A left-over from prior to component framework.  The original intent was
to deal with hdmi getting unloaded before the master component, but that
isn't really going to work anyways.  These days with the component
framework taking care to unload the master component first, we don't
have to worry about this.
Signed-off-by: NRob Clark <robdclark@gmail.com>

The core clock rate depends on the hw configuration. Once we have
read the hardware revision, we can set the core clock to its
maximum value.
Before then, the clock is set at a rate supported by all MDP5
revisions.
Signed-off-by: NStephane Viau <sviau@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

For mdp5, the irqs of hdmi/eDP/dsi0/dsi1 blocks get routed through the
mdp block.  In order to decouple hdmi/eDP/etc, register an irq domain
in mdp5.  When hdmi/dsi/etc are used with mdp4, they can directly setup
their irqs in their DT nodes as normal.  When used with mdp5, instead
set the mdp device as the interrupt-parent, as in:

	mdp: qcom,mdss_mdp@fd900000 {
		compatible = "qcom,mdss_mdp";
		interrupt-controller;
		#interrupt-cells = <1>;
		...
	};

	hdmi: qcom,hdmi_tx@fd922100 {
		compatible = "qcom,hdmi-tx-8074";
		interrupt-parent = <&mdp>;
		interrupts = <8 0>;   /* MDP5_HW_INTR_STATUS.INTR_HDMI */
		...
	};

There is a slight awkwardness, in that we cannot disable child irqs
at the mdp level, they can only be cleared in the child block.  So
you must not use threaded irq handlers in the child.  I'm not sure
if there is a better way to deal with that.
Signed-off-by: NRob Clark <robdclark@gmail.com>

- More CI dpm fixes
- Initial DPM fan control for SI/CI (disabled by default)
- GPUVM multi-ring efficiency improvements
- Some cursor fixes

* 'drm-next-3.19' of git://people.freedesktop.org/~agd5f/linux: (22 commits)
  drm/radeon: update the VM after setting BO address v4
  drm/radeon: sync PT updates as shared v2
  drm/radeon: sync PD updates as shared
  drm/radeon: fence BO_VAs manually
  drm/radeon: use one VMID for each ring
  drm/radeon: track VM update fences separately
  drm/radeon: fence PT updates manually v2
  drm/radeon: split semaphore and sync object handling v2
  drm/radeon: remove unnecessary VM syncs
  drm/radeon: stop re-reserving the BO in radeon_vm_bo_set_addr
  drm/radeon: rework vm_flush parameters
  drm/radeon/ci: disable needless sclk changes
  drm/radeon/ci: force pcie level before sclk and mclk
  drm/radeon/ci: use different smc command for pcie dpm
  drm/radeon/ci: apply disp voltage changes before clk changes
  drm/radeon: fix PCC debugging message for CI DPM
  drm/radeon/dpm: add thermal dpm support for CI
  drm/radeon/dpm: add smc fan control for CI (v2)
  drm/radeon/dpm: add smc fan control for SI (v2)
  drm/radeon: work around a hw bug in MGCG on CIK
  ...

The vfree() function performes also input parameter validation. Thus the test
around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Reviewed-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The vunmap() function performes also input parameter validation. Thus the test
around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Reviewed-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The drm_fbdev_cma_hotplug_event() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Reviewed-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Reviewed-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is an oversight from

commit f52b69f1
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Wed Nov 19 18:38:08 2014 +0100

    drm/atomic: Don't overrun the connector array when hotplugging

Cc: Dave Airlie <airlied@redhat.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It happens on occasion that developers of generic user-space applications
abuse the dumb buffer API to get hold of drm buffers that they can both
mmap() and use for GPU acceleration, using the assumptions that dumb buffers
and buffers available for GPU are
a) The same type and can be aribtrarily type-casted.
b) fully coherent.

This patch makes the most widely used drivers warn nicely when that happens,
the next step will be to fail.

v2: Move drmP.h changes to drm_gem.h. Fix Radeon dumb mmap breakage.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This way the necessary VM update is kicked off immediately
if all BOs involved are in GPU accessible memory.

v2: fix vm lock
v3: immediately update unmaps as well
v4: use drm_free_large instead of kfree
Tested-by: NKai Wasserbäch <kai@dev.carbon-project.org>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Only invalidating PTEs needs to be executed synchronized to using the PT.

v2: fix sync to uses
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We never invalidate PD entries and making them valid can
run with other users in parallel.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This allows us to finally remove the VM fence and
so allow concurrent use of it from different engines.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use multiple VMIDs for each VM, one for each ring. That allows
us to execute flushes separately on each ring, still not ideal
cause in a lot of cases rings can share IDs.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Note for each fence if it's a VM page table update or not. This allows
us to determine the last VM update in a sync object and so to figure
out if we need to flush the TLB or not.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This allows us to add the real execution fence as shared.

