Add support for handling write zeroes command on target.
Call into __blkdev_issue_zeroout, which the block layer expands into the
best suitable variant of zeroing the LBAs. Allow write zeroes operation
to deallocate the LBAs when calling __blkdev_issue_zeroout.
Signed-off-by: NChaitanya Kulkarni <chaitanya.kulkarni@hgst.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Allow write zeroes operations (REQ_OP_WRITE_ZEROES) on the block
device, if the device supports optional command bit set for write
zeroes. Add support to setup write zeroes command. Set maximum possible
write zeroes sectors in one write zeroes command according to
nvme write zeroes command definition.
Signed-off-by: NChaitanya Kulkarni <chaitanya.kulkarni@hgst.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Add the command structure, optional command set support (ONCS) bit and
a new error code for the Write Zeroes command.
Signed-off-by: NChaitanya Kulkarni <chaitanya.kulkarni@hgst.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

This adds a new block layer operation to zero out a range of
LBAs. This allows to implement zeroing for devices that don't use
either discard with a predictable zero pattern or WRITE SAME of zeroes.
The prominent example of that is NVMe with the Write Zeroes command,
but in the future, this should also help with improving the way
zeroing discards work. For this operation, suitable entry is exported in
sysfs which indicate the number of maximum bytes allowed in one
write zeroes operation by the device.
Signed-off-by: NChaitanya Kulkarni <chaitanya.kulkarni@hgst.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Similar to __blkdev_issue_discard this variant allows submitting
the final bio asynchronously and chaining multiple ranges
into a single completion.
Signed-off-by: NChaitanya Kulkarni <chaitanya.kulkarni@hgst.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

Both blkdev_report_zones and blkdev_reset_zones can operate on a partition of
a zoned block device. However, the first and last zones reported for a
partition make sense only if the partition start sector and size are aligned
on the device zone size. The same applies for zone reset. Resetting the first
or the last zone of a partition straddling zones may impact neighboring
partitions. Finally, if a partition start sector is not at the beginning of a
sequential zone, it will be impossible to write to the first sectors of the
partition on a host-managed device.
Avoid all these problems and incoherencies by ignoring partitions that are not
zone aligned.

Note: Even with CONFIG_BLK_DEV_ZONED disabled, bdev_is_zoned() will report the
correct disk zoning type (host-aware, host-managed or none) but
bdev_zone_size() will always return 0 for zoned block devices (i.e. the zone
size is unknown). So test this as a way to ensure that a zoned block device is
being handled as such. As a result, for a host-aware devices, unaligned zone
partitions will be accepted with CONFIG_BLK_DEV_ZONED disabled. That is, the
disk will be treated as a regular block device (as it should). If zoned block
device support is enabled, only aligned partitions will be accepted.
Signed-off-by: NDamien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Since targets are given a virtual target device, it is necessary to
translate all communication between targets and the backend device.
Implement the translation layer for get/set bad block table.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

On target-specific operations pass on nvm_tgt_dev instead of the generic
nvm device.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Target devices do not have access to the device driver operations.
Introduce a helper function that exposes the max. number of physical
sectors supported by the underlying device.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Avoid calling media manager and device-specific operations directly from
rrpc. Create helper functions on lightnvm's core instead.
Signed-off-by: NJavier González <javier@cnexlabs.com>

Made it work with null_blk as well.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

In order to naturally support multi-target instances on an Open-Channel
SSD, targets should own the LUNs they get blocks from and manage
provisioning internally. This is done in several steps.

Since targets own the LUNs the are instantiated on top of and manage the
free block list internally, there is no need for a LUN abstraction in
the media manager. LUNs are intrinsically managed as in the physical
layout (ch:0,lun:0, ..., ch:0,lun:n, ch:1,lun:0, ch:1,lun:n, ...,
ch:m,lun:0, ch:m,lun:n) and given to the targets based on the target
creation ioctl. This simplifies LUN management and clears the path for a
partition manager to sit directly underneath LightNVM targets.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

In order to naturally support multi-target instances on an Open-Channel
SSD, targets should own the LUNs they get blocks from and manage
provisioning internally. This is done in several steps.

A part of this transformation is that targets manage their blocks
internally. This patch eliminates the nvm_block abstraction and moves
block management to the target logic. The rrpc target is transformed.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Since LUNs are managed internally on targets, the media manager has no
access to the free LUN lists. Thus, debug functions that show LUN
information on the device should not be implemented on the media
manager, but rather on the target in itself.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Since LUNs are managed internally on the target, there is no need for
the media manager to implement a get_lun operation.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

In order to naturally support multi-target instances on an Open-Channel
SSD, targets should own the LUNs they get blocks from and manage
provisioning internally. This is done in several steps.

This patch moves the block provisioning inside of the target and removes
the get/put block interface from the media manager.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

LUNs are exclusively owned by targets implementing a block device FTL.
Doing this reservation requires at the moment a 2-way callback gennvm
<-> target. The reason behind this is that LUNs were not assumed to
always be exclusively owned by targets. However, this design decision
goes against I/O determinism QoS (two targets would mix I/O on the same
parallel unit in the device).

