulnerability:

void hexdump(void *mem, unsigned int len)
{
        unsigned int i, j;

        for(i = 0; i < len + ((len % HEXDUMP_COLS) ? (HEXDUMP_COLS - len % HEXDUMP_COLS) : 0); i++)
        {
                /* print offset */
                if(i % HEXDUMP_COLS == 0)
                {
                        printf("0x%06x: ", i);
                }

                /* print hex data */
                if(i < len)
                {
                        printf("%02x ", 0xFF & ((char*)mem)[i]);
                }
                else /* end of block, just aligning for ASCII dump */
                {
                        printf("   ");
                }

                /* print ASCII dump */
                if(i % HEXDUMP_COLS == (HEXDUMP_COLS - 1))
                {
                        for(j = i - (HEXDUMP_COLS - 1); j <= i; j++)
                        {
                                if(j >= len) /* end of block, not really printing */
                                {
                                        putchar(' ');
                                }
                                else if(isprint(((char*)mem)[j])) /* printable char */
                                {
                                        putchar(0xFF & ((char*)mem)[j]);
                                }
                                else /* other char */
                                {
                                        putchar('.');
                                }
                        }
                        putchar('\n');
                }
        }
}

int main(void)
{
	int i;
	if (iopl(3))
	{
		err(1, "set iopl unsuccessfully\n");
		return -1;
	}
	static char buf[0x40];

	/* test ioport 0x40,0x41,0x42,0x43,0x44,0x45 */

	memset(buf, 0xab, sizeof(buf));

	asm volatile("push %rdi;");
	asm volatile("mov %0, %%rdi;"::"q"(buf));

	asm volatile ("mov $0x40, %rdx;");
	asm volatile ("in %dx,%al;");
	asm volatile ("stosb;");

	asm volatile ("mov $0x41, %rdx;");
	asm volatile ("in %dx,%al;");
	asm volatile ("stosb;");

	asm volatile ("mov $0x42, %rdx;");
	asm volatile ("in %dx,%al;");
	asm volatile ("stosb;");

	asm volatile ("mov $0x43, %rdx;");
	asm volatile ("in %dx,%al;");
	asm volatile ("stosb;");

	asm volatile ("mov $0x44, %rdx;");
	asm volatile ("in %dx,%al;");
	asm volatile ("stosb;");

	asm volatile ("mov $0x45, %rdx;");
	asm volatile ("in %dx,%al;");
	asm volatile ("stosb;");

	asm volatile ("pop %rdi;");
	hexdump(buf, 0x40);

	printf("\n");

	/* ins port 0x40 */

	memset(buf, 0xab, sizeof(buf));

	asm volatile("push %rdi;");
	asm volatile("mov %0, %%rdi;"::"q"(buf));

	asm volatile ("mov $0x20, %rcx;");
	asm volatile ("mov $0x40, %rdx;");
	asm volatile ("rep insb;");

	asm volatile ("pop %rdi;");
	hexdump(buf, 0x40);

	printf("\n");

	/* ins port 0x43 */

	memset(buf, 0xab, sizeof(buf));

	asm volatile("push %rdi;");
	asm volatile("mov %0, %%rdi;"::"q"(buf));

	asm volatile ("mov $0x20, %rcx;");
	asm volatile ("mov $0x43, %rdx;");
	asm volatile ("rep insb;");

	asm volatile ("pop %rdi;");
	hexdump(buf, 0x40);

	printf("\n");
	return 0;
}

The vcpu->arch.pio_data buffer is used by both in/out instrutions emulation
w/o clear after using which results in some random datas are left over in
the buffer. Guest reads port 0x43 will be ignored since it is write only,
however, the function kernel_pio() can't distigush this ignore from successfully
reads data from device's ioport. There is no new data fill the buffer from
port 0x43, however, emulator_pio_in_emulated() will copy the stale data in
the buffer to the guest unconditionally. This patch fixes it by clearing the
buffer before in instruction emulation to avoid to grant guest the stale data
in the buffer.

