- 16 10月, 2006 23 次提交
-
-
由 Paul Mackerras 提交于
This implements a lazy strategy for disabling interrupts. This means that local_irq_disable() et al. just clear the 'interrupts are enabled' flag in the paca. If an interrupt comes along, the interrupt entry code notices that interrupts are supposed to be disabled, and clears the EE bit in SRR1, clears the 'interrupts are hard-enabled' flag in the paca, and returns. This means that interrupts only actually get disabled in the processor when an interrupt comes along. When interrupts are enabled by local_irq_enable() et al., the code sets the interrupts-enabled flag in the paca, and then checks whether interrupts got hard-disabled. If so, it also sets the EE bit in the MSR to hard-enable the interrupts. This has the potential to improve performance, and also makes it easier to make a kernel that can boot on iSeries and on other 64-bit machines, since this lazy-disable strategy is very similar to the soft-disable strategy that iSeries already uses. This version renames paca->proc_enabled to paca->soft_enabled, and changes a couple of soft-disables in the kexec code to hard-disables, which should fix the crash that Michael Ellerman saw. This doesn't yet use a reserved CR field for the soft_enabled and hard_enabled flags. This applies on top of Stephen Rothwell's patches to make it possible to build a combined iSeries/other kernel. Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Anton Blanchard 提交于
During boot we bring up all memory and cpu nodes. Normally a PCI device will be in one of these online nodes, however in some weird setups it may not. We have only seen this in the lab but we may as well check for the case and fallback to -1 (all nodes). Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Anton Blanchard 提交于
Instead of just checking that an address is in the right range, use the provided __kernel_text_address() helper which covers both the kernel and module text sections. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Anton Blanchard 提交于
Change ->num_pmcs to match the number of PMCs in POWER6. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Anton Blanchard 提交于
At the moment we rely on a cpu feature bit or a firmware property to detect altivec. If we dont have either of these and the cpu does in fact support altivec we can cause a panic from userspace. It seems safer to always send a signal if we manage to get an 0xf20 exception from userspace. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Randy Vinson 提交于
When update_bridge_base() updates the IO window on a PCI-to-PCI bridge, it fails to zero the upper 16 bits of the base and limit registers if the window size is less than 64K. This fixes it. Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Li Yang 提交于
Add missing entry in Makefile for MPC832x MDS support. It also change white space to tab in MPC8360 entry. Signed-off-by: NLi Yang <leoli@freescale.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Li Yang 提交于
MPC8360EMDS PB support is broken as some code was missing in last submission. This patch adds missing code and makes MPC8360EMDS PB support working. Signed-off-by: NLi Yang <leoli@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
In the timer_interrupt we were not calling set_irq_regs() and if we are profiling we will end up calling get_irq_regs(). This causes bad things to happen. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Eric Sesterhenn 提交于
A find -iname \*.[ch] | xargs grep "> ARRAY_SIZE(" revealed several incorrect usages of ARRAY_SIZE in the mpc drivers. The last element in the array is always ARRAY_SIZE()-1, this patch modifies the bounds checks accordingly. Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de> Cc: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Timur Tabi 提交于
The default configuration file for the MPC8349E-mITX reference board, mpc834x_itx_defconfig, did not include support for DOS partition table types. This support is necessary because the hard drive that comes with the ITX is formatted with this partition table type. Without this config option, no partitions on the drive can be mounted. Signed-off-by: NTimur Tabi <timur@freescale.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Noguchi, Masato 提交于
This fixes a memory leak introduced by "spufs: add support for read/write oncntl", which was missing a call to simple_attr_close. Signed-off-by: NMasato Noguchi <Masato.Noguchi@jp.sony.com> Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
The SPU code will crash if CONFIG_NUMA is not set and SPUs are found on a non-0 node. This workaround will ignore those SPEs and just print an message in the kernel log. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Ulrich Drepper 提交于
I need this patch to get a UML kernel to compile. This is with the kernel headers in FC6 which are automatically generated from the kernel tree. Some headers are missing but those files don't need them. At least it appears so since the resuling kernel works fine. Tested on x86-64. Signed-off-by: NUlrich Drepper <drepper@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Linus Torvalds 提交于
.. and clean up the file mapping code while at it. No point in having a "if (file)" repeated twice, and generally doing similar checks in two different sections of the same code Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Petr Vandrovec 提交于
It is silly to use non-static variable for writting zeroes to the file. And more seriously, foffset in core dump file dump function was incremented too much, so some parts of core dump were shifted by size of few phdrs and notes down, so although gdb was able to load that file, it did not make lot of sense - in my test case data pages were shifted down by about 900 bytes. Signed-off-by: NPetr Vandrovec <petr@vandrovec.name> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6由 Linus Torvalds 提交于