This patch makes LUN reservation as part of the target creation on the
media manager. This makes that LUNs are always exclusively owned by the
target instantiated on top of them. LUN stripping and/or sharing should
be implemented on the target itself or the layers on top.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

The gen_lun abstraction in the generic media manager was conceived on
the assumption that a single target would instantiated on top of it.
This has complicated target design to implement multi-instances. Remove
this abstraction and move its logic to nvm_lun, which manages physical
lun geometry and operations.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

There is a constant to refer to free blocks. Use it when marking bad
blocks instead of using a constant value
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Before vectored I/Os were supported on rrpc, the physical address was
stored as part of the nvm_rqd request. This variable become obsolete
when the ppa_list was introduced. Cleanup this variable.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Targets are assumed to used the same generic ppa format, where the
address is partitioned on ch:lun:block:pg:pl:sec. Thus, make the
function in charge of transforming the ppa address from a linear format
to the generic one available to all targets.

This function will be needed by the media manager in order to do target
mapping translations when targets are divided on different physical
partitions.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Cleanup definition leftovers from old gennvm interface
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

LightNVM used to be managed and configured through sysfs. Since the
introduction of management ioctls this interface is redundant and
outdated. Get rid of it.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

rrpc cannot handle bios of size > 256kb due to NVMe using a 64 bit
bitmap to signal I/O completion. If a larger bio comes, split it
explicitly.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Add ECC error codes to enable the appropriate handling in the target.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Bad blocks should be managed by block owners. This would be either
targets for data blocks or sysblk for system blocks.

In order to support this, export two functions: One to mark a block as
an specific type (e.g., bad block) and another to update the bad block
table on the device.

Move bad block management to rrpc.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Device blocks should be marked by the device and considered as bad
blocks by the media manager. Thus, do not make assumptions on which
blocks are going to be used by the device. In doing so we might lose
valid blocks from the free list.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Erases might be subject to host hints. An example is multi-plane
programming to erase blocks in parallel. Enable targets to specify this
hint.
Signed-off-by: NJavier González <javier@cnexlabs.com>
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

Previously, LBA read and write were not supported in the lightnvm
specification. Now that it supports it, lets use the traditional
NVMe gendisk, and attach the lightnvm sysfs geometry export.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

When struct nvme_request was introduced, the nvme_nvm_submit_io was
converted to the new interface. The interface moves nvme_nvm_command
data structure into the struct request pdu. On io completion, rq->cmd is
freed, which should have been the dereferenced pdu nvme_request->cmd.

Fixes: d49187e9 "nvme: introduce struct nvme_request"
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

After commit 287922eb ("block: defer timeouts to a workqueue"),
deleting the timeout work after freezing the queue shouldn't be
necessary, since the synchronization is already enforced by the
acquisition of a q_usage_counter reference in blk_mq_timeout_work.
Signed-off-by: NGabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Reviewed-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Currently there's no way to enable wbt if it's not enabled in the
kernel config by default for a device. Allow a write to the
'wbt_lat_usec' queue sysfs file to enable wbt.

This is useful for both the kernel config case, but also if the
device is CFQ managed and it was turned off by default.
Signed-off-by: NJens Axboe <axboe@fb.com>

Make it clear that we are disabling wbt for the specified queued,
if it was enabled by default. This is in preparation for allowing
users to re-enable wbt, and not have it disabled automatically
again.
Signed-off-by: NJens Axboe <axboe@fb.com>

Allow a write of '-1' to reset the default latency target for
a given device. This removes knowledge of the different default
settings for rotational vs non-rotational from user space.
Signed-off-by: NJens Axboe <axboe@fb.com>

Multiple paths don't set it properly, ensure that we do.

Fixes: 9561a7ad ("nbd: add multi-connection support")
Signed-off-by: NJens Axboe <axboe@fb.com>

Bit #7 is already used, move to bit #8 which is the first unused
one.

Fixes: 9561a7ad ("nbd: add multi-connection support")
Signed-off-by: NJens Axboe <axboe@fb.com>

NBD can become contended on its single connection.  We have to serialize all
writes and we can only process one read response at a time.  Fix this by
allowing userspace to provide multiple connections to a single nbd device.  This
coupled with block-mq drastically increases performance in multi-process cases.
Thanks,
Signed-off-by: NJosef Bacik <jbacik@fb.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

blkcg allocates some per-cgroup data structures with GFP_NOWAIT and
when that fails falls back to operations which aren't specific to the
cgroup.  Occassional failures are expected under pressure and falling
back to non-cgroup operation is the right thing to do.

Unfortunately, I forgot to add __GFP_NOWARN to these allocations and
these expected failures end up creating a lot of noise.  Add
__GFP_NOWARN.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NMarc MERLIN <marc@merlins.org>
Reported-by: NVlastimil Babka <vbabka@suse.cz>
Signed-off-by: NJens Axboe <axboe@fb.com>

The check on bio->bi_vcnt doesn't make sense in erase_end_io().
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Also code gets simplified a bit.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Also this patch simplify the code a bit.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NJens Axboe <axboe@fb.com>