We only need to set the skb queue twice:

1. by the netdev, on local TX.
2. when forwarding a mesh frame.

We only need to set the qos header twice:

1. by mac80211, on local TX.
2. when putting a frame on the mpath->frame_queue

We also don't need the RA in order to set the proper queue mapping since
all mesh STAs are QoS, indicate this and do it once when the frame is
received. Also fixes an issue where the QoS header and queue mapping was not
set for unicast forwarded frames.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There was an an implicit assumption that any QoS data frame received
from a STA/TID with an active BA session was sent to this vif as part of
a BA.  This is not true if IFF_PROMISC is enabled and the frame was
destined for a different peer, for example. Don't treat these frames as
part of a BA from the sending STA.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously QoS multicast frames had the Normal Acknowledgment QoS
control bits set. This would cause broadcast frames to be discarded by
peers with which we have a BA session, since their sequence number would
fall outside the allowed range. Set No Ack QoS control bits on multicast
QoS frames and filter these in de-aggregation code.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>

v2: Use proper QoS Ack Policy ctl field mask (Christian)

v3: Clean up conditional (Johannes)
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't accept redundant PREQs for a given destination. This fixes a
problem under high load:

kernel: [20386.250913] mesh_queue_preq: 235 callbacks suppressed
kernel: [20386.253335] Mesh HWMP (mesh0): PREQ node queue full
kernel: [20386.253352] Mesh HWMP (mesh0): PREQ node queue full
(...)

The 802.11s protocol has a provision to limit the rate of path requests
(PREQs) are transmitted (dot11MeshHWMPpreqMinInterval) but there was no
limit on the rate at which PREQs were being queued up.  There is a valid
reason for queuing PREQs: this way we can even out PREQ bursts.  But
queueing multiple PREQs for the same destination is useless.
Reported-by: NPedro Larbig <pedro.larbig@carhs.de>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver is never informed about monitor or
AP_VLAN interfaces, so whenever we pass those
to it later this is a bug. Verify we don't as
there are some cases where this could happen.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 802.1X EAPOL handshake hostapd does requires
knowing whether the frame was ack'ed by the peer.
Currently, we fudge this pretty badly by not even
transmitting the frame as a normal data frame but
injecting it with radiotap and getting the status
out of radiotap monitor as well. This is rather
complex, confuses users (mon.wlan0 presence) and
doesn't work with all hardware.

To get rid of that hack, introduce a real wifi TX
status option for data frame transmissions.

This works similar to the existing TX timestamping
in that it reflects the SKB back to the socket's
error queue with a SCM_WIFI_STATUS cmsg that has
an int indicating ACK status (0/1).

Since it is possible that at some point we will
want to have TX timestamping and wifi status in a
single errqueue SKB (there's little point in not
doing that), redefine SO_EE_ORIGIN_TIMESTAMPING
to SO_EE_ORIGIN_TXSTATUS which can collect more
than just the timestamp; keep the old constant
as an alias of course. Currently the internal APIs
don't make that possible, but it wouldn't be hard
to split them up in a way that makes it possible.

Thanks to Neil Horman for helping me figure out
the functions that add the control messages.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since local->tmp_channel is always NULL in one branch, some code paths
will newer be taken in that branch, so remove them.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Janusz reported that the EOSP bit in mac80211 was
getting cleared all the time. I had not found this
since I tested uAPSD with a device that always set
the bit itself. Preserve the bit when building the
QoS header.
Reported-by: NJanusz Dziedzic <janusz.dziedzic@gmail.com>
Tested-by: NJanusz Dziedzic <janusz.dziedzic@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

WPI-SMS4 uses 16-octet PN field, so we need to allow longer key
sequence values to be configured.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The vif might be busy while reconfiguring
(e.g. associated), so indicate BSS_CHANGED_IDLE as well.
Reported-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

802.11n-2009 extends the supported rates element with a
magic value which can be used to prevent legacy stations
from joining the BSS.

