Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Expose firmware limit for the max_scan_ie_len;
also do actually set IE's for the probe request

max_scan_ie_len used to be 0, this blocks scan requests with non-zero IE's
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

re-use of wmi_ready for both FW ready event and for wmi_call was causing
false "FW not ready" indication in case wmi_call() was invoked while reset
took place.
add wmi_call completion variable instead of re-using wmi_ready.
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

HW supports upto 2304 packet size on the air.
HW is responsible for adding (Tx) or removing (Rx) the following headers:
802.11 hdr: 26B
SNAP: 8B
CRC: 4B
Security (optional): 24B
HW adds max 62B to the payload passed from driver. It means driver can use
max packet size of 2304-62 = 2242B
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This allows updating IEs (e.g. from hostapd) when AP is already started
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver is sending connect request IEs to FW only for secure connection and
ignores them for non-secure connection.
This is fixed by always sending the IEs to FW upon connect request
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While handling Rx packet, BACK event arrives and frees tid_ampdu_rx array.
This causes kernel panic while accessing already freed spinlock

The fix is to remove tid_ampdu_rx[]'s spinlock and instead use single
sta's spinlock to guard the whole tid_ampdu_rx array.
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When WMI event received when driver not ready to accept it, the printed error
message is misleading and hints that HW is stuck. Modify the error message
to make it clearer
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This race condition was causing double free of tid_ampdu_rx structures
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When CONFIG_DYNAMIC_DEBUG is not defined, print_hex_dump_debug
is mapped directly to print_hex_dump which might cause
printout to exist all the time
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver disabled PCI master before making sure HW is idle.
This caused memory corruption in case HW access system memory after
PCI master got disabled.
The fix is to change uninit sequence. Make sure FW/HW is idle before
disabling PCI
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After setting interrupt handler, driver enabled interrupts.
This caused stale (old) HW interrupts to fire before driver is
fully initialized.
The fix is to enable interrupts only when driver is fully initialized
and after FW/HW reset (to prevent any stale interrupts)
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

added misc printouts in some init/uninit functions for better traceability
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

New module (wil_platform) for handling platform specific tasks
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

- parentheses, indentation, typos
- seq_puts() instead of seq_printf() with single argument
- sizeof(var) vs. sizeof(type)
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Log worker thread start/stop; as well as every handler invocation
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

when connecting, print some info about BSS
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware download implemented but is still experimental feature;
flag controlling it added, no_fw_load. It is true by default,
use no_fw_load=N to activate feature.

Reset flows also got some adjustment for the fw download to work
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I misunderstood original Broadcom comment and used wrong values.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 0-DAY kernel build testing backend reports the following warning:
drivers/net/wireless/rtlwifi/btcoexist/halbtcoutsrc.c:516 halbtc_bitmask_write_1byte()
warn: always true condition '(bit_mask != 4294967295) => (0-255 != u32max)'

This problem was introduced in commit ed364abf,
and arises because the caller of halbtc_bitmask_write_1byte() is using a
u8 rather than a u32 for the data.
Reported-by: NKbuild test robot <kbuild-all@01.org>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Kbuild test robot <kbuild-all@01.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also use b43_radio_wait_value to simplify the code and usleep_range when
needed.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Radio should be prepared only before initialization. We need this to be
able to call b43_radio_2059_init conditionally (in the future).
This also documents RF control register a bit.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHans Wennborg <hans@hanshq.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHans Wennborg <hans@hanshq.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This core is used on BCM4708 to configure the PCIe and USB3 PHYs and it
contains the addresses to the Device Management unit. This will be used
by the PCIe driver first.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Each core could have more than one alternative address. There are cores
with 8 alternative addresses for different functions. The PHY control
in the Chip common B core is done through the 2. alternative address
and not the first one.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
CC: linux-usb@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Scanning is curently broken when two channel contexts
are active. For example in a P2P-GO/STA setup, the
offchannel timer allows HZ / 10 to elapse before initiating
a switch to the next scan channel from the current operating
channel, which in this case would be the P2P-GO context.

But, the channel context timer might decide to switch
to the STA context when an SWBA comes early and a beacon
is sent out. Since pending offchannel requests are processed
in EVENT_BEACON_PREPARE, this causes inconsistent scanning.

Fix this by making sure that a context switch happens
before processing the pending offchannel request. This
also makes sure that active channel contexts will always
have higher priority than offchannel operations and the
scan sequence looks like this:

p2p-go, sta, p2p-go, offchannel, p2p-go, sta, p2p-go, offchannel,.....

The oper-channel is p2p-go, so the STA context has to
switch to p2p-go again before switching offchannel.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When multiple channel contexts are active, an offchannel
request will not be handled immediately, but will be
queued to be handled later. But, currently, the channel definition
is not copied to the local offchannel state. This
breaks operation like scanning when MCC is active.

Fix this by storing the offchannel parameters properly.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reduces code duplication.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, the interface count is maintained globally,
but this causes problems in RX filter calculation.
Make the interface count a per-channel-context variable
to fix this.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Maintain the RX filter on a per-channel-context
basis and not globally. Not doing so was resulting
in incorrect filter calculation.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ATH9K_RX_FILTER_COMP_BAR is used to receive BAR
completion frames and is set if the current channel
is HT. When channel contexts are enabled, instead of using
the mac80211 helpers, check if the current channel
definition is HT.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since ath_startrecv() doesn't return an error value,
cleanup the callsites.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If multiple channel contexts are active, then the opmode
can be different in each context. Since the RX filter is
calculated in ath_startrecv() before switching to the
new opmode, the wrong filters are chosen.

Fix this by calling ath9k_calculate_summary_state() before
the RX module is started.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since CTWindow can be used for improving discoverability,
fill this field in the NoA Attribute properly.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, different units are used for handling
sc->offchannel.duration. In scan mode, it contains jiffies and in RoC
mode, milliseconds is used. This causes confusion since in
ath_chanctx_switch(), TU_TO_USEC is used to determine the offchannel
duration, resulting in incorrect values. Fix this by using jiffies in
both modes.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The start time field in the NoA attribute needs to be
updated based on the TSF timer when an absence notification
is sent by the P2P GO. When two channel contexts are active,
continuous, cyclic NoA is announced by setting the count value to 255,
but the start time is updated only once, for one beacon and
the same value is sent in all subsequent beacons, even
though the timestamp keeps moving.

Fix this by removing the check for 'periodic_noa_duration'
and assign the interface's start_time/duration values directly
when there is more than one active context.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>