The queue_end() macro points to 1 position after the
queue, which means that if we want to know if queue
is at the end of the queue we should first increment
the position and then check if it is a valid entry.

This fixes a segmentation fault which only occurs when
the device has enough endpoints to provide a dedicated
endpoint for all TX queues (which likely won't happen
for rt2500usb and rt73usb, but will happen for rt2800usb).
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All LM87 firmwares need a explicit termination "packet",
in oder to finish the pending transfer properly.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes two small flaws:
 - restore the original TKIP IV if we altered it.
 - reserve & initialize ICV with zeros.
   This is actually only necessary for some obsolete p54usb firmwares.
   But we don't know yet, if all devices are compatible with the new revisions.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported by Michael Jarosch <mitsch@riotmusic.de>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

0x1b is a 3945 specific command, we should print it too when debugging.
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The chainmasks have to be updated before setting the channel,
since the HW reset routine uses them to set the appropriate registers.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the warning reproduced below.

We add to rx_list in interrupt context and remove elements in tasklet
context. While removing elements we need to prevent the interrupt
modifying the list.

Note that "orinoco: Process bulk of receive interrupt in a tasklet" did not
preserve locking semantics on what is now orinoco_rx.

This patch reinstates the locking semantics and ensures it covers
rx_list as well. This leads to additional cleanup required in
free_orinocodev.

[89479.105038] WARNING: at lib/list_debug.c:30 __list_add+0x8f/0xa0()
[89479.105058] list_add corruption. prev->next should be next (dddb3568), but was cbc28978. (prev=dddb3568).
[89479.106002] Pid: 15746, comm: X Not tainted 2.6.28-1avb #26
[89479.106020] Call Trace:
[89479.106062]  [<c011d3b0>] warn_slowpath+0x60/0x80
[89479.106104]  [<c01073d0>] ? native_sched_clock+0x20/0x70
[89479.106194]  [<c013d825>] ? lock_release_holdtime+0x35/0x200
[89479.106218]  [<c018d9f0>] ? __slab_alloc+0x550/0x560
[89479.106254]  [<c02f9c9d>] ? _spin_unlock+0x1d/0x20
[89479.106270]  [<c018d9f0>] ? __slab_alloc+0x550/0x560
[89479.106302]  [<c01ff2a7>] ? delay_tsc+0x17/0x24
[89479.106319]  [<c01ff221>] ? __const_udelay+0x21/0x30
[89479.106376]  [<dfa8b1e2>] ? hermes_bap_seek+0x112/0x1e0 [hermes]
[89479.106396]  [<c013d7eb>] ? trace_hardirqs_off+0xb/0x10
[89479.106418]  [<c018e307>] ? __kmalloc_track_caller+0xb7/0x110
[89479.106448]  [<c028eefc>] ? dev_alloc_skb+0x1c/0x30
[89479.106465]  [<c028eefc>] ? dev_alloc_skb+0x1c/0x30
[89479.106482]  [<c020e13f>] __list_add+0x8f/0xa0
[89479.106551]  [<dfd0fcae>] orinoco_interrupt+0xcae/0x16c0 [orinoco]
