Add a slave_configure function to iSCSI TCP to remove any DMA
alignment restriction.  This permits the use of direct IO from
arbitrary addresses.
Signed-off-by: NPete Wyckoff <pw@osc.edu>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

If we got the padding, data and header in different skbs,
we were not handling the padding correctly because we attributed it
to the data's skb. This resulted in the initiator reading from
pad bytes + skb offset instead of the correct offset.

If you could not connect with the open solaris target, this
will fix the lock up problem you were hitting.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch allows us to set can_queue and cmds_per_lun from userspace
when we create the session/host. From there we can set it on a per
target basis. The patch fully converts iscsi_tcp, but only hooks
up ib_iser for cmd_per_lun since it currently has a lots of preallocations
based on can_queue.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The cmdsn allocation and pdu transmit code can race, and we can end
up sending a pdu with cmdsn 10 before a pdu with 5. The target will
then fail the connection/session. This patch fixes the problem by
delaying the cmdsn allocation until we are about to send the pdu.

This also removes the xmitmutex. We were using the connection xmitmutex
during error handling to handle races with mtask and ctask cleanup and
completion. For ctasks we now have nice refcounting and for the mtask,
if we hit the case where the mtask timesout and it is floating
around somewhere in the driver, we end up dropping the session.
And to handle session level cleanup, we use the xmit suspend bit
along with scsi_flush_queue and the session lock to make sure
that the xmit thread is not possibly transmitting a task while
we are trying to kill it.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

If iscsi_tcp partially sends a header, it would recalculate the
header size and readd the size of the digest (if header digests
are used).This would cause us to send sizeof(digest) extra bytes
when we sent the rest of the header.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The attached patches add sysfs files for the chap settings
to the iscsi transport class, iscsi_tcp and ib_iser. This is
needed for software iscsi because there are times when iscsid
can die and it will need to reread the values it was using.
And it is needed by qla4xxx for basic management opertaions.
This patch does not hook in qla4xxx yet, because I am not sure
the mbx command to use.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- Remove shadow of request length from struct iscsi_cmd_task.
- change all users to use scsi_cmnd->request_bufflen directly

(With bidi we will use scsi-ml API to retrieve in/out length)
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NBenny Halevy <bhalevy@panasas.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch fixes handling of expected datasn/r2tsn as received from
target. It is done according to: T10 rfc3720 section 3.2.2.3. Data Sequencing.

. unify expected datasn/r2tsn into one counter
. calculate than check expected datasn/r2tsn. On error print a message
  and fail the request. (TODO use iscsi retransmits)
. remove the FIXME   ;)
. avoid zero length memset
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NBenny Halevy <bhalevy@panasas.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

For iscsi root boot, software iscsi needs to know what the BIOS/OF
initiator used for the initiator name so this puts it in sysfs
for userspace to be able to pick up.

For hw iscsi, it is nice to see what the card is using.

This patch adds the new param, and hooks in qla4xxx, iscsi_tcp, and ib_iser.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

iscsid and udev need to key off the hw address being
used so add some helpers for iser and iscsi tcp.

Also convert them
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The iscsi class uses the set_param event to set session
and connection params. This patch adds a set_host_param
so we can set host level values.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

We are going to be adding more host level sysfs attrs and
set_params, so this patch has them take a scsi_host instead
of either a scsi_host or host no.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Export mac as hw address.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Add hw address sysfs file.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Let's not oops when we cannot allocate a skb! Add a check
for if alloc_skb fails.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Inspired by Brian King's patch to the ibmvscsi driver. Adds support for
a changeable queue depth to the aacraid driver.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NSumant Patro <sumant.patro@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NSumant Patro <sumant.patro@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.

Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NSumant Patro <sumant.patro@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Currently accessing the scsi host private data is rather messy because
it comes as an unsigned long that always needs a cast first.  This patch
introduces a helper that does the cast called shost_priv.  It's similar
in spirit to netdev_priv for network drivers.

This is the first patch introducing the macro, and the second patch
in the series will convert esp and it's subdrivers as an example.
Further conversion will wait until the helper is in the tree to make
patch juggling easier.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.

Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>

ACK. Code inspected. Driver changes NOT unit tested or compile tested.
Acked-by: N"Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This removes the remaining unnecessary map_single path
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Conflicts:

	drivers/scsi/jazz_esp.c

Same changes made by both SCSI and SPARC trees: problem with UTF-8
conversion in the copyright.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.

Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NAdam Radford <linuxraid@amcc.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.

Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NAdam Radford <linuxraid@amcc.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

It should be pass "newsize" to vmtruncate function to modify the
inode->i_size, while the old size is passed to vmtruncate.

This bug was caught by LTP truncate test case on Blackfin platform.
After it was fixed, the LTP truncate test case passed.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The current code is leaking a reference to dreq->kref when the calls to
nfs_direct_read_schedule() and nfs_direct_write_schedule() return an
error.
This patch moves the call to kref_put() from nfs_direct_wait() back into
nfs_direct_read() and nfs_direct_write() (which are the functions that
actually took the reference in the first place) fixing the leak.

Thanks to Denis V. Lunev for spotting the bug and proposing the original
fix.
Acked-by: NDenis V. Lunev <dlunev@gmail.com>
Acked-by: NChuck Lever <chuck.lever@oracle.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

ugh, this function gets called by our unwinder. recursive backtrace for
the win... bisection to find this one was "fun."
Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some of the new syscalls require supporting TIF_RESTORE_SIGMASK.
Signed-off-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove 2 functions private to the alpha implemetation,
in favor of similar functions in <linux/log2.h>.

