Many locations within the driver would use an inconsistent set of
checks to determine ISP-reset state.  Consolidate the checks into
this inline-helper.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

NULL orom ptr passed in for verification which caused page fault.
We will set a default version when we don't have orom struct.
Reported-by: NDan Melnic <dan@seamicro.com>
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

In some scenarios, an EEH error can take a long time to be detected, since the
driver issues an MMIO read only after a device reset command times out and we
try to reset the adapter. This patch adds some code in ipr_cancel_op() to read
a hardware register so we detect the error earlier in case the op is being
aborted because of a timeout caused by a frozen adapter slot.

Another problem in such scenarios is that in __ipr_eh_host_reset() we change the
dump state flag from WAIT_FOR_DUMP to GET_DUMP, and the flag is later changed
from GET_DUMP to READ_DUMP in ipr_reset_restore_cfg_space(). However, if when
__ipr_eh_host_reset() is called by the SCSI error handling the function
ipr_reset_restore_cfg_space() has already been called by the PCI EEH code, we
end up with the flag in an inconsistent state. This patch also prevents this
problem.
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If ioc->pci_error_recovery is set, goto out in mpt2sas_base_hard_reset_handler()
leads to unlock unheld ioc->reset_in_progress_mutex.

The patch fixes the issue by jumping afer mutex_unlock() call.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The current error handling doesn't work because we flash_part is a u32
so the checks for negative error codes don't work.  I considered making
things signed but I don't know the hardware enough to say if that's a
problem.  Really, we don't use the error codes so just returning zero
for all problems is fine.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We use len to store the return value from eth_header().  eth_header()
can return -ETH_HLEN (-14).  We want to pass this back instead of
truncating it to 65522 and returning that.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Treat pwmX as a measured value, not as a (mostly static) limit value, so
that it is updated more frequently from the device register.
Signed-off-by: NNikolaus Schulz <mail@microschulz.de>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

The receive FIFO wakeup latency estimate in the omap-serial driver is
three orders of magnitude too small.  This effectively prevents the
MPU from going to a low-power state when CONFIG_CPU_IDLE=y.  This is a
major power management regression and masks some other FIFO-related
bugs in the driver.

Fix by correcting the most egregious problem in the RX wakeup latency
estimate.  There are several other flaws in the estimator; these will
be fixed by a separate patch series intended for 3.4.

The difference in low-power states with this patch can be observed via
debugfs in pm_debug/count.

This estimate does not have any effect when CONFIG_CPU_IDLE=n.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: NGovindraj.R <govindraj.raja@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prevent OMAP UARTs from going idle while they are still transferring
data in PIO mode.  This works around an oversight in the OMAP UART
hardware present in OMAP34xx and earlier: an idle UART won't send a
wakeup when the TX FIFO threshold is reached.  This causes long delays
during data transmission when the MPU powerdomain enters a low-power
mode.  The MPU interrupt controller is not able to respond to
interrupts when it's in a low-power state, so the TX buffer is not
refilled until another wakeup event occurs.

This fix changes the erratum i291 DMA idle workaround.  Rather than
toggling between force-idle and no-idle, it will toggle between
smart-idle and no-idle.  The important part of the workaround is the
no-idle part, so this shouldn't result in any change in behavior.

This fix should work on all OMAP UARTs.  Future patches intended for
the 3.4 merge window will make this workaround conditional on a
"feature" flag, and will use the OMAP36xx+ TX event wakeup support.

Thanks to Kevin Hilman <khilman@ti.com> for mentioning the erratum i291
workaround, which led to the development of this approach.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NGovindraj.R <govindraj.raja@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the (default) PIO mode, use a one-byte RX FIFO threshold.  The OMAP
UART IP blocks do not appear to be capable of waking the system under
an RX timeout condition.  Since the previous RX FIFO threshold was 16
bytes, this meant that omap-serial.c did not become aware of any
received data until all those bytes arrived or until another UART
interrupt occurred.  This made the serial console and presumably other
serial applications (GPS, serial Bluetooth) unusable or extremely
slow.  A 1-byte RX FIFO threshold also allows the MPU to enter a
low-power consumption state while waiting for the FIFO to fill.