[89479.106574]  [<c013b0e3>] ? tick_dev_program_event+0x33/0xb0
[89479.106594]  [<c01073d0>] ? native_sched_clock+0x20/0x70
[89479.106613]  [<c013d825>] ? lock_release_holdtime+0x35/0x200
[89479.106662]  [<c013d7eb>] ? trace_hardirqs_off+0xb/0x10
[89479.106892]  [<dfe7faa7>] ? usb_hcd_irq+0x97/0xa0 [usbcore]
[89479.106926]  [<c015ba79>] handle_IRQ_event+0x29/0x60
[89479.106947]  [<c015cf89>] handle_level_irq+0x69/0xe0
[89479.106963]  [<c015cf20>] ? handle_level_irq+0x0/0xe0
[89479.106977]  <IRQ>  [<c02ca933>] ? tcp_v4_rcv+0x633/0x6e0
[89479.107025]  [<c0103f0c>] ? common_interrupt+0x28/0x30
[89479.107057]  [<c02a0000>] ? sk_run_filter+0x320/0x7a0
[89479.107078]  [<c020e041>] ? list_del+0x21/0x90
[89479.107106]  [<dfd0d24e>] ? orinoco_rx_isr_tasklet+0x2ce/0x480 [orinoco]
[89479.107131]  [<c01402e0>] ? __lock_acquire+0x160/0x1650
[89479.107151]  [<c01073d0>] ? native_sched_clock+0x20/0x70
[89479.107169]  [<c013d825>] ? lock_release_holdtime+0x35/0x200
[89479.107200]  [<c012249a>] ? irq_enter+0xa/0x60
[89479.107217]  [<c0104e52>] ? do_IRQ+0xd2/0x130
[89479.107518]  [<c010342c>] ? restore_nocheck_notrace+0x0/0xe
[89479.107542]  [<c0122830>] ? __do_softirq+0x0/0x110
[89479.107561]  [<c013f7b4>] ? trace_hardirqs_on_caller+0x74/0x140
[89479.107583]  [<c01ff678>] ? trace_hardirqs_on_thunk+0xc/0x10
[89479.107602]  [<c0122087>] ? tasklet_action+0x27/0x90
[89479.107620]  [<c013f7b4>] ? trace_hardirqs_on_caller+0x74/0x140
[89479.107638]  [<c01220a3>] ? tasklet_action+0x43/0x90
[89479.107655]  [<c012289f>] ? __do_softirq+0x6f/0x110
[89479.107674]  [<c0122830>] ? __do_softirq+0x0/0x110
[89479.107685]  <IRQ>  [<c015cf20>] ? handle_level_irq+0x0/0xe0
[89479.107715]  [<c012246d>] ? irq_exit+0x5d/0x80
[89479.107732]  [<c0104e52>] ? do_IRQ+0xd2/0x130
[89479.107747]  [<c0103337>] ? sysenter_exit+0xf/0x16
[89479.107765]  [<c013f83d>] ? trace_hardirqs_on_caller+0xfd/0x140
[89479.107782]  [<c0103f0c>] ? common_interrupt+0x28/0x30
[89479.107797] ---[ end trace a1fc0a52df4a729d ]---
Reported-by: NAndrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: NDavid Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CONFIG_ATH9K=y results in build issues if CONFIG_RFKILL=m since ath9k
does not depend on rfkill in kconfig (i.e., CONFIG_RFKILL is used to
select whether to enable rfkill in ath9k), but uses its functions if
rfkill is enabled. Enforce ath9k to be build as a module if
CONFIG_RFKILL=m to avoid this invalid configuration.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the USB ID for Thomson Speedtouch 121g to p54usb.
Signed-off-by: NMichiel <michiel@ettema.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The short preamble mode was not correctly detected during TX,
rt2x00 used the rate->hw_value_short field but mac80211 is not
using this field that way.
Instead the flag IEEE80211_TX_RC_USE_SHORT_PREAMBLE should be
used to determine if the frame should be send out using
short preamble or not.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

