Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The "lazy writeout" of cleared bitmap pages happens during resync, and
should happen again once the resync finishes cleanly, or is aborted.

If resync finished cleanly, or was aborted because of peer disk
failure, we trigger the writeout from worker context in the after
state change work.

If resync was aborted because of connection failure, we should not
immediately trigger bitmap writeout, but rather postpone the
writeout to after the connection cleanup happened.  We now do it
in the receiver context from drbd_disconnect().

If resync was aborted because of local disk failure, well, there
is nothing to write to anymore.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Protocol A has no P_WRITE_ACKs, but has P_NEG_ACKs.
The master bio might already be completed, therefore the
request is no longer in the collision hash.
=> Do not try to validate block_id as request

In Protocol B we might already have got a P_RECV_ACK
but then get a P_NEG_ACK after wards.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The point is that drbd_disconnect() can be called with a cstate of
WFConnection.

That happens if the user issues "drbdsetup disconnect" while the
drbd_connect() function executes. Then drbdd_init() will call
drbdd(), which in turn will return without receiving any
packets. Then drbdd_init() will end up calling drbd_disconnect()
with a cstate of WFConnection.

Bottom line: This assertion is wrong as it is, and we do not
see value in fixing it. => Removing it.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The test if rs_pending_cnt == 0 was too weak. Using Test for
unacked_cnt == 0 instead. Moved that into the worker.

Since unacked_cnt gets already increased when an P_RS_DATA_REQ
comes in.

Also using a timer to make Ahead -> SyncSource -> Ahead cycles
slower...
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

See also commit from 2009-08-15
"drbd_uuid_compare(): Do not full sync in case a P_SYNC_UUID packet gets lost."

We saw cases where the History UUIDs where not as expected. So the
detection of the special case did not trigger. With the sync UUID
no longer being a random number, but deducible from the previous
bitmap UUID, the detection of this special case becomes more
reliable.

The SyncUUID now is the previous bitmap UUID + 0x1000000000000.

Rule 5a:
Cs = H1p & H1p + Offset = Bp
  Connection was lost before SyncUUID Packet came through.
  Corrent (peer) UUIDs:
   Bp = H1p
   H1p = H2p
   H2p = 0
  Become Sync target.

Rule 7a:
Cp = H1s & H1s + Offset = Bs
  Connection was lost before SyncUUID Packet came through.
  Correct (own) UUIDs:
   Bs = H1s
   H1s = H2s
   H2s = 0
  Become Sync source.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

We may not get from SyncSource to Ahead if we have sent some
P_RS_DATA_REPLY packets to the peer and are waiting for
P_WRITE_ACK.

Again, this is not relevant for proper tuned systems, but makes
sure that the not-tuned system does not get diverging bitmaps.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

When the sync source node replies to a P_RS_DATA_REQUEST packet
when it is already in ahead mode. I.e. those two packets
crossed each other on the wire, that may lead to diverging
bitmaps.

  This never happens in a well-tuned-system. In a well-tuned-
  system the resync controller has reduced the resync speed
  to zero long before we got into ahead-mode.

But we have to be prepared for the not-well-tuned-system
of course as well.
Because -> diverging bitmaps = non terminating resync.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

We expect to only receive the recently introduced "set out of sync"
packets in specific states. If we receive them in different states, that
may confuse the resync process to the point where it won't terminate, or
think it made negative progress.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The FAULT_ACTIVE macro just wraps the drbd_insert_fault macro for no
apparent reason.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

* C_STARTING_SYNC_S, C_STARTING_SYNC_T In these states the bitmap gets
  written to disk. Locking out of app-IO is done by using the
  drbd_queue_bitmap_io() and drbd_bitmap_io() functions these days.
  It is no longer necessary to lock out app-IO based on the connection
  state.
  App-IO that may come in after the BITMAP_IO flag got cleared before the
  state transition to C_SYNC_(SOURCE|TARGET) does not get mirrored, sets
  a bit in the local bitmap, that is already set, therefore changes nothing.

* C_WF_BITMAP_S In this state we send updates (P_OUT_OF_SYNC packets).
  With that we make sure they have the same number of bits when going
  into the C_SYNC_(SOURCE|TARGET) connection state.

* C_UNCONNECTED: The receiver starts, no need to lock out IO.

* C_DISCONNECTING: in drbd_disconnect() we had a wait_event()
  to wait until ap_bio_cnt reaches 0. Removed that.

* C_TIMEOUT, C_BROKEN_PIPE, C_NETWORK_FAILURE
  C_PROTOCOL_ERROR, C_TEAR_DOWN: Same as C_DISCONNECTING

* C_WF_REPORT_PARAMS: IO still possible since that is still
  like C_WF_CONNECTION.

And we do not need to send barriers in C_WF_BITMAP_S connection state.

Allow concurrent accesses to the bitmap when receiving the bitmap.
Everything gets ORed anyways.

A drbd_free_tl_hash() is in after_state_chg_work(). At that point
all the work items of the last connections must have been processed.

Introduced a call to drbd_free_tl_hash() into drbd_free_mdev()
for paranoia reasons.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

We only issue resync requests if there is no significant application IO
going on. = Application IO has higher priority than resnyc IO.

If application IO can not be started because the resync process locked
an resync_lru entry, start the IO operations necessary to release the
lock ASAP.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

In this connection mode, the ahead node no longer replicates
application IO. The behind's disk becomes out dated.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

To ease tracking of bios in some hash tables, we want it to
not cross certain boundaries (128k, used to be 32k).
We limit the maximum bio size using queue parameters.

Historically some defines and variables we use there have been named
max_segment_size, which was misguided. Rename them to max_bio_size,
and use [blk_]queue_max_hw_sectors where appropriate.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

With data-integrity digest enabled, double-check on the sending side
for modifications by upper layers of buffers under write back,
so we can tell it appart from corruption on the "wire".
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Show progressbar and ETA always, with proc_details >= 1 also show the
current sector position for both resync and online-verify on both nodes.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

For partial (resumed) online verify, initialize the resync step marks
once we know what the online verify start sector is.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

For a partial (resumed) online-verify, initialize rs_total not to total
bits, but to number of bits to check in this run, to match the meaning
rs_total has for actual resync.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

With the plugging now being explicitly controlled by the
submitter, callers need not pass down unplugging hints
to the block layer. If they want to unplug, it's because they
manually plugged on their own - in which case, they should just
unplug at will.
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

This should fix a performance degradation we observed recently.

If we don't expect any subheader, we should not call into the tcp stack,
as that may add considerable latency if there is no data available at
this point.

For a synthetic synchronous write load with single outstanding writes,
this additional latency when processing the "unplug remote" packet
added up to a performance degradation factor >= 10.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The big kernel lock has been removed from all these files at some point,
leaving only the #include.

Remove this too as a cleanup.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>