This chip supports Energy Efficient Ethernet.  The existing code only
supports a smaller set of devices with 5718 PCI ID.  Expand support for
all devices with the same 5717 B0 chip ID.
Signed-off-by: NMichael Chan <mchan@broadocm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch also adds a couple of fixes

 - For the 57766 and non Ax versions of 57765, bootcode needs to setup
   the PCIE Fast Training Sequence (FTS) value to prevent transmit hangs.
   Unfortunately, it does not have enough room in the selfboot case (i.e.
   devices with no NVRAM).  The driver needs to implement this.

 - For performance reasons, the 2k DMA engine mode on the 57766 should
   be enabled and dma size limited to 2k for standard sized packets.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BCM4785 or sometimes named BMC4705 is a Broadcom SoC which a
Gigabit 5750 Ethernet core. The core is connected via PCI with the rest
of the SoC, but it uses some extension.

This core does not use a firmware or an eeprom.

Some devices only have a switch which supports 100MBit/s, this
currently does not work with this driver.

This patch was original written by Michael Buesch <m@bues.ch> and is in
OpenWrt for some years now.

This was tested on a Linksys WRT610N V1 and older versions of this patch
were tested by other people on different devices.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In OpenWrt we currently use a switch driver which uses the ioctls to
configure the switch in the phy. We have to provide the phy_id to do
so, but without this patch this is not possible.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc failures already get standardized OOM
messages and a dump_stack.

Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TG3_PHY_AUXCTL_SMDSP_ENABLE/DISABLE macros do a blind write to the phy
auxiliary control register and overwrite the EXT_PKT_LEN (bit 14) resulting
in intermittent crc errors on jumbo frames with some link partners. Change
the code to do a read/modify/write.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When netconsole is enabled, logging messages generated during tg3_open
can result in a null pointer dereference for the uninitialized tg3
status block. Use the irq_sync flag to disable polling in the early
stages. irq_sync is cleared when the driver is enabling interrupts after
all initialization is completed.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: NKosta Zertsekel <konszert@marvell.com>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a missing break statement so FLASH_5762_EEPROM_HD gets treated
like FLASH_5762_EEPROM_LD.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit de0a4148 added Kconfig logic to
select HWMON and removed all the IS_ENABLED(CONFIG_HWMON) checks in the
tg3.c file. It missed this one check in the header.

Update version to 3.129 and update copyright year.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the code to detect PCI function number on 5717, 5719, and 5720.
If shared memory does not have proper signature, read the function number
from register directly.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Detect NVRAM types for 5762 and read OTP firmware version.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add basic support for 5762 which is a 57765_PLUS class device.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers.  This patch fixes all of
them back up to be properly aligned.

Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the hardware timestamping as described in
Documentation/networking/timestamping.txt

Update version to 3.128.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the SIOCSHWTSTAMP ioctl as described in
Documentation/networking/timestamping.txt

[Removed HWTSTAMP_FILTER_ALL handling by returning -ERANGE based on input
 from Richard Cochran.]
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the ptp_caps structure, ptp api implementation,
reference clock read and register/unregister functions.  All the basic
clock operations as described in Documentation/ptp/ptp.txt are
supported.

Frequency adjustment is performed using hardware with a 24 bit
accumulator and a programmable correction value. On each clk, the
correction value gets added to the accumulator and when it overflows,
the time counter is incremented/decremented and the accumulator reset.

So conversion from ppb to correction value is
	ppb * (1 << 24) / 1000000000

[Re-organized to put the ptp_clock_info struct declaration in one patch,
 added ptp_clock_info.name, and added locking to tg3_ptp_adjtime() based
 on input from Richard Cochran.]
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds code to write the reference clock. If a chip reset is
performed, the hwclock is reinitialized with the adjusted kernel time
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Every caller holds tp->lock when calling tg3_netif_start() except
tg3_io_resume().  Fix it so that it is all consistent.  The subsequent
PTP patches add tg3_ptp_resume() to tg3_netif_start() and the tp->lock
is required.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

irq_cnt is no longer reliable since rxq_cnt can be independently configured.

Update version to 3.127.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The watchdog will not trigger when the carrier is off when reconfiguring
the device.  Because carrier state is now off during reset, we need to
introduce a link_up flag to keep track of link state during PHY setup.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Also refactor the conditional to use the existing tg3_pci_tbl array.
- Set flags in the driver_data field of the pci_device_id structure to
identify these devices.
- Add PCI_DEVICE_SUB() to pci.h to declare PCI 4-part IDs to match these
devices.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

instead of making separate tg3_napi_disable() and netif_tx_disable() calls.

Update version to 3.126.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for 5717C0 which is a 5720A0 with special bonds-out option.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/broadcom/tg3.c:8121:8: warning: symbol 'i' shadows an earlier one
drivers/net/ethernet/broadcom/tg3.c:8003:6: originally declared here
drivers/net/ethernet/broadcom/tg3.c:785:5: warning: symbol 'tg3_ape_scratchpad_read' was not declared. Should it be static?
drivers/net/ethernet/broadcom/tg3.c:7781:19: warning: Using plain integer as NULL pointer
drivers/net/ethernet/broadcom/tg3.c:10231:31: error: bad constant expression
Reported-by: NFengguang Wu <fenguang.wu@intel.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is the seldom used corner case where HWMON=m at the same
time as TIGON3=y (typically randconfigs) which will cause a link
fail like:

drivers/built-in.o: In function `tg3_close':
tg3.c:(.text+0x16bd86): undefined reference to `hwmon_device_unregister'
drivers/built-in.o: In function `tg3_hwmon_open':
tg3.c:(.text+0x16fc4b): undefined reference to `hwmon_device_register'
make[1]: *** [vmlinux] Error 1

Fix it as suggested by DaveM[1] by having the Kconfig logic simply
select HWMON when TIGON3 is selected.  This gets rid of all the
extra IS_ENABLED ifdeffery in tg3.c as a side benefit.

[1] http://marc.info/?l=linux-netdev&m=134250573718151&w=2

Cc: Michael Chan <mchan@broadcom.com>
Reported-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: NAnisse Astier <anisse@astier.eu>
Suggested-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simple round-robin hardware TX scheduling can cause starvation of TX rings
with small packets when other TX rings have large TSO or jumbo packets.

In the simplest case, consider 2 TCP streams running in opposite
directions.  The TSO TX traffic will hash to one ring and the ACKs for the
incoming data on a different TCP connection will hash to a different TX
ring.  The hardware fetches one complete TSO packet (up to 64K data)
before servicing the other TX ring.  When it gets to the other TX ring, it
will only fetch one packet (64-byte ACK packet in this case).  After that,
it will switch back to the 1st ring filled with more TSO packets.  Because
only one ACK can go out roughly every 500 usec in this case, the incoming
data rate becomes very low.

Update version to 3.125.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Default remains the same.
Reviewed-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

by introducing tg3_stop() that does the opposite of tg3_start().  This
function will be useful when adding the support for changing the numbe
of rx and tx rings.
Reviewed-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

by introducing tg3_start() that handles all initialization steps from
IRQ allocation.  This function will be needed when adding support for
changing the number of rx and tx rings.
Reviewed-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

since the number of rings can be different.
Reviewed-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

irq_cnt is no longer necessarily equal to the number rx or tx rings.
Reviewed-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is preparation work to allow the number of RX and TX rings to be
configured separately.
Reviewed-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Use PCI Express Capability access functions to simplify tg3 driver.

[bhelgaas: split bnx2x and tg3 into separate patches]
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Spinlock should be taken before checking for tp->hw_stats.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>