add USB ID for the Linksys WUSB200 Wireless-G Business USB Adapter to
rt73usb.
Signed-off-by: NStefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On x86_64 architecture with 4K page size and SLUB debugging enabled, stress
testing on p54usb has resulted in skb allocation failures of O(1) and extreme
page fragmentation. Reducing rx_mtu fixes this problem by reducing the size of
all receive skb allocations to be of O(0). This change does not impact
performance in any way.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since "rt2x00: Fix LED state handling", rt2x00leds_led_radio wrongly
checks that the LED type is LED_TYPE_ASSOC. This patch makes it check
for LED_TYPE_RADIO once again.
Signed-off-by: NAndrew Price <andy@andrewprice.me.uk>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Raytheon cards use 2.4 GHz, not 2.4 MHz.
See http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Linux.Wireless.drivers.html#RaylinkSigned-off-by: NErik Ekman <erik@kryo.se>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The UCC Event Register (UCCE) already has unambigous macro definitions in qe.h,
so we should not be defining our own in the UCC Ethernet driver.

Removed unused local variable 'dev' from ucc_geth_poll(), which fixes
a warning caused by commit 908a7a16
("net: Remove unused netdev arg from some NAPI interfaces.").

Replaced in_be/out_be pairs with setbits32 or clrbits32, where applicable.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I have a system with a Chelsio adapter (driven by cxgb3) whose ports are
part of a Linux bridge.  Recently I updated the kernel and discovered
that things stopped working because cxgb3 was doing LRO on packets that
were passed into the bridge code for forwarding.  (Incidentally, this
problem manifested itself in a strange way that made debugging a bit
interesting -- for some reason, the skb_warn_if_lro() check in bridge
didn't trigger and these LROed packets were forwarded out a forcedeth
interface, and caused the forcedeth transmit path to get stuck)

This is because cxgb3 has no way of keeping state for the LRO flag until
the interface is brought up, so if the bridging code disables LRO while
the interface is down, then cxgb3_up() will just reenable LRO, and on my
Debian system at least, the init scripts add interfaces to a bridge
before bringing the interfaces up.

Fix this by keeping track of each interface's LRO state in cxgb3 so that
when bridge disables LRO, it stays disabled in cxgb3_up() when the
interface is brought up.  I did this by changing the rx_csum_offload
flag into a pair of bit flags; the effect of this on the rx_eth() fast
path is miniscule enough that it should be fine (eg on x86, a cmpb
instruction becomes a testb instruction).
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only the SFX7101 requires software power control.  This was
incorrectly being applied to the SFT9001 rev A as well.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change lets "cat /proc/interrupts" show the name of the ethernet
device (e.g. eth0) rather than the driver name (smsc911x).
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

if this code path is ever hit, the platform_data struct isn't properly
configured with a bus width flag so the device won't work (hence the
BUG()).

This patch adds a dummy return statement to eliminate this compiler
warning:

drivers/net/smsc911x.c: In function 'smsc911x_reg_read':
drivers/net/smsc911x.c:148: warning: control reaches end of non-void function
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a potential race condition between scheduling napi and
completing napi poll. The call to netif_rx_schedule should be under
protection of the lock (as is the completion), otherwise, interrupts
could be masked off.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the feature flag for mgmt unit as it is not used for
this chipset.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to sleep while waiting for the hardware
semaphore to become available.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support for dev id 8000 is pushed out until 2.6.30.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Putting back ql_read_sh_reg() function and using rmb() instead of
volatile.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch bumps up the version number and adds current year to copyright.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a potential race condition between xmit thread and xmit
completion thread. The calculation of empty tx descriptors is not
performed under the lock. This could cause it to set the stop flag while
the completion thread finishes all tx's. This will result in the tx
queue in stopped state and no one to wake it up.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some devices were converted incorrectly and are missing the validate
address hooks.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many drivers lost the ability to set ethernet address accidently
during the net_device_ops conversion.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the same kind of wrapper that can also be found in many
other network device drivers.

Tested with a freescale MPC8349E host CPU:
Toggled the interface LEDs on a DP83865 PHY.
Signed-off-by: NClifford Wolf <clifford@clifford.at>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.  I have also taken advantage of the availability
of the value of priv->dev in the subsequent calls to netif_stop_queue and
netif_carrier_off.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@

- T i = E->fld;
+ T i;
  ... when != E
      when != i
  if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@

- T i = E->fld;
+ T i;
  ... when != E
      when != i
  if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set this bit by calling device_set_wakeup_enable().

This restores proper WOL for the 3c59x driver.
Reported-and-tested-by: NGraeme Wilford <gwilford@gmail.com>
Reported-by: NGunnar Degnbol <degnbol@danbbs.dk>
Signed-off-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Name interrupt vectors according to the new naming standard, by Robert
Olsson and DaveM.

The qlge driver were very close to the new standard, thus the change
is kind of trivial.
Signed-off-by: NJesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom 4400 puts a header of configurable size (apparently needs
to be at least 28 bytes) in front of received packets. When handling
this, the previous code accidentally added the offset 30 *twice* for
the software and once for the hardware, thereby cancelling out the
IP alignment effect of the 30 byte padding and wasting an additional
30 bytes of memory per packet.

This patch fixes this problem and improves routing throughput by
about 30% on MIPS, where unaligned access is expensive.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds process name of the current mutex holder to the WARN message output
when the e1000e driver attempts to acquire the nvm_mutex and finds that
it is already being held. With this patch the WARN message indicates
both the process name of the current mutex holder and the process name of
the attempted acquisition, which together will help to identify the
contending codepaths.
Signed-off-by: NDavid Graham <david.graham@intel.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump version to 0.21 and release date to 09Jan2009.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We do not depend on EXPERIMENTAL and the driver is
not experimental, so remove this warning.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes the ethernet driver assign a random ethernet
MAC address when the bootloader does not set it.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>