In addition, string I/O is not supported for in kernel device. So there is no
iteration to read ioport %RCX times for string I/O. The function kernel_pio()
just reads one round, and then copy the io size * %RCX to the guest unconditionally,
actually it copies the one round ioport data w/ other random datas which are left
over in the vcpu->arch.pio_data buffer to the guest. This patch fixes it by
introducing the string I/O support for in kernel device in order to grant the right
ioport datas to the guest.

Before the patch:

0x000000: fe 38 93 93 ff ff ab ab .8......
0x000008: ab ab ab ab ab ab ab ab ........
0x000010: ab ab ab ab ab ab ab ab ........
0x000018: ab ab ab ab ab ab ab ab ........
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........

0x000000: f6 00 00 00 00 00 00 00 ........
0x000008: 00 00 00 00 00 00 00 00 ........
0x000010: 00 00 00 00 4d 51 30 30 ....MQ00
0x000018: 30 30 20 33 20 20 20 20 00 3
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........

0x000000: f6 00 00 00 00 00 00 00 ........
0x000008: 00 00 00 00 00 00 00 00 ........
0x000010: 00 00 00 00 4d 51 30 30 ....MQ00
0x000018: 30 30 20 33 20 20 20 20 00 3
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........

After the patch:

0x000000: 1e 02 f8 00 ff ff ab ab ........
0x000008: ab ab ab ab ab ab ab ab ........
0x000010: ab ab ab ab ab ab ab ab ........
0x000018: ab ab ab ab ab ab ab ab ........
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........

0x000000: d2 e2 d2 df d2 db d2 d7 ........
0x000008: d2 d3 d2 cf d2 cb d2 c7 ........
0x000010: d2 c4 d2 c0 d2 bc d2 b8 ........
0x000018: d2 b4 d2 b0 d2 ac d2 a8 ........
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........

0x000000: 00 00 00 00 00 00 00 00 ........
0x000008: 00 00 00 00 00 00 00 00 ........
0x000010: 00 00 00 00 00 00 00 00 ........
0x000018: 00 00 00 00 00 00 00 00 ........
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........
Reported-by: NMoguofang <moguofang@huawei.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Moguofang <moguofang@huawei.com>
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
      cbfc6c91
    • W
      KVM: x86: Fix potential preemption when get the current kvmclock timestamp · e2c2206a
      由 Wanpeng Li 提交于 
       BUG: using __this_cpu_read() in preemptible [00000000] code: qemu-system-x86/2809
 caller is __this_cpu_preempt_check+0x13/0x20
 CPU: 2 PID: 2809 Comm: qemu-system-x86 Not tainted 4.11.0+ #13
 Call Trace:
  dump_stack+0x99/0xce
  check_preemption_disabled+0xf5/0x100
  __this_cpu_preempt_check+0x13/0x20
  get_kvmclock_ns+0x6f/0x110 [kvm]
  get_time_ref_counter+0x5d/0x80 [kvm]
  kvm_hv_process_stimers+0x2a1/0x8a0 [kvm]
  ? kvm_hv_process_stimers+0x2a1/0x8a0 [kvm]
  ? kvm_arch_vcpu_ioctl_run+0xac9/0x1ce0 [kvm]
  kvm_arch_vcpu_ioctl_run+0x5bf/0x1ce0 [kvm]
  kvm_vcpu_ioctl+0x384/0x7b0 [kvm]
  ? kvm_vcpu_ioctl+0x384/0x7b0 [kvm]
  ? __fget+0xf3/0x210
  do_vfs_ioctl+0xa4/0x700
  ? __fget+0x114/0x210
  SyS_ioctl+0x79/0x90
  entry_SYSCALL_64_fastpath+0x23/0xc2
 RIP: 0033:0x7f9d164ed357
  ? __this_cpu_preempt_check+0x13/0x20

This can be reproduced by run kvm-unit-tests/hyperv_stimer.flat w/
CONFIG_PREEMPT and CONFIG_DEBUG_PREEMPT enabled.

Safe access to per-CPU data requires a couple of constraints, though: the
thread working with the data cannot be preempted and it cannot be migrated
while it manipulates per-CPU variables. If the thread is preempted, the
thread that replaces it could try to work with the same variables; migration
to another CPU could also cause confusion. However there is no preemption
disable when reads host per-CPU tsc rate to calculate the current kvmclock
timestamp.