This can be verified using the serial console by comparing the
behavior when "0123456789abcde" is pasted in from another window, with
the behavior when "0123456789abcdef" is pasted in.  Since the former
string is less than sixteen bytes long, the string is not echoed for
some time, while the latter string is echoed immediately.

DMA operation is unaffected by this patch.

Thanks to Russell King - ARM Linux <linux@arm.linux.org.uk> for some
additional information on the standard behavior of the RX timeout
event, which was used to improve this commit description.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Govindraj Raja <govindraj.r@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the number of tx/rx queues changes the ethtool ioctl
ETHTOOL_GSTATS may overrun the userspace buffer. This
occurs because the general practice in user space to
query stats is to issue a ETHTOOL_GSSET cmd to learn the
buffer size needed, allocate the buffer, then call
ETHTOOL_GSTIRNGS and ETHTOOL_GSTATS. If the number of
real_num_queues is changed or flow control attributes
are changed after ETHTOOL_GSSET but before the
ETHTOOL_GSTRINGS/ETHTOOL_GSTATS a user space buffer
overrun occurs.

To fix the overrun always return the max buffer size
needed from get_sset_count() then return all strings
and stats from get_strings()/get_ethtool_stats().

This _will_ change the output from the ioctl() call
which could break applications and script parsing in
theory. I believe these changes should not break existing
tools because the only changes will be more {tx|rx}_queues
and the {tx|rx}_pb_* stats will always be returned.
Existing scripts already need to handle changing number
of queues because this occurs today depending on system
and current features. The {tx|rx}_pb_* stats are at the
end of the output and should be handled by scripts today
regardless.

Finally get_ethtool_stats and get_strings are free-form
outputs tools parsing these outputs should be defensive
anyways. In the end these updates are better then
having a tool segfault because of a buffer overrun.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Users expect the up2tc mapping to be maintained across a DCB
enable/disable/enable transition. And since we maintain all
the other DCB attributes we should do this for up2tc mappings
as well just to be consistent. Also without this we break
user space applications that expect this to occur that
previously worked.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the netdev is already in NETREG_UNREGISTERING/_UNREGISTERED state, do not
update the real num tx queues. netdev_queue_update_kobjects() is already
called via remove_queue_kobjects() at NETREG_UNREGISTERING time. So, when
upper layer driver, e.g., FCoE protocol stack is monitoring the netdev
event of NETDEV_UNREGISTER and calls back to LLD ndo_fcoe_disable() to remove
extra queues allocated for FCoE, the associated txq sysfs kobjects are already
removed, and trying to update the real num queues would cause something like
below:

