Add device capability, firmware command opcode and etc prior elements
needed for QCN suppprt. Disable SRIOV VF view/access for QCN is disabled.

While here, remove a redundant offset definition into the
QUERY_DEV_CAP mailbox.
Signed-off-by: NShani Michaeli <shanim@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the hardware interface required for port aggregation.

1. Disable RX port check on receive - don't perform a validity check
that matches to QP's port and the port where the packet is received.

2. Virtual to physical port remap - configure virtual to physical port
mapping. Port remap capability for virtual functions.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a memory corruption at mlx4_MAD_IFC_wrapper.

A table of size dev->caps.pkey_table_len[port]*sizeof(*table)
was allocated, but get_full_pkey_table() assumes that the number
of entries in the table is a multiplication of 32 (which isn't always
correct).

Fixes: 0a9a0188 ('mlx4: MAD_IFC paravirtualization')
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver incorrectly assigned an out-mailbox to this command,
and used an opcode modifier = 0, which is a reserved value (it
should use opcode modifier = 1).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When SRIOV commands are executed over the comm-channel and get
a fatal error (e.g. timeout, closing command failure) the VF enters
into error state and reset flow is activated.

To be able to recognize whether the failure was on a closing command, the
operational code for the given VHCR command is used. Once the device entered
into an error state we prevent redundant error messages from being printed.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In SRIOV, both the PF and the VF may attempt device recovery whenever they
assume that the device is not functioning.  When the PF driver resets the
device, the VF should detect this and attempt to reinitialize itself.

The VF must be able to reset itself under all circumstances, even
if the PF is not responsive.

The VF shall reset itself in the following cases:

1. Commands are not processed within reasonable time over the communication channel.
This is done considering device state and the correct return code based on
the command as was done in the native mode, done in the next patch.

2. The VF driver receives an internal error event reported by the PF on the
communication channel. This occurs when the PF driver resets the device or
when VF is out of sync with the PF.

Add 'VF reset' capability, which allows the VF to reinitialize itself even when the
PF is not responsive.

As PF and VF may run their reset flow simulantanisly, there are several cases
that are handled:
- Prevent freeing VF resources upon FLR, when PF is in its unloading stage.
- Prevent PF getting VF commands before it has finished initializing its resources.
- Upon VF startup, check that comm-channel is online before sending
  commands to the PF and getting timed-out.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We activate reset flow upon command fatal errors, when the device enters an
erroneous state, and must be reset.

The cases below are assumed to be fatal: FW command timed-out, an error from FW
on closing commands, pci is offline when posting/pending a command.

In those cases we place the device into an error state: chip is reset, pending
commands are awakened and completed immediately. Subsequent commands will
return immediately.

The return code in the above cases will depend on the command. Commands which
free and close resources will return success (because the chip was reset, so
callers may safely free their kernel resources). Other commands will return -EIO.

Since the device's state was marked as error, the catas poller will
detect this and restart the device's software stack (as is done when a FW
internal error is directly detected). The device state is protected by a
persistent mutex lives on its mlx4_dev, as such no need any more for the
hcr_mutex which is removed.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Maintain a persistent memory that should survive reset flow/PCI error.
This comes as a preparation for coming series to support above flows.
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactoring mlx4_cmd_init and mlx4_cmd_cleanup such that partial init
and cleanup are possible. After this refactoring, calling mlx4_cmd_init
several times is safe.

This is necessary in the VF init flow when mlx4_init_hca returns -EACCESS,
we need to issue cleanup and re-attempt to call it with the slave flag.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add code to issue CONFIG_DEV "get" firmware command.

This command is used in order to obtain certain parameters used for
supporting various RX checksumming options and vxlan UDP port.

The GET operation is allowed for VFs too.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NShani Michaeli <shanim@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added wrapper to the ACCESS_REG command for handling guest HW
registers access, preventing write operations, but do allow reads.

This will prevent SRIOV guests to change port PTYS configuration,
such as speed/advertised link modes.

Fixes: adbc7ac5 ('net/mlx4_core: Introduce ACCESS_REG CMD [...]')
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding ACCESS REG mlx4 command and use it to implement Query method for
PTYS (Port Type and Speed Register).
Query and store eth_prot_ctrl dev cap.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ConnectX2 HCAs have max_mtu=4k and max_vl=8 vls. However, if you specify
a 4K mtu, the max_vl supported for 4K is 4 vls. The driver at startup
attempts to set a 4K mtu using the max_vl value obtained from QUERY_PORT.