However, this magic value is not a rate like the others
and the magic can simply be ignored/skipped at this late
stage.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>---
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that pending commands are hci_dev specific there's no need to check
whether a command matches hci_dev when iterating through them.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

For consistency the integer type should be u16 and not __u16.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The cancel_delayed_work_sync function should not be used if we hold any
locks. Luckily all places where this is the case it is also safe to use
the non-sync version.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Now that the pending commands are within struct hci_dev we can properly
control access to them throught the hci_dev locking mechanism.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch moves the pending management command list (previously global
to mgmt.c) into struct hci_dev. This makes it possible to do proper
locking when accessing it (through the existing hci_dev locks) and
thereby avoid race conditions.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The current global pending command list in mgmt.c is racy. Possibly the
simplest way to fix it is to have per-hci dev lists instead of a global
one (all commands that need a pending struct are hci_dev specific).
This way the list can be protected using the already existing per-hci
dev lock. To enable this refactoring the first thing that needs to be
done is to ensure that the mgmt functions have access to the hci_dev
struct (instead of just the dev id).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NAshok Nagarajan <anagar6@uic.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set peer's HT capabilities, and disallow peering if we're on a different
channel type.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NAshok Nagarajan <anagar6@uic.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NAshok Nagarajan <anagar6@uic.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some refactoring for IBSS HT.

Move HT info and capability IEs building code into separate functions.

Add function to get the channel type from an HT info IE.
Signed-off-by: NAlexander Simon <an.alexsimon@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove most references to magic numbers, save a few bytes and hopefully
improve readability.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some cards can generate CCMP IVs in HW, but require the space for the IV
to be pre-allocated in the frame at the correct offset. Add a key flag
that allows us to achieve this.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

genlmsg_end() cannot fail, it just returns the length
of the message. Thus, error handling for it is useless.
While removing it, I also noticed a useless variable
and removed this it as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If there are no cooked monitor interfaces, there's
no point in building the radiotap RX header for the
frame and iterating the interface list.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's an extra pair of parentheses here that
is simply confusing because it implies a nesting
that doesn't actually exist. Just remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 calls ieee80211_set_wmm_default (which in turn
calls drv_conf_tx()) for every new interface, including
"internal" ones (e.g. monitor interface, which the low-level
driver doesn't know about).

Limit this call only to valid interfaces.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds address type info (typically BR/EDR vs LE) to management
messages that need this. This also ensures conformance to the latest
management API specification.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

BR/EDR link keys have their own commands and events (separate from SMP)
and the remove_keys command (previously remove_key) removes keys of any
kind for the specified remote address.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

We should return a ENETDOWN status response if the adapter is powered
off (i.e. the HCI_UP flag isn't set).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

There's no need to deal with mgmt_pending_cmd when blocking and
unblocking devices since these actions are synchronous.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The power off code doesn't need to use its own custom timer since the
delayed_work API provides the exact same functionality.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

A proper mgmt_command_status should be returned to user-space if either
discoverable or connectable enabling fails.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Based on the revised mgmt API set_discoverable has a timeout parameter
to specify how long the adapter will remain discoverable. A value of 0
means "indefinitively".
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

By using periodic inquiry command we're not able to detect correctly
when the controller has started inquiry.

Today we have this workaround in inquiry result event handler
to set the HCI_INQUIRY flag when it sees the first inquiry result
event. This workaround isn't enough because the device may be
performing an inquiry but the HCI_INQUIRY flag is not set. For
instance, if there is no device in range, no inquiry result event
is generated, consequently, the HCI_INQUIRY flags isn't set when
it should so.

We rely on HCI_INQUIRY flag to implement the discovery procedure
properly. So, as we aren't able to clear/set the HCI_INQUIRY flag
in a reliable manner, periodic inquiry events shouldn't change
the HCI_INQUIRY flag.

Thus, due to that issue and in order to keep compatibility with
userspace, periodic inquiry events shouldn't send mgmt discovering
events.

In future, we might track if periodic inquiry is enabled or not.
By tracking this state we'll be able to do some improvements in
Discovery such as failing MGMT_OP_START_DISCOVERY command in case
periodic inquiry is on. We can also send no mgmt_device_found
event if periodic inquiry is on.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds a function to hci_core to cancel an ongoing inquiry.

According to the Bluetooth spec, the inquiry cancel command should
only be issued after the inquiry command has been issued, a command
status event has been received for the inquiry command, and before
the inquiry complete event occurs.

As HCI_INQUIRY flag is only set just after an inquiry command status
event occurs and it is cleared just after an inquiry complete event
occurs, the inquiry cancel command should be issued only if HCI_INQUIRY
flag is set.

Additionally, cancel inquiry related code from stop_discovery() were
replaced by a hci_cancel_inquiry() call.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds a function to hci_core to carry out inquiry.

All inquiry code from start_discovery() were replaced by a
hci_do_inquiry() call.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Add parsing Extended Flow Specification in L2CAP Config Response.
Based upon haijun.liu <haijun.liu@atheros.com> series of patches
(sent Sun, 22 Aug 2010)
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>