v2: fix typo
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Previously we just allocated space for four hardware semaphores
in each software semaphore object. Make software semaphore objects
represent only one hardware semaphore address again by splitting
the sync code into it's own object.

v2: fix typo in comment
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The PD/PTs reservation object now contains everything needed.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

That's useless when all callers drop the reservation
immediately after calling the function.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use ring structure instead of index and provide vm_id and pd_addr separately.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The current code always reprogrammed the sclk levels,
but we don't currently handle disp sclk requirements
so just skip it.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Preferred ordering.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use unforce levels rather than enable mask instruction.
This is the preferred method.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Apply voltage changes for displays before changing clocks.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add missing newline and print the bad gpio shift.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Not currently used.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Enable smc fan control for CI boards.  Should
reduce the fan noise on systems with a higher
default fan profile.

v2: disable by default, add additional fan setup, rpm control

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=73338Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Enable smc fan control for SI boards.  Should
reduce the fan noise on systems with a higher
default fan profile.

v2: disable by default, add rpm controls

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=73338Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Always need to set bit 0 of RLC_CGTT_MGCG_OVERRIDE
to avoid unreliable doorbell updates in some cases.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

No functional change.
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The cursor_set2 hook provides the cursor hotspot position within the
cursor image. When the hotspot position changes, we can adjust the cursor
position such that the hotspot doesn't move on the screen. This prevents
the cursor from appearing to intermittently jump around on the screen
when the position of the hotspot within the cursor image changes.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Merge AMDKFD it seems clean enough.
* 'amdkfd-v6' of git://people.freedesktop.org/~gabbayo/linux: (29 commits)
  amdkfd: Implement the Get Version IOCTL
  amdkfd: Implement the Get Process Aperture IOCTL
  amdkfd: Implement the Get Clock Counters IOCTL
  amdkfd: Implement the Set Memory Policy IOCTL
  amdkfd: Implement the create/destroy/update queue IOCTLs
  amdkfd: Add interrupt handling module
  amdkfd: Add device queue manager module
  amdkfd: Add process queue manager module
  amdkfd: Add packet manager module
  amdkfd: Add module parameter of scheduling policy
  amdkfd: Add kernel queue module
  amdkfd: Add mqd_manager module
  amdkfd: Add queue module
  amdkfd: Add binding/unbinding calls to amd_iommu driver
  amdkfd: Add basic modules to amdkfd
  amdkfd: Add topology module to amdkfd
  amdkfd: Add amdkfd skeleton driver
  amdkfd: Add IOCTL set definitions of amdkfd
  Update MAINTAINERS and CREDITS files with amdkfd info
  drm/radeon: Add radeon <--> amdkfd interface
  ...

This patch allows framebuffers for cirrus to be created with
32bpp pixel formats provided that they do not violate certain
restrictions of the cirrus hardware.

v2: Use pci resource length for vram size.
Signed-off-by: NZach Reizner <zachr@google.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Only importing an FD to a handle is currently supported on UDL,
but the exporting functionality is equally useful.
Signed-off-by: NHaixia Shi <hshi@chromium.org>
Reviewed-by: NStéphane Marchesin <marcheu@chromium.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

By default set udl_gem_object as cacheable, but set WC flag when attaching
dmabuf. In udl_gem_mmap() update cache attributes based on the flags, similar
to exynos_drm_gem_mmap().
Signed-off-by: NHaixia Shi <hshi@chromium.org>
Reviewed-by: NSonny Rao <sonnyrao@chromium.org>
Reviewed-by: NOlof Johansson <olofj@chromium.org>
Reviewed-by: NStéphane Marchesin <marcheu@chromium.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Before this patch, cirrus_device_init could have failed while
cirrus_mm_init succeeded and the driver would have reported overall
success on load. This patch causes cirrus_device_init to return on
the first error encountered.
Reviewed-by: NStéphane Marchesin <marcheu@chromium.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Oversight from my kerneldoc cleanup when doing the original atomic
helper series - I've only applied this clarification to the modeset
related helpers, and not the plane update code. Remedy this asap.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

I guess for hysterical raisins this was meant to be the way to read
blob properties. But that's done with the two-stage approach which
uses separate blob kms object and the special-purpose get_blob ioctl.

Shipping userspace seems to have never relied on this, and the kernel
also never put any blob thing onto that property. And nowadays it
would blow up, e.g. in drm_property_destroy. Also it makes no sense to
return values in an ioctl that only returns metadata about everything.

So let's ditch all the internal code for the blob list, rename the
list to be unambiguous and sprinkle comments all over the place to
explain this peculiar piece of api.

v2: Squash in fixup from Rob to remove now unused variables.

Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Make it clear that it's a negative errno (more in line with
  everything else).
- Clean up the confusion around get_properties vs. getproperty ioctls:
  One reads per-obj property values, the other reads property
  metadata.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>