Since the max_vl value is 8 vls (which is supported up to 2K mtu size),
the first attempt to set the mtl/vl port value will fail, generating
the following error message in the log:

  mlx4_core 0000:06:00.0: command 0xc failed: fw status = 0x40

The driver then tries again, using mtu=4k, vls=4, and this succeeds.

Since we do not want to have this error message always displayed at driver
start when there are ConnectX2 HCAs on the host, we deprecate the error
message for this specific command/input_modifier/opcode_modifier/fw-status
to be debug.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Single port VFs are seen PCI wise on both ports of the PF (we don't have
single port PFs with ConnectX). With this in mind, it's possible for
virtualization tools to try and configure a single ported VF through
the "wrong" PF port.

To handle that, we use the PF driver mapping of single port VFs to NIC
ports and adjust the port value before calling into the low level
code that does the actual VF configuration

Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fix spelling typo in printk.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Secure-host is the general term for the capability of a device
to protect itself and the subnet from malicious host software.

This is achieved by:
1. Not allowing un-trusted entities to access device configuration
   registers, directly (through pci_cr or pci_conf) and indirectly
   (through MADs).

2. Hiding M_Key from untrusted entities.

3. Preventing the modification of GUID0 by un-trusted entities

4. Not allowing drivers on untrusted hosts to receive nor to transmit
   packets over QP0 (SMP Firewall).

The secure-host capability depends on firmware handling all QP0
packets, and not passing these packets up to the driver. Any information
required by the driver for proper operation (e.g., SM lid) is passed
via events generated by the firmware while processing QP0 MADs.

Driver support mainly requires using the MAD_DEMUX FW command at startup,
where the feature is enabled/disabled through a procedure described in
the Mellanox HCA tools package.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>

[ Fix error path in mlx4_setup_hca to go to err_mcg_table_free. - Roland ]
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This commit adds the sysfs interface for enabling QP0 on VFs for
selected VF/port.

By default, no VFs are enabled for QP0 operation.

To enable QP0 operation on a VF/port, under
/sys/class/infiniband/mlx4_x/iov/<b:d:f>/ports/x there are two new entries:

- smi_enabled (read-only). Indicates whether smi is currently
  enabled for the indicated VF/port

- enable_smi_admin (rw). Used by the admin to request that smi
  capability be enabled or disabled for the indicated VF/port.
  0 = disable, 1 = enable.
  The requested enablement will occur at the next reset of the
  VF (e.g. driver restart on the VM which owns the VF).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This commit adds the infrastructure for enabling selected VFs to
operate SMI (QP0) MADs without restriction.

Additionally, for these enabled VFs, their QP0 proxy and tunnel QPs
are MLX QPs.  As such, they operate over VL15.  Therefore, they are
not affected by "credit" problems or changes in the VLArb table (which
may shut down VL0).

Non-enabled VFs may only create UD proxy QP0 qps (which are forced by
the hypervisor to send packets using the q-key it assigns and places
in the qp-context).  Thus, non-enabled VFs will not pose a security
risk.  The hypervisor discards any privileged MADs it receives from
these non-enabled VFs.

By default, all VFs are NOT enabled, and must explicitly be enabled
by the administrator.

The sysfs interface which operates the VF enablement infrastructure
is provided in the next commit.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Currently, VFs in SRIOV VFs are denied QP0 access.  The main reason
for this decision is security, since Subnet Management Datagrams
(SMPs) are not restricted by network partitioning and may affect the
physical network topology.  Moreover, even the SM may be denied access
from portions of the network by setting management keys unknown to the
SM.

However, it is desirable to grant SMI access to certain privileged
VFs, so that certain network management activities may be conducted
within virtual machines instead of the hypervisor.

This commit does the following:

1. Create QP0 tunnel QPs for all VFs.

2. Discard SMI mads sent-from/received-for non-privileged VFs in the
   hypervisor MAD multiplex/demultiplex logic.  SMI mads from/for
   privileged VFs are allowed to pass.