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (28 commits) ACPI: check battery status on resume for un/plug events during sleep ACPICA: Fix incorrect handling of PCI Express Root Bridge _HID ACPI: asus_acpi: don't printk on writing garbage to proc files ACPI: asus_acpi: fix proc files parsing ACPI: SCI interrupt source override ACPI: fix printk format warnings ACPI: fix section for CPU init functions ACPI: update comments in motherboard.c ACPI: acpi_pci_link_set() can allocate with either GFP_ATOMIC or GFP_KERNEL ACPI: fix potential OOPS in power driver with CONFIG_ACPI_DEBUG ACPI: ibm_acpi: delete obsolete documentation ACPI: created a dedicated workqueue for notify() execution ACPI: Remove deferred execution from global lock acquire wakeup path MSI S270 Laptop support: backlight, wlan, bluetooth states ACPI: EC: export ec_transaction() for msi-laptop driver ACPI: EC: Simplify acpi_hw_low_level*() with inb()/outb(). ACPI: EC: Unify poll and interrupt gpe handlers ACPI: EC: Unify poll and interrupt mode transaction functions ACPI: EC: Remove unused variables and duplicated code ACPI: EC: Remove unnecessary delay added by previous transation patch. ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb由 Linus Torvalds 提交于
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: V4L/DVB (4750): AGC command1/2 is board specific V4L/DVB (4748): Fixed oops for Nova-T USB2 V4L/DVB (4746): HM12 is YUV 4:2:0, not YUV 4:1:1 V4L/DVB (4744): The Samsung TCPN2121P30A does not have a tda9887 V4L/DVB (4743): Fix oops in VIDIOC_G_PARM V4L/DVB (4742): Drivers/media/video: handle sysfs errors V4L/DVB (4741): {ov511,stv680}: handle sysfs errors V4L/DVB (4740): Fixed an if-block to avoid floating with debug-messages V4L/DVB (4739): SECAM support for saa7113 into saa7115 V4L/DVB (4738): Bt8xx/dvb-bt8xx.c: check kmalloc() return value. V4L/DVB (4734): Tda826x: fix frontend selection for dvb_attach V4L/DVB (4733): Tda10086: fix frontend selection for dvb_attach V4L/DVB (4732): Fix spelling error in Kconfig help text for DVB_CORE_ATTACH V4L/DVB (4731a): Kconfig: restore pvrusb2 menu items V4L/DVB (4729): Fix VIDIOC_G_FMT for NTSC in cx25840. V4L/DVB (4727): Support status readout for saa713x based FM radio V4L/DVB (4725): Fix vivi compile on parisc V4L/DVB (4692): Add WinTV-HVR3000 DVB-T support
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
* missing cpu_to_le64() for ChangeTime (introduced by [CIFS] Legacy time handling for Win9x and OS/2 part 1) * missing le16_to_cpu() for DialectIndex (introduced by [CIFS] Do not send newer QFSInfo to legacy servers which can not support it) Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 14 10月, 2006 17 次提交
-
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Jiri Kosina 提交于
Add ->resume method to the ACPI battery handler to check if the battery state has changed during sleep. If yes, update the ACPI internal data structures for benefit of /proc/acpi/battery/. Signed-off-by: NJiri Kosina <jikos@jikos.cz> Cc: Stefan Seyfried <seife@suse.de> Acked-by: NPavel Machek <pavel@ucw.cz> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Eiichiro Oiwa 提交于
I could not get correct PCI Express bus number from the structure of acpi_object_extra. I always get zero as bus number regardless of bus location. I found that there is incorrect comparison with _HID (PNP0A08) in acpi/events/evrgnini.c and PCI Express _BBN method always fail. Therefore, we always get zero as PCI Express bus number. http://bugzilla.kernel.org/show_bug.cgi?id=7145Signed-off-by: NBob Moore <robert.moore@intel.com> Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com> Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Alexey Dobriyan 提交于
This reporting is useless (we errno anyway). Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Darren Jenkins 提交于
ICC complains about a "Pointless comparsion of unsigned interger with zero" @ line 760 & 808 of asus_acpi.c parse_arg() mentioned below returns -E but it's copied into unsigned variable... Signed-off-by: NDarren Jenkins <darrenrjenkins@gmail.com> Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Kimball Murray 提交于
The Linux group at Stratus Technologies has come across an issue with SCI routing under ACPI. We were bitten by this when we made an x86_64 platform whose BIOS provides an Interrupt Source Override for the SCI itself. Apparently the override has no effect for the System Control Interrupt, and this appears to be because of the way the SCI is setup in the ACPI code. It does not handle the case where busirq != gsi. The code that sets up the SCI routing assumes that bus irq == global irq. So there is simply no provision for telling it otherwise. The attached patch provides this mechanism. This patch provided by David Bulkow, was tested on an i386 platform, which does not use the SCI override, and also on an x86_64 platform which does use an override. Signed-off-by: NDavid Bulkow <david.bulkow@stratus.com> Cc: Andi Kleen <ak@muc.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Randy Dunlap 提交于
Fix printk format warnings in drivers/acpi: drivers/acpi/tables/tbget.c:326: warning: format '%X' expects type 'unsigned int', but argument 5 has type 'long unsigned int' drivers/acpi/tables/tbrsdt.c:189: warning: format '%X' expects type 'unsigned int', but argument 5 has type 'long unsigned int' Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Pierre Ossman 提交于
The ACPI processor init functions should be marked as __cpuinit as they use structures marked with __cpuinitdata. Signed-off-by: NPierre Ossman <drzeus@drzeus.cx> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Len Brown 提交于
Signed-off-by: NLen Brown <len.brown@intel.com>
-