This patch fixes it by utilizing get_cpu/put_cpu pair to guarantee both
__this_cpu_read() and rdtsc() are not preempted.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
      e2c2206a
  15. 19 5月, 2017 9 次提交
    • A
      arm64: dts: rockchip: fix include reference · 6bf1c2d2
      由 Arnd Bergmann 提交于 
      The way we handle include paths for DT has changed a bit, which
broke a file that had an unconventional way to reference a common
header file:

arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts:47:10: fatal error: include/dt-bindings/input/linux-event-codes.h: No such file or directory

This removes the leading "include/" from the path name, which fixes it.

Fixes: d5d332d3 ("devicetree: Move include prefixes from arch to separate directory")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
      6bf1c2d2
    • A
      ARM: remove duplicate 'const' annotations' · 0527873b
      由 Arnd Bergmann 提交于 
      gcc-7 warns about some declarations that are more 'const' than necessary:

arch/arm/mach-at91/pm.c:338:34: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
 static const struct of_device_id const ramc_ids[] __initconst = {
arch/arm/mach-bcm/bcm_kona_smc.c:36:34: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
 static const struct of_device_id const bcm_kona_smc_ids[] __initconst = {
arch/arm/mach-spear/time.c:207:34: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
 static const struct of_device_id const timer_of_match[] __initconst = {
arch/arm/mach-omap2/prm_common.c:714:34: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
 static const struct of_device_id const omap_prcm_dt_match_table[] __initconst = {
arch/arm/mach-omap2/vc.c:562:35: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
 static const struct i2c_init_data const omap4_i2c_timing_data[] __initconst = {

The ones in arch/arm were apparently all introduced accidentally by one
commit that correctly marked a lot of variables as __initconst.

Fixes: 19c233b7 ("ARM: appropriate __init annotation for const data")
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NKrzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
      0527873b
    • R
      arm64: defconfig: enable options needed for QCom DB410c board · f4e506c5
      由 Rob Herring 提交于 
      Enable Qualcomm drivers needed to boot Dragonboard 410c with HDMI. This
enables support for clocks, regulators, and USB PHY.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: NRob Herring <robh@kernel.org>
[Olof: Turned off _RPM configs per follow-up email]
Signed-off-by: NOlof Johansson <olof@lixom.net>
      f4e506c5
    • R
      arm64: defconfig: sync with savedefconfig · eb1e6716
      由 Rob Herring 提交于 
      Sync the defconfig with savedefconfig as config options change/move over
time.

Generated with the following commands:
make defconfig
make savedefconfig
cp defconfig arch/arm64/configs/defconfig
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>
      eb1e6716
    • L
      ARM: configs: add a gemini defconfig · 877dd4b1
      由 Linus Walleij 提交于 
      It makes sense to have a stripped-down defconfig for just Gemini, as
it is a pretty small platform used in NAS etc, and will use appended
device tree. It is also quick to compile and test. Hopefully this
defconfig can be a good base for distributions such as OpenWRT.

I plan to add in the config options needed for the different
variants of Gemini as we go along.

Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>
      877dd4b1
    • O
      devicetree: Move include prefixes from arch to separate directory · d5d332d3
      由 Olof Johansson 提交于 
      We use a directory under arch/$ARCH/boot/dts as an include path
that has links outside of the subtree to find dt-bindings from under
include/dt-bindings. That's been working well, but new DT architectures
haven't been adding them by default.

Recently there's been a desire to share some of the DT material between
arm and arm64, which originally caused developers to create symlinks or
relative includes between the subtrees. This isn't ideal -- it breaks
if the DT files aren't stored in the exact same hierarchy as the kernel
tree, and generally it's just icky.

As a somewhat cleaner solution we decided to add a $ARCH/ prefix link
once, and allow DTS files to reference dtsi (and dts) files in other
architectures that way.

Original approach was to create these links under each architecture,
but it lead to the problem of recursive symlinks.

As a remedy, move the include link directories out of the architecture
trees into a common location. At the same time, they can now share one
directory and one dt-bindings/ link as well.