3. MAD_IFC wrapper changes/fixes.  For non-privileged VFs, only
   host-view MAD_IFC commands are allowed, and only for SMI LID-Routed
   GET mads.  For privileged VFs, there are no restrictions.

This commit does not allow privileged VFs as yet.  To determine if a VF
is privileged, it calls function mlx4_vf_smi_enabled().  This function
returns 0 unconditionally for now.

The next two commits allow defining and activating privileged VFs.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
  to have a bandwidth of at least this value.
  max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
  of up to this value.

o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
  which takes 4 arguments:
  netdev, VF number, min_tx_rate, max_tx_rate

o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.

o Drivers that currently implement ndo_set_vf_tx_rate should now call
  ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
  greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
  implemented by driver.

o If user enters only one of either min_tx_rate or max_tx_rate, then,
  userland should read back the other value from driver and set both
  for IFLA_VF_RATE.
  Drivers that have not yet implemented IFLA_VF_RATE should always
  return min_tx_rate as 0 when read from ip tool.

o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
  IFLA_VF_RATE should override.

o Idea is to have consistent display of rate values to user.

o Usage example: -

  ./ip link set p4p1 vf 0 rate 900

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 600 rate 300

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As checkpatch suggests. Also changed some printk's into pr_*
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds UPDATE_QP SRIOV wrapper support.

The mechanism is a general one, but currently only source MAC
index changes are allowed for VFs.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the "error: we previously assumed 'out_param' could be null" found
by smatch semantic checker on:
drivers/net/ethernet/mellanox/mlx4/cmd.c:506 mlx4_cmd_poll()
drivers/net/ethernet/mellanox/mlx4/cmd.c:578 mlx4_cmd_wait()
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more current logging style.

o Coalesce formats
o Add missing spaces for coalesced formats
o Align arguments for modified formats
o Add missing newlines for some logging messages
o Use DRV_NAME as part of format instead of %s, DRV_NAME to
  reduce overall text.
o Use ..., ##__VA_ARGS__ instead of args... in macros
o Correct a few format typos
o Use a single line message where appropriate
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-By: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce the CONFIG_DEV firmware command which we will use to
configure the UDP port assumed by the firmware for the VXLAN offloads.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a VF issues a firmware command which is disallowed for them, the PF
rerturns -EPERM from that command wrapper. Move to use one such wrapper
instance, instead of repeating the same code on such commands.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
	In wrapped commands, we need to verify and convert
	the slave's port into the real physical port.
	Furthermore, when sending the response back to the slave,
	a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
	The slave assumes that sqpn is used for QP1 communication.
	If the slave is assigned to a port != (first port), we need
	to adjust the sqpn that will direct its QP1 packets into the
	correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
	In B0 steering, gid[5] contains the port. It needs
	to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
	When a slave queries the hardware, it needs to view only
	the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
	The QP port is encoded in the sched_qp, thus in modify_qp we need
	to encode the correct port in sched_qp.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the following utils:
1. Convert slave_id -> VF
2. Get the active ports by slave_id
3. Convert slave's port to real port
4. Get the slave's port from real port
5. Get all slaves that uses the i'th real port
6. Get all slaves that uses the i'th real port exclusively
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,

This is achieved as follows:
Outgoing MADs:
    1. Source MAC: obtained from the CQ completion structure
       (struct ib_wc, smac field).
    2. Destination MAC: obtained from the tunnel header
    3. vlan_id: obtained from the tunnel header.
Incoming MADs
    1. The source (i.e., remote) MAC and vlan_id are passed in
       the tunnel header to the proxy QP1.

VST mode support:
     For outgoing MADs,  the vlan_id obtained from the header is
        discarded, and the vlan_id specified by the Hypervisor is used
        instead.
     For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
        "invalid" vlan (0xffff)  is substituted when forwarding to the slave.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for allocating IB UD QPs that we can steer
traffic from.  We introduce a new firmware command FLOW_STEERING_IB_UC_QP_RANGE
and a capability bit.

This command isn't supported for VFs.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Allow immediate activate of VGT->VST and VST->VGT transitions, without
the need of rebinding in mlx4_master_immediate_activate_vlan_qos().

