- 13 7月, 2008 6 次提交
-
-
由 Eric Miao 提交于
IRQ trigger type can be specified in the IRQ resource definition by IORESOURCE_IRQ_*, we need only one way to specify this. This also fixes the following small issue: To allow dynamic support for multiple platforms, when those relevant macros are not defined for one specific platform, the default case will be: - SMC_DYNAMIC_BUS_CONFIG defined - and SMC_IRQ_FLAGS = IRQF_TRIGGER_RISING While if "irq_flags" is missing when defining the smc91x_platdata, usually as follows: static struct smc91x_platdata xxxx_smc91x_data = { .flags = SMC91X_USE_XXBIT, }; The lp->cfg.irq_flags will always be overriden by the above structure (due to a memcpy), thus rendering lp->cfg.irq_flags to be "0" always. (regardless of the default SMC_IRQ_FLAGS or IORESOURCE_IRQ_* flags) Fixes this by forcing to use IORESOURCE_IRQ_* flags if present, and make the only user of smc91x_platdata.irq_flags (renesas/migor) to use IORESOURCE_IRQ_*. Signed-off-by: NEric Miao <eric.miao@marvell.com> Acked-by: NNicolas Pitre <nico@cam.org> Acked-by: NJeff Garzik <jgarzik@pobox.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
-
由 Dmitry Baryshkov 提交于
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Conflicts: arch/arm/mach-pxa/Makefile
-
由 Russell King 提交于
Conflicts: arch/arm/mach-pxa/Kconfig arch/arm/mach-pxa/tosa.c arch/arm/mach-pxa/spitz.c
-
由 Russell King 提交于
Conflicts: MAINTAINERS
-
- 11 7月, 2008 11 次提交
-
-
由 Ian Molton 提交于
Signed-off-by: NIan Molton <spyro@f2s.com>
-
由 Ian Molton 提交于
Signed-off-by: NIAn Molton <spyro@f2s.com>
-
由 Ian Molton 提交于
Signed-off-by: NIan Molton <spyro@f2s.com>
-
由 Ian Molton 提交于
Signed-off-by: NIan Molton <spyro@f2s.com>
-
由 Ian Molton 提交于
Signed-off-by: NIan Molton <spyro@f2s.com>
-
由 Ian Molton 提交于
-
由 Russell King 提交于
-
由 Mark Brown 提交于
Also add some white space for a little clarity. Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Mark Brown 提交于
It's not been updated in quite some time and we now have git for history. Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Mark Brown 提交于
pdev is used later on by dev_printk() so must be set. Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Mark Brown 提交于
Callers may stop the SSP core requesting the interrupt so it can't be freed unconditionally. Also use NO_IRQ like we should. Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 10 7月, 2008 23 次提交
-
-
由 Stefan Schmidt 提交于
This defconfig enables all currently available features. It also builds one zImage which runs on all machines. Signed-off-by: NAntonio Ospite <ao2@openezx.org> Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Stefan Schmidt 提交于
Common code for the different EZX GSM phones. Functions to control framebuffer, backlight power, OHCI and UART init. Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com> Acked-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Stefan Schmidt 提交于
Maintainer entries for the Motorola EZX GSM mobile phones. Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com> Acked-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Stefan Schmidt 提交于
Allow choosing the bits in UP2OCR_SEOS. Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com> Acked-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Stefan Schmidt 提交于
Add the .depth field to pxafb_mode_info and use it to set pixel data format as 18(RGB666), 19(RGBT666), 24(RGB888) or 25(RGBT888) Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com> Acked-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Stefan Schmidt 提交于
Add missing depth definitions to LCCR3. Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com> Acked-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Marek Vašut 提交于
This patch adds battery monitoring driver for PalmTX. It can read voltage from the battery and temperature. It also monitors charging/discharging status. Signed-off-by: NMarek Vasut <marek.vasut@gmail.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Marek Vašut 提交于