...
PID: 25138  TASK: ffff88021e64c440  CPU: 3   COMMAND: "kworker/3:3"
 #0 [ffff88021f007760] machine_kexec at ffffffff810226d9
 #1 [ffff88021f0077d0] crash_kexec at ffffffff81089d2d
 #2 [ffff88021f0078a0] oops_end at ffffffff813bca78
 #3 [ffff88021f0078d0] no_context at ffffffff81029e72
 #4 [ffff88021f007920] __bad_area_nosemaphore at ffffffff8102a155
 #5 [ffff88021f0079f0] bad_area_nosemaphore at ffffffff8102a23e
 #6 [ffff88021f007a00] do_page_fault at ffffffff813bf32e
 #7 [ffff88021f007b10] page_fault at ffffffff813bc045
    [exception RIP: sysfs_find_dirent+17]
    RIP: ffffffff81178611  RSP: ffff88021f007bc0  RFLAGS: 00010246
    RAX: ffff88021e64c440  RBX: ffffffff8156cc63  RCX: 0000000000000004
    RDX: ffffffff8156cc63  RSI: 0000000000000000  RDI: 0000000000000000
    RBP: ffff88021f007be0   R8: 0000000000000004   R9: 0000000000000008
    R10: ffffffff816fed00  R11: 0000000000000004  R12: 0000000000000000
    R13: ffffffff8156cc63  R14: 0000000000000000  R15: ffff8802222a0000
    ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0018
 #8 [ffff88021f007be8] sysfs_get_dirent at ffffffff81178c07
 #9 [ffff88021f007c18] sysfs_remove_group at ffffffff8117ac27
#10 [ffff88021f007c48] netdev_queue_update_kobjects at ffffffff813178f9
#11 [ffff88021f007c88] netif_set_real_num_tx_queues at ffffffff81303e38
#12 [ffff88021f007cc8] ixgbe_set_num_queues at ffffffffa0249763 [ixgbe]
#13 [ffff88021f007cf8] ixgbe_init_interrupt_scheme at ffffffffa024ea89 [ixgbe]
#14 [ffff88021f007d48] ixgbe_fcoe_disable at ffffffffa0267113 [ixgbe]
#15 [ffff88021f007d68] vlan_dev_fcoe_disable at ffffffffa014fef5 [8021q]
#16 [ffff88021f007d78] fcoe_interface_cleanup at ffffffffa02b7dfd [fcoe]
#17 [ffff88021f007df8] fcoe_destroy_work at ffffffffa02b7f08 [fcoe]
#18 [ffff88021f007e18] process_one_work at ffffffff8105d7ca
#19 [ffff88021f007e68] worker_thread at ffffffff81060513
#20 [ffff88021f007ee8] kthread at ffffffff810648b6
#21 [ffff88021f007f48] kernel_thread_helper at ffffffff813c40f4
Signed-off-by: NYi Zou <yi.zou@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes an issue in which RSC will generate corrupted frames when
PAGE_SIZE is larger than 8K.  Specifically it looks like that in 2.6.39 a
change was made so that GRO would always have at least 16 frags available
for coalescing, but the ixgbe RSC logic was not updated.  As such the RSC
feature would generate a frame larger than 64K and then overflow the value
in the IP length field.

To correct that I am now basing things on the PAGE_SIZE.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A check for the number of VFs allocated should have used a greater than
equal operator instead of just greater than.  This caused allocation of
exactly 32 VFs to not enable the PF transmit and receive enables.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NRobert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Recent addition of code to find already allocated VFs failed to take
account that systems with 2 or more multi-port SR-IOV capable controllers
might have already enabled VFs.  Make sure that the VFs the function is
finding are actually subordinate to the particular instance of the adapter
that is looking for them and not subordinate to some device that has
previously enabled SR-IOV.

This bug exists in 3.2 stable as well as 3.3 release candidates.

CC: stable@vger.kernel.org
Reported-by: NDavid Ahern <daahern@cisco.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NRobert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Recent addition of code to find already allocated VFs failed to take
account that systems with 2 or more multi-port SR-IOV capable controllers
might have already enabled VFs.  Make sure that the VFs the function is
finding are actually subordinate to the particular instance of the adapter
that is looking for them and not subordinate to some device that has
previously enabled SR-IOV.

This is applicable to 3.2+ kernels.

CC: stable@vger.kernel.org
Reported-by: NDavid Ahern <daahern@cisco.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NRobert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit d5bc77a2 broke Wake-on-LAN by
inadvertently dropping the enabling of DMA receives.

Restore the enabling of DMA receives for WoL.

This is applicable to 3.1+ stable trees.