Also in struct res_qp: add qp parameters (vlan_index,fvl,vlan_cntrol..)
to the saved set, in order to restore when move to VGT.
 - Clear at mlx4_RST2INIT_QP_wrapper()
 - Save at mlx4_INIT2RTR_QP_wrapper()
 - Restore at mlx4_vf_immed_vlan_work_handler()

Update mlx4_vf_immed_vlan_work_handler() to support VGT.
Signed-off-by: NRony Efraim <ronye@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To guarantee that all unused fields in all FW commands for both inboxes
and outboxes are zeroed out, initialize the mailbox buffer to all zeroes.

This is especially important for SRIOV comm-channel virtual commands
(such as QUERY_FUNC_CAP), where if new fields are added to support new
features, the driver can depend on older kernels passing zeroes in these
fields.

In addition to zeroing out the mailbox buffer at allocation time, all
(now unnecessary) calls to memset by the callers of
mlx4_alloc_cmd_mailbox() are removed.
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In upstream kernels under SRIOV, the vlan register/unregister calls
were NOPs (doing nothing and returning OK). We detect these old
calls from guests (via the comm channel), since previously the
port number in mlx4_register_vlan was passed (improperly) in the
out_param. This has been corrected so that the port number is now
passed in bits 8..15 of the in_modifier field.

For old calls, these bits will be zero, so if the passed port
number is zero, we can still look at the out_param field to see
if it contains a valid port number. If yes, the VM is running
an old driver.

Since for old drivers, the register/unregister_vlan wrappers were
NOPs, we continue this policy -- the reason being that upstream
had an additional bug in eth driver running on guests (where
procedure mlx4_en_vlan_rx_kill_vid() had the following code:

if (!mlx4_find_cached_vlan(mdev->dev, priv->port, vid, &idx))
        mlx4_unregister_vlan(mdev->dev, priv->port, idx);
else
        en_err(priv, "could not find vid %d in cache\n", vid);

On a VM, mlx4_find_cached_vlan() will always fail, since the
vlan cache is located on the Hypervisor; on guests it is empty.

Therefore, if we allow upstream guests to register vlans, we will
have vlan leakage since the unregister will never be performed.
Leaving vlan reg/unreg for old guest drivers as a NOP is not a
feature regression, since in upstream the register/unregister
vlan wrapper is a NOP.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use of vlan_index created problems unregistering vlans on guests.

In addition, tools delete vlan by tag, not by index, lets follow that.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function mlx4_master_deactivate_admin_state() __mlx4_unregister_mac was
called using the MAC index. It should be called with the value of the MAC itself.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove code that triggers trivial build warnings.

drivers/net/ethernet/mellanox/mlx4/cmd.c: In function ‘mlx4_set_vf_vlan’:
drivers/net/ethernet/mellanox/mlx4/cmd.c:2256: warning: variable ‘vf_oper’ set but not used
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_map_sw_to_hw_steering_mode’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:648: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_map_sw_to_hw_steering_id’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:685: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_hw_rule_sz’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:712: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/fw.c: In function ‘mlx4_opreq_action’:
drivers/net/ethernet/mellanox/mlx4/fw.c:1732: warning: variable ‘type_m’ set but not used
drivers/net/ethernet/mellanox/mlx4/srq.c:302: warning: no previous prototype for ‘mlx4_srq_lookup’
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These local functions are used only in this file.
Fix the following sparse warnings:

drivers/net/ethernet/mellanox/mlx4/cmd.c:803:5: warning: symbol 'MLX4_CMD_UPDATE_QP_wrapper' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx4/cmd.c:812:5: warning: symbol 'MLX4_CMD_GET_OP_REQ_wrapper' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx4/cmd.c:1547:5: warning: symbol 'mlx4_master_immediate_activate_vlan_qos' was not declared. Should
it be static?
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-By: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds new firmware command and new firmware event.  The firmware
raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it
needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ
command. At the moment the supported operation is adding/removing multicast
entries which are used by the firmware for handling NCSI traffic in B0
steering mode.

Also, had to swap the order of mlx4_init_mcg_table() and
mlx4_init_eq_table() to make sure that driver will get events only after
resources are initialized to handle it.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"work" needs to be freed before returning on this error path.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the firmware supports the UPDATE_QP command, if the VF link is disabled,
block all QPs opened by the VF, by programming the UPDATE_QP command to drop
all RX & TX traffic to/from these QPs. Operates only in VST mode.
Signed-off-by: NRony Efraim <ronye@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>