The new RV2P firmware fixes 2 issues:

1. The jumbo rx buffer page size is now configurable and set to the
   proper PAGE_SIZE.  Before, it was assumed to be always 4K.

2. Driver sometimes would crash when receiving jumbo packets mixed
   with firmware management packets.  This was caused by the old
   firmware DMA'ing to the wrong address.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should zero out the context memory for 5709 before each reset.  When
we resume after suspend for example, the memory may not be zero and the
chip may not function correctly.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The register BNX2_CTX_STATUS (0x1004) should be skipped on 5709 as it
contains reserved bits.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some remote PHY blade systems, the driver receives no initial link
interrupt.  As a result, the GMII/MII MAC mode does not get setup properly.
To fix this problem, we add an initial poll of the link state after chip
reset.

With this change, the setting of the initial carrier state in the init
code can be eliminated.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2_set_remote_link() should be called under bp->phy_lock to protect
against concurrent polling and interrupt calls.  This change is needed
by the next patch which will add one initial poll of the remote PHY
link status.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The forwarding table binary interface (my bad choice), only exposes
the port number of the first 8 bits. The bridge code was limited to
256 ports at the time, but now the kernel supports up 1024 ports, so
the upper bits are lost when doing:

   brctl showmacs

The fix is to squeeze the extra bits into small hole left in data
structure, to maintain binary compatiablity.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the version number to 3.92.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All variants of the 5714, 5715, and 5780 offer a feature called the
"Universal Management Port".  This feature is implemented in firmware
and is largely transparent to the driver, except...

It turns out that the UMP firmware needs to know the current status
of the link.  Because the firmware cannot touch the PHY registers while
the driver is in control of the device, it needs the driver to report
link status changes through an additional handshaking mechanism.
Without this handshake, it has been observed in the field that the UMP
firmware will not operate correctly.

This patch implements the new handshake with the UMP firmware.  Since
the handshake uses the same mechanism ASF heartbeats use, code was
added to detect and wait for completion of a pending previous event.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A CPMU related loopback test bug existed for AX revisions of the 5761.
While that errata has been fixed, the CPMU still slows down the core
clock too far to run the loopback test successfully.  This patch
disables the CPMU LINK_SPEED mode just like we do with the AX
revisions of the 5761 and all revisions of the 5784.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5761 NVRAM sizes assigned to the nvram_size member are half as big
as they should be.  This patch corrects the NVRAM sizes and replaces
the hardcoded constants with preprocessor constants for readability.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MI clock is not configured correctly on adapters with the CPMU
present.  The tg3 driver has code which statically sets the MI clock to
be a fraction of the speed at which the core clock is running.
However, the CPMU can change the adapter's core clock frequency based
on operating conditions.  Consequently, the MI will run slow when the
core's clock has been slowed down.

There is a new 500KHz constant frequency clock available on adapters
with a CPMU.  This patch removes the static core clock scaling and
configures the MI clock to use this new 500KHz clock instead.

Running the MI clock at slower speeds will not directly result in data
corruption, but it does challenge the PHY read and write routine timeouts.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If someone tries to _urb_unlink while _urb_queue_head is running, he'll see
_urb->queue == NULL and fail to do any locking.  Prevent that from happening
by strategically placed barriers.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Makes the intention of the nested min/max clear.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the fixed size channels[NR_CPUS] array in net/core/dev.c and
dynamically allocate array based on nr_cpu_ids.
Signed-off-by: NMike Travis <travis@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

WARN_ON_ONCE() gives a stack trace including the full module list.
Having this in the kernel dump for the timeout case in the
generic netdev watchdog will help us see quicker which driver
is involved. It also allows us to collect statistics 
and patterns in terms of which drivers have this event occuring.

Suggested by Andrew Morton
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One finds all kinds of crazy things with some shell pipelining.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this unfortunate case, proc_mkdir_mode wrapper can't be used anymore and
this is no way to reuse proc_create_data due to nlinks assignment. So,
copy the code from proc_mkdir and assign PDE->data at the appropriate
moment.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace proc_net_fops_create with proc_create_data.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace create_proc_entry with specially created for this purpose proc_create.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check for PDE->data != NULL becomes useless after the replacement
of proc_net_fops_create with proc_create_data.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simply replace proc_create and further data assigned with proc_create_data.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simply replace proc_create and further data assigned with proc_create_data.
proc_atm_dev_ops holds proper referrence.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simply replace proc_create and further data assigned with proc_create_data.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simply replace proc_create and further data assigned with proc_create_data.
Additionally, there is no need to assign NULL to PDE->data after creation,
/proc generic has already done this for us.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simply replace proc_create and further data assigned with proc_create_data.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simply replace proc_create and further data assigned with proc_create_data.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was an obvious typo in LED structure
initialization which caused the radio and quality/activity
leds to be incorrectly initialized which resulted in
the leds not being enabled.

Additionally add the rt2x00led_led_activity() handler
that will enable TX/RX activity leds when the radio
is being enabled.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The timing settings for 1MBs should exclude
the short preamble bit since that only applies
to 2MBs, 5.5MBs and 11MBs.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NKirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

direct_mask will be set when we are not associated and requesting a
direct scan. The second debug print will be confusing as priv->essid
is not set at that time and it will thus print "<hidden>" while it is
known to which AP a direct scan is requested - as previous debug message
also indicates.

Now make all debugging consistent.
Signed-off-by: NBill Moss <bmoss@clemson.edu>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All channels should be scanned, including the current channel
when the client is associated.

Removed also unused flag to scan only active channels.
Signed-off-by: NGuy Cohen <guy.cohen@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes some TX/RX related locking issues.
With this patch applied, some of the PHY transmission errors are fixed.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/8390.c:37:2: warning: returning void-valued expression
drivers/net/bnx2.c:1635:3: warning: returning void-valued expression
drivers/net/xen-netfront.c:1806:2: warning: returning void-valued expression
net/ipv4/tcp_hybla.c:105:3: warning: returning void-valued expression
net/ipv4/tcp_vegas.c:171:3: warning: returning void-valued expression
net/ipv4/tcp_veno.c:123:3: warning: returning void-valued expression
net/sysctl_net.c:85:2: warning: returning void-valued expression
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(which is autogenerated by kbuild)
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  ipv6: Compilation fix for compat MCAST_MSFILTER sockopts.