Fixes: 4027494a ('ARM: dts: add arm/arm64 include symlinks')
Reported-by: NRussell King <linux@armlinux.org.uk>
Reported-by: NOmar Sandoval <osandov@osandov.com>
Reviewed-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NRob Herring <robh@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: linux-arch <linux-arch@vger.kernel.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>
      d5d332d3
    • J
      xen: make xen_flush_tlb_all() static · c71e6d80
      由 Juergen Gross 提交于 
      xen_flush_tlb_all() is used in arch/x86/xen/mmu.c only. Make it static.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: NJuergen Gross <jgross@suse.com>
      c71e6d80
    • J
      xen: cleanup pvh leftovers from pv-only sources · 989513a7
      由 Juergen Gross 提交于 
      There are some leftovers testing for pvh guest mode in pv-only source
files. Remove them.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: NJuergen Gross <jgross@suse.com>
      989513a7
    • M
      powerpc/mm: Fix virt_addr_valid() etc. on 64-bit hash · e41e53cd
      由 Michael Ellerman 提交于 
      virt_addr_valid() is supposed to tell you if it's OK to call virt_to_page() on
an address. What this means in practice is that it should only return true for
addresses in the linear mapping which are backed by a valid PFN.

We are failing to properly check that the address is in the linear mapping,
because virt_to_pfn() will return a valid looking PFN for more or less any
address. That bug is actually caused by __pa(), used in virt_to_pfn().

eg: __pa(0xc000000000010000) = 0x10000  # Good
    __pa(0xd000000000010000) = 0x10000  # Bad!
    __pa(0x0000000000010000) = 0x10000  # Bad!

This started happening after commit bdbc29c1 ("powerpc: Work around gcc
miscompilation of __pa() on 64-bit") (Aug 2013), where we changed the definition
of __pa() to work around a GCC bug. Prior to that we subtracted PAGE_OFFSET from
the value passed to __pa(), meaning __pa() of a 0xd or 0x0 address would give
you something bogus back.

Until we can verify if that GCC bug is no longer an issue, or come up with
another solution, this commit does the minimal fix to make virt_addr_valid()
work, by explicitly checking that the address is in the linear mapping region.

Fixes: bdbc29c1 ("powerpc: Work around gcc miscompilation of __pa() on 64-bit")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Reviewed-by: NPaul Mackerras <paulus@ozlabs.org>
Reviewed-by: NBalbir Singh <bsingharora@gmail.com>
Tested-by: NBreno Leitao <breno.leitao@gmail.com>
      e41e53cd
  17. 18 5月, 2017 5 次提交
    • D
      KVM: Silence underflow warning in avic_get_physical_id_entry() · d3e7dec0
      由 Dan Carpenter 提交于 
      Smatch complains that we check cap the upper bound of "index" but don't
check for negatives.  It's a false positive because "index" is never
negative.  But it's also simple enough to make it unsigned which makes
the code easier to audit.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
      d3e7dec0
    • L
      sparc/ftrace: Fix ftrace graph time measurement · 48078d2d
      由 Liam R. Howlett 提交于 
      The ftrace function_graph time measurements of a given function is not
accurate according to those recorded by ftrace using the function
filters.  This change pulls the x86_64 fix from 'commit 722b3c74
("ftrace/graph: Trace function entry before updating index")' into the
sparc specific prepare_ftrace_return which stops ftrace from
counting interrupted tasks in the time measurement.

Example measurements for select_task_rq_fair running "hackbench 100
process 1000":

              |  tracing/trace_stat/function0  |  function_graph
 Before patch |  2.802 us                      |  4.255 us
 After patch  |  2.749 us                      |  3.094 us
Signed-off-by: NLiam R. Howlett <Liam.Howlett@Oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      48078d2d
    • O
      sparc: Fix -Wstringop-overflow warning · deba804c
      由 Orlando Arias 提交于 
      Greetings,

GCC 7 introduced the -Wstringop-overflow flag to detect buffer overflows
in calls to string handling functions [1][2]. Due to the way
``empty_zero_page'' is declared in arch/sparc/include/setup.h, this
causes a warning to trigger at compile time in the function mem_init(),
which is subsequently converted to an error. The ensuing patch fixes
this issue and aligns the declaration of empty_zero_page to that of
other architectures. Thank you.