CC: stable@vger.stable.org
Reported-by: NTobias Klausmann <klausman@schwarzvogel.de>
Signed-off-by: NDean Nelson <dnelson@redhat.com>
Tested-by: NTobias Klausmann <klausman@schwarzvogel.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to extract the high byte of the 16-bit word, shift the word to
the right, not to the left.
Signed-off-by: NNikolaus Schulz <mail@microschulz.de>
Cc: stable@kernel.org # 2.6.32+
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Unlike the other chips supported by this driver, the F75387 stores the
pwm_mode in register F75375_REG_FAN_TIMER, not F75375_REG_CONFIG1.
Signed-off-by: NNikolaus Schulz <mail@microschulz.de>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

In order to enable temperature mode aka automatic mode for the F75373 and
F75375 chips, the two FANx_MODE bits in the fan configuration register
need be set to 01, not 10.
Signed-off-by: NNikolaus Schulz <mail@microschulz.de>
Cc: stable@kernel.org # 2.6.32+
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Commit ec3e5a16 slipped in some duplicate code.
Remove it.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

This fixes a memory-corrupting bug: not only does it cause the warning,
but as a result of dropping the refcount to zero, it causes the
pcmcia_socket0 device structure to be freed while it still has
references, causing slab caches corruption.  A fatal oops quickly
follows this warning - often even just a 'dmesg' following the warning
causes the kernel to oops.

While testing suspend/resume on an ARM device with PCMCIA support, and a
CF card inserted, I found that after five suspend and resumes, the
kernel would complain, and shortly die after with slab corruption.

  WARNING: at include/linux/kref.h:41 kobject_get+0x28/0x50()

As the message doesn't give a clue about which kobject, and the built-in
debugging in drivers/base/power/main.c happens too late, this was added
right before each get_device():

  printk("%s: %p [%s] %u\n", __func__, dev, kobject_name(&dev->kobj), atomic_read(&dev->kobj.kref.refcount));

and on the 3rd s2ram cycle, the following behaviour observed:

On the 3rd suspend/resume cycle:

  dpm_prepare: c1a0d998 [pcmcia_socket0] 3
  dpm_suspend: c1a0d998 [pcmcia_socket0] 3
  dpm_suspend_noirq: c1a0d998 [pcmcia_socket0] 3
  dpm_resume_noirq: c1a0d998 [pcmcia_socket0] 3
  dpm_resume: c1a0d998 [pcmcia_socket0] 3
  dpm_complete: c1a0d998 [pcmcia_socket0] 2

4th:

  dpm_prepare: c1a0d998 [pcmcia_socket0] 2
  dpm_suspend: c1a0d998 [pcmcia_socket0] 2
  dpm_suspend_noirq: c1a0d998 [pcmcia_socket0] 2
  dpm_resume_noirq: c1a0d998 [pcmcia_socket0] 2
  dpm_resume: c1a0d998 [pcmcia_socket0] 2
  dpm_complete: c1a0d998 [pcmcia_socket0] 1

5th:

  dpm_prepare: c1a0d998 [pcmcia_socket0] 1
  dpm_suspend: c1a0d998 [pcmcia_socket0] 1
  dpm_suspend_noirq: c1a0d998 [pcmcia_socket0] 1
  dpm_resume_noirq: c1a0d998 [pcmcia_socket0] 1
  dpm_resume: c1a0d998 [pcmcia_socket0] 1
  dpm_complete: c1a0d998 [pcmcia_socket0] 0
  ------------[ cut here ]------------
  WARNING: at include/linux/kref.h:41 kobject_get+0x28/0x50()
  Modules linked in: ucb1x00_core
  Backtrace:
  [<c0212090>] (dump_backtrace+0x0/0x110) from [<c04799dc>] (dump_stack+0x18/0x1c)
  [<c04799c4>] (dump_stack+0x0/0x1c) from [<c021cba0>] (warn_slowpath_common+0x50/0x68)
  [<c021cb50>] (warn_slowpath_common+0x0/0x68) from [<c021cbdc>] (warn_slowpath_null+0x24/0x28)
  [<c021cbb8>] (warn_slowpath_null+0x0/0x28) from [<c0335374>] (kobject_get+0x28/0x50)
  [<c033534c>] (kobject_get+0x0/0x50) from [<c03804f4>] (get_device+0x1c/0x24)
  [<c0388c90>] (dpm_complete+0x0/0x1a0) from [<c0389cc0>] (dpm_resume_end+0x1c/0x20)
  ...