Provide a more efficient version of the fls64 function
for pre-ev67 alphas.
Signed-off-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] Fix some section mismatch warnings
  [ARM] 4417/1: Serial: Fix AMBA drivers locking
  [ARM] 4394/1: ARMv7: Add the TLB range operations
  [ARM] 4410/1: Remove extern declarations in coyote/ixdpg425-pci.c
  [ARM] 4416/1: NWFPE: fix undeclared symbols
  [ARM] 4415/1: AML5900: fix sparse warnings from map_io
  [ARM] 4414/1: S3C2443: sparse fix for clock.c
  [ARM] 4412/1: S3C2412: reset errata fix
  [ARM] 4411/1: KS8695: Another serial driver fix
  [ARM] oprofile: avoid lockdep warnings on mpcore oprofile init
  [ARM] Fix stacktrace FP range checking
  [ARM] use __used attribute
  [ARM] enable arbitary speed tty ioctls and split input/output speed
  [ARM] remove unused header file: arch/arm/mach-s3c2410/bast.h
  [ARM] 4406/1: Trivial NSLU2 / NAS-100D header & setup code cleanup
  [ARM] 4405/1: NSLU2, DSM-G600 frequency fixup code
  [ARM] 4404/1: Trivial IXP42x Kconfig cleanup
  [ARM] 4403/1: Make the PXA-I2C driver work with lockdep validator
  [ARM] 4402/1: S3C2443: Add physical address of HSMMC controller
  [ARM] 4401/1: S3C2443: Add definitions for port GPIOJ

The following patch fixes these section mismatch warnings:

WARNING: arch/arm/mach-at91/built-in.o(.text+0xdf4): Section mismatch: reference to .init.data:dk_nand_partition (between 'nand_partitions' and 'at91_leds_event')
WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (after 'nand_partitions')
WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (between 'nand_partitions' and 'ads7843_pendown_state')
WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (after 'nand_partitions')
WARNING: arch/arm/mach-at91/built-in.o(.text+0xc28): Section mismatch: reference to .init.data:kb9202_nand_partition (after 'nand_partitions')
WARNING: arch/arm/mach-footbridge/built-in.o(.text+0xaa4): Section mismatch: reference to .init.data:cats_pci (between 'cats_pci_init' and 'ebsa285_leds_event')WARNING: arch/arm/mach-ixp2000/built-in.o(.text+0xb54): Section mismatch: reference to .init.text:ixp2000_init_irq (between 'ixdp2x00_init_irq' and 'ixdp2x00_irq_handler')
WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x670): Section mismatch: reference to .init.text:ixp23xx_pci_common_init (between 'ixp23xx_pci_slave_init' and 'ixp23xx_pci_scan_bus')
WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x890): Section mismatch: reference to .init.text:ixp23xx_init_irq (between 'ixdp2351_init_irq' and 'roadrunner_pci_preinit')
WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x9a8): Section mismatch: reference to .init.text:ixp23xx_pci_preinit (after 'roadrunner_pci_preinit')
WARNING: arch/arm/mach-imx/built-in.o(__ksymtab+0x80): Section mismatch: reference to .init.text:imx_set_mmc_info (between '__ksymtab_imx_set_mmc_info' and '__ksymtab_set_imx_fb_info')
WARNING: arch/arm/mach-imx/built-in.o(__ksymtab+0x88): Section mismatch: reference to .init.text:set_imx_fb_info (after '__ksymtab_set_imx_fb_info')
WARNING: arch/arm/mach-sa1100/built-in.o(.text+0x1930): Section mismatch: reference to .init.data:neponset_port_fns (between 'neponset_probe' and 'assabet_leds_event')
WARNING: drivers/built-in.o(.text+0x3f100): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted')
WARNING: drivers/built-in.o(.text+0x3f1c8): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted')
WARNING: drivers/built-in.o(.text+0x4f988): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted')
WARNING: drivers/built-in.o(.text+0x4fa50): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted')
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Acked-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  ehea: Fixed multi queue RX bug
  sky2: enable IRQ on duplex renegotiation
  e1000: restore netif_poll_enable call but make sure IRQs are off
  defxx: Fix the handling of ioremap() failures
  sky2: program proper register for fiber PHY
  sky2: checksum offload plus vlan bug
  sky2: dont set bogus bit in PHY register
  [PATCH] hostap: Allocate enough tailroom for TKIP
  [PATCH] softmac: alloc_ieee80211() NULL check
  [PATCH] ieee80211: fix incomplete error message
  [PATCH] prism54: fix monitor mode oops

* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
  [XFS] Write at EOF may not update filesize correctly.

Must access the respective queue's dummy netdev instead of the port's netdev.
Signed-off-by: NThomas Klein <tklein@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Don't want IRQ on FIFO error because there is nothing useful to do with it.
But do want IRQ on duplex change.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This restores the previously removed netif_poll_enable call in e1000_open.
It's needed on all but the first call to e1000_open for a NIC as
e1000_close always calls netif_poll_disable.

netif_poll_enable can only be called safely if no polls have been
scheduled.  This should be the case as long as we don't enter our IRQ
handler.

In order to guarantee this we explicitly disable IRQs as early as possible
when we're probing the NIC.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Cc: "Kok, Auke" <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

 If ioremap_nocache() is unfortunate enough to fail, the error code is not
set correctly leading to a false success from dfx_register().  This change
fixes the problem.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>