Cheers,
Orlando.

[1] https://gcc.gnu.org/ml/gcc-patches/2016-10/msg02308.html
[2] https://gcc.gnu.org/gcc-7/changes.htmlSigned-off-by: NOrlando Arias <oarias@knights.ucf.edu>

--------------------------------------------------------------------------------
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      deba804c
    • N
      sparc64: Fix mapping of 64k pages with MAP_FIXED · b6c41cb0
      由 Nitin Gupta 提交于 
      An incorrect huge page alignment check caused
mmap failure for 64K pages when MAP_FIXED is used
with address not aligned to HPAGE_SIZE.

Orabug: 25885991

Fixes: dcd1912d ("sparc64: Add 64K page size support")
Signed-off-by: NNitin Gupta <nitin.m.gupta@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b6c41cb0
    • M
      arm64/cpufeature: don't use mutex in bringup path · 63a1e1c9
      由 Mark Rutland 提交于 
      Currently, cpus_set_cap() calls static_branch_enable_cpuslocked(), which
must take the jump_label mutex.

We call cpus_set_cap() in the secondary bringup path, from the idle
thread where interrupts are disabled. Taking a mutex in this path "is a
NONO" regardless of whether it's contended, and something we must avoid.
We didn't spot this until recently, as ___might_sleep() won't warn for
this case until all CPUs have been brought up.

This patch avoids taking the mutex in the secondary bringup path. The
poking of static keys is deferred until enable_cpu_capabilities(), which
runs in a suitable context on the boot CPU. To account for the static
keys being set later, cpus_have_const_cap() is updated to use another
static key to check whether the const cap keys have been initialised,
falling back to the caps bitmap until this is the case.

This means that users of cpus_have_const_cap() gain should only gain a
single additional NOP in the fast path once the const caps are
initialised, but should always see the current cap value.

The hyp code should never dereference the caps array, since the caps are
initialized before we run the module initcall to initialise hyp. A check
is added to the hyp init code to document this requirement.

This change will sidestep a number of issues when the upcoming hotplug
locking rework is merged.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Reviewed-by: NMarc Zyniger <marc.zyngier@arm.com>
Reviewed-by: NSuzuki Poulose <suzuki.poulose@arm.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Sewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
      63a1e1c9
  19. 17 5月, 2017 2 次提交
    • R
      ARM: dts: dra7: Reduce cpu thermal shutdown temperature · bca52388
      由 Ravikumar Kattekola 提交于 
      On dra7, as per TRM, the HW shutdown (TSHUT) temperature is hardcoded
to 123C and cannot be modified by SW. This means when the temperature
reaches 123C HW asserts TSHUT output which signals a warm reset.
This reset is held until the temperature goes below the TSHUT low (105C).

While in SW, the thermal driver continuously monitors current temperature
and takes decisions based on whether it reached an alert or a critical point.
The intention of setting a SW critical point is to prevent force reset by HW
and instead do an orderly_poweroff(). But if the SW critical temperature is
greater than or equal to that of HW then it defeats the purpose. To address
this and let SW take action before HW does keep the SW critical temperature
less than HW TSHUT value.

The value for SW critical temperature was chosen as 120C just to ensure
we give SW sometime before HW catches up.

Document reference
SPRUI30C – DRA75x, DRA74x Technical Reference Manual - November 2016
SPRUHZ6H - AM572x Technical Reference Manual - November 2016

Tested on:
DRA75x PG 2.0 Rev H EVM
Signed-off-by: NRavikumar Kattekola <rk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      bca52388
    • M
      powerpc/mm: Fix crash in page table dump with huge pages · bfb9956a
      由 Michael Ellerman 提交于 
      The page table dump code doesn't know about huge pages, so currently
it crashes (or walks random memory, usually leading to a crash), if it
finds a huge page. On Book3S we only see huge pages in the Linux page
tables when we're using the P9 Radix MMU.

Teaching the code to properly handle huge pages is a bit more involved,
so for now just prevent the crash.

Cc: stable@vger.kernel.org # v4.10+
Fixes: 8eb07b18 ("powerpc/mm: Dump linux pagetables")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      bfb9956a