Looking at commit 7b24e798 ("pcmcia: split up central event handler"),
the following change was made to cs.c:

                return 0;
        }
 #endif
-
-       send_event(skt, CS_EVENT_PM_RESUME, CS_EVENT_PRI_LOW);
+       if (!(skt->state & SOCKET_CARDBUS) && (skt->callback))
+               skt->callback->early_resume(skt);
        return 0;
 }

And the corresponding change in ds.c is from:

-static int ds_event(struct pcmcia_socket *skt, event_t event, int priority)
-{
-       struct pcmcia_socket *s = pcmcia_get_socket(skt);
...
-       switch (event) {
...
-       case CS_EVENT_PM_RESUME:
-               if (verify_cis_cache(skt) != 0) {
-                       dev_dbg(&skt->dev, "cis mismatch - different card\n");
-                       /* first, remove the card */
-                       ds_event(skt, CS_EVENT_CARD_REMOVAL, CS_EVENT_PRI_HIGH);
-                       mutex_lock(&s->ops_mutex);
-                       destroy_cis_cache(skt);
-                       kfree(skt->fake_cis);
-                       skt->fake_cis = NULL;
-                       s->functions = 0;
-                       mutex_unlock(&s->ops_mutex);
-                       /* now, add the new card */
-                       ds_event(skt, CS_EVENT_CARD_INSERTION,
-                                CS_EVENT_PRI_LOW);
-               }
-               break;
...
-    }

-    pcmcia_put_socket(s);

-    return 0;
-} /* ds_event */

to:

+static int pcmcia_bus_early_resume(struct pcmcia_socket *skt)
+{
+       if (!verify_cis_cache(skt)) {
+               pcmcia_put_socket(skt);
+               return 0;
+       }

+       dev_dbg(&skt->dev, "cis mismatch - different card\n");

+       /* first, remove the card */
+       pcmcia_bus_remove(skt);
+       mutex_lock(&skt->ops_mutex);
+       destroy_cis_cache(skt);
+       kfree(skt->fake_cis);
+       skt->fake_cis = NULL;
+       skt->functions = 0;
+       mutex_unlock(&skt->ops_mutex);

+       /* now, add the new card */
+       pcmcia_bus_add(skt);
+       return 0;
+}

As can be seen, the original function called pcmcia_get_socket() and
pcmcia_put_socket() around the guts, whereas the replacement code
calls pcmcia_put_socket() only in one path.  This creates an imbalance
in the refcounting.

Testing with pcmcia_put_socket() put removed shows that the bug is gone:

  dpm_suspend: c1a10998 [pcmcia_socket0] 5
  dpm_suspend_noirq: c1a10998 [pcmcia_socket0] 5
  dpm_resume_noirq: c1a10998 [pcmcia_socket0] 5
  dpm_resume: c1a10998 [pcmcia_socket0] 5
  dpm_complete: c1a10998 [pcmcia_socket0] 5
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In current code, pltfm->als_vmin is set to LM3530_ALS_WINDOW_mV and
pltfm->als_vmax is 0.  This does not make sense.  I think what we want
here is setting pltfm->als_vmax to LM3530_ALS_WINDOW_mV.