This patch adds PCMCIA support for PalmTX handheld computer. There is one chip hard-soldered to slot0, another slot is not in use and not accessible. Signed-off-by: NMarek Vasut <marek.vasut@gmail.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Marek Vašut 提交于
PalmTX is PXA27x based device with wifi, bluetooth, touchscreen, sdio slot, irda, keypad, nand flash, pxa framebuffer, serial and usb gadget interface. Supported by this patch is pxafb, touchscreen, irda, keypad and sdio slot. Signed-off-by: NMarek Vasut <marek.vasut@gmail.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Ian Molton 提交于
This patch uses the ability of PXA's clocklib to alias clock to resolve the problem caused by sharing the SA1111 IO controller between PXA and SA1100 architectures, which have differing GPIO numbering. Signed-off-by: NIan Molton <spyro@f2s.com>
-
由 Ian Molton 提交于
Signed-off-by: NIan Molton <spyro@f2s.com>
-
由 Ian Molton 提交于
PXA255 and 26x are the only PXA CPUs with HWUART. This patch prevents bogus initialisation on other models. Signed-off-by: NIan Molton <spyro@f2s.com>
-
由 Eric Miao 提交于
The initial patch from Lothar, and Lennert make it into a cleaner one, modified and tested on PXA320 by Eric Miao. This patch moves the L2 cache operations out of proc-xsc3.S into dedicated outer cache support code. CACHE_XSC3L2 can be deselected so no L2 cache specific code will be linked in, and that L2 enable bit will not be set, this applies to the following cases: a. _only_ PXA300/PXA310 support included and no L2 cache wanted b. PXA320 support included, but want L2 be disabled So the enabling of L2 depends on two things: - CACHE_XSC3L2 is selected - and L2 cache is present Where the latter is only a safeguard (previous testing shows it works OK even when this bit is turned on). IXP series of processors with XScale3 cannot disable L2 cache for the moment since they depend on the L2 cache for its coherent memory, so IXP may always select CACHE_XSC3L2. Other L2 relevant bits are always turned on (i.e. the original code enclosed by #if L2_CACHE_ENABLED .. #endif), as they showed no side effects. Specifically, these bits are: - OC bits in TTBASE register (table walk outer cache attributes) - LLR Outer Cache Attributes (OC) in Auxiliary Control Register Signed-off-by: NLothar WaÃ<9f>mann <LW@KARO-electronics.de> Signed-off-by: NLennert Buytenhek <buytenh@marvell.com> Signed-off-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Eric Miao 提交于
Signed-off-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Eric Miao 提交于
And also reserve 32 IRQs for the two GPIO expanders. Signed-off-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Eric Miao 提交于
Signed-off-by: NEric Miao <eric.miao@marvell.com> Cc: Sergey Podstavin <spodstavin@ru.mvista.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Eric Miao 提交于
Signed-off-by: NEric Miao <eric.miao@marvell.com> Cc: Sergey Podstavin <spodstavin@ru.mvista.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Eric Miao 提交于
A pxa3xx_set_nand_info() is also introduced to set the PXA3xx NAND driver specific platform_data structure pointer. Signed-off-by: NEric Miao <eric.miao@marvell.com> Cc: Sergey Podstavin <spodstavin@ru.mvista.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Eric Miao 提交于
Signed-off-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 eric miao 提交于
So processor specific clock sources can be defined in pxa300.c and pxa320.c. Signed-off-by: Neric miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Eric Miao 提交于
Some boards want to change low power state of pins on-the-fly, this function helps to facilitate that operation instead of switching back-n-forth between two configurations with pxa2xx_mfp_config(). Signed-off-by: NEric Miao <eric.miao@marvell.com> Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Eric Miao 提交于
Signed-off-by: NEric Miao <eric.miao@marvell.com> Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Eric Miao 提交于
pxa320_init_mfp() is simple enough to be embedded into pxa320_init() to simplify the code a bit. Signed-off-by: NEric Miao <eric.miao@marvell.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-