Both als_vmin and als_vmax local variables will be set to
pltfm->als_vmin and pltfm->als_vmax by a few lines latter.  Thus also
remove a redundant assignment for als_vmin and als_vmax in this patch.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

New pohmelfs is coming, and it is time to remove deadly old design
https://lkml.org/lkml/2012/2/8/293Signed-off-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit a0417fa3 ("net: Make qdisc_skb_cb upper size bound
explicit.") made it possible for a netdev driver to use skb->cb
between its header_ops.create method and its .ndo_start_xmit
method.  Use this in ipoib_hard_header() to stash away the LL address
(GID + QPN), instead of the "ipoib_pseudoheader" hack.  This allows
IPoIB to stop lying about its hard_header_len, which will let us fix
the L2 check for GRO.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to the sysdev conversion to struct device, the cpu objects get
reused when adding a cpu after offlining it, which causes a big warning
that the kobject portion is not properly initialized.

So clear out the object before we register it again, so all is quiet.
Reported-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Those lines have two copies.

Not sure how it could happen, looks like git problem.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 9bef3d41

	"serial: group all the 8250 related code together"

inadvertently swept up the m32r driver in the move, because
it had comments mentioning 8250 registers within it.  However
these are only there by nature of the driver being based off
the 8250 source code -- the hardware itself does not actually
have any relation to the original 8250 style UARTs.
Reported-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes UML build:

    CC      drivers/staging/android/ram_console.o
  drivers/staging/android/ram_console.c: In function
  'ram_console_driver_probe':
  drivers/staging/android/ram_console.c:358:2: error: implicit declaration
  of function 'ioremap' [-Werror=implicit-function-declaration]
  cc1: some warnings being treated as errors
  make[3]: *** [drivers/staging/android/ram_console.o] Error 1
Signed-off-by: NAnton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In https://bugs.archlinux.org/task/27996, failure of driver r8712u is
reported, with a timeout during module loading due to synchronous loading
of the firmware. The code now uses request_firmware_nowait().
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The stub_probe function can be called as soon as the stub_driver is
registered. This can lead to the busid_table_lock being used before it
is initialized. Moved calling the init_busid_table function (which
initalizes this spinlock) to be called earlier in the init function to
prevent this from happening.
Signed-off-by: NBart Westgeest <bart@elbrys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When this driver was upgraded to the vendor 20100831 version in
commit 93c55dda et al,, one listhead initialization was missed.
This broke complete operation of the driver whenever AP mode was
enabled.

This patch fixes https://bugs.archlinux.org/task/27996.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.stable.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This structure is still used after it has been freed, since it
is being allocated in probe, calls to free it have been moved to
module's remove routine.

This should fix the follwoing messages when attempting to remove the
module:
 drv_get_first_dev_extension: Failed to retrieve the object handle
 drv_get_first_dev_extension: Failed to retrieve the object handle
 drv_destroy: Failed to store DRV object
 mgr_destroy: Failed to store MGR object
Signed-off-by: NOmar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There are two members of pr_ctxt allocated during bridge_open that
are never freed resulting in memory leaks, these are stream_id and
node_id, they are now freed on release of the handle (bridge_release)
right before freeing pr_ctxt.

Error path for bridge_open was also fixed since the same variables
could result in memory leaking due to missing handling of failure
scenarios. While at it, the indentation changes were introduced to
avoid interleaved goto statements inside big if blocks.
Signed-off-by: NOmar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If a process forked and the child process was killed by the
lowmemorykiller, the lowmemory killer would be disabled until
the parent process reaped the child or it died itself.
Signed-off-by: NArve Hjønnevåg <arve@android.com>
Signed-off-by: NAnton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In a multithreaded workload, the zv_curr_dist_counts
and zv_cumul_dist_counts statistics are being corrupted
because the increments and decrements in zv_create
and zv_free are not atomic.

This patch converts these statistics and their corresponding
increments/decrements/reads to atomic operations.
Signed-off-by: NSeth Jennings <sjenning@linux.vnet.ibm.com>
Acked-by: NDan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add MODULE_LICENSE() for this source module to fix build warning:

WARNING: modpost: missing MODULE_LICENSE() in drivers/staging/media/go7007/go7007-usb.o
see include/linux/module.h for more information
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: Ross Cohen <rcohen@snurgle.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>