- 23 9月, 2014 5 次提交
-
-
由 Michal Kazior 提交于
Simplify the code by deduplicating structure definitions and code. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
The structure is being set up in 2 places. Deduplicate the code by creating a helper. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
This command is not used anymore and most firmware revisions do not seem to handle it well. Channel switching is done via vdev restarting. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Firmware reports the number of RF chains so use that for initialization of supp_{tx,rx}_chainmask instead of using a macro for 3x3 chips. This should make tx/rx chainmask reports correct for chips other than 3x3. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Some firmware revisions don't wait for beacon tx completion before sending another SWBA event. This could lead to hardware using old (freed) beacon data in some cases, e.g. tx credit starvation combined with missed TBTT. This is very very rare. On non-IOMMU-enabled hosts this could be a possible security issue because hw could beacon some random data on the air. On IOMMU-enabled hosts DMAR faults would occur in most cases and target device would crash. Since there are no beacon tx completions (implicit nor explicit) propagated to host the only workaround for this is to allocate a DMA-coherent buffer for a lifetime of a vif and use it for all beacon tx commands. Worst case for this approach is some beacons may become corrupted, e.g. garbled IEs or out-of-date TIM bitmap. Keep the original beacon-related code as-is in case future firmware revisions solve this problem so that the old path can be easily re-enabled with a fw_feature flag. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
- 18 9月, 2014 10 次提交
-
-
由 Kalle Valo 提交于
As suggeested by checkpatch: WARNING: Prefer ether_addr_copy() over memcpy() if the Ethernet addresses are __aligned(2) In wmi.c I had to change due to sparse warnings copying of struct wmi_mac_addr from form &cmd->peer_macaddr.addr to cmd->peer_macaddr.addr. In ath10k_wmi_set_ap_ps_param() I also added the missing ".addr" to the copy command. Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Kalle Valo 提交于
Makes it more readable and fixes checkpatch warnings: drivers/net/wireless/ath/ath10k/debug.c:593: WARNING: quoted string split across lines drivers/net/wireless/ath/ath10k/debug.c:594: WARNING: quoted string split across lines drivers/net/wireless/ath/ath10k/debug.c:595: WARNING: quoted string split across lines drivers/net/wireless/ath/ath10k/debug.c:596: WARNING: quoted string split across lines drivers/net/wireless/ath/ath10k/debug.c:597: WARNING: quoted string split across lines drivers/net/wireless/ath/ath10k/debug.c:599: WARNING: quoted string split across lines drivers/net/wireless/ath/ath10k/debug.c:600: WARNING: quoted string split across lines Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Kalle Valo 提交于
Fixes checkpatch warnings: ath10k/htc.c:49: WARNING: Possible unnecessary 'out of memory' message ath10k/htc.c:810: WARNING: Possible unnecessary 'out of memory' message ath10k/htt.h:1034: CHECK: Please use a blank line after function/struct/union/enum declarations ath10k/htt_rx.c:135: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr ath10k/htt_rx.c:173: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr ath10k/pci.c:633: WARNING: macros should not use a trailing semicolon ath10k/wmi.c:3594: WARNING: quoted string split across lines Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Kalle Valo 提交于
Fixes checkpatch warnings: WARNING: else is not generally useful after a break or return Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Kalle Valo 提交于
Fixes a checkpatch warning: WARNING: void function return statements are not generally useful Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Kalle Valo 提交于
Fixes checkpatch warnings: CHECK: No space is necessary after a cast Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Kalle Valo 提交于
Fixes checkpatch warnings: WARNING: Missing a blank line after declarations Please note that some of the cases I fixed by moving the variable declarations to the beginning of the function, which is the preferred style in ath10k. Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Kalle Valo 提交于
Fixes checkpatch warnings: CHECK: Please don't use multiple blank lines Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Kalle Valo 提交于
CHECK: Alignment should match open parenthesis Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Kalle Valo 提交于
Fixes checkpatch warning: ath10k/htt_rx.c:519: CHECK: Alignment should match open parenthesis Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
- 12 9月, 2014 4 次提交
-
-
由 Michal Kazior 提交于
The function may return an -ENODEV if debugfs is disabled in kernel. This should originally be guarded by ath10k's Kconfig but it still makes sense to check for the non-NULL errno return value. Reported-by: NMatteo Croce <matteo@openwrt.org> Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Ben Greear 提交于
10.1 firmware does not have an official way to cause assert on purpose, but it can be done with carefully crafted WMI command. This is a different kind of crash from the 'hard' crash, which is a bad memory dereference. Different crashes decode in different manners, so this will help the crash-report testing as well as offer better ways to test firmware failure and recovery. kvalo: move the wmi command creation to debug.c, modify the info print Signed-off-by: NBen Greear <greearb@candelatech.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Kalle Valo 提交于
Add testmode interface for starting and using UTF firmware which is used to run factory tests. This is implemented by adding new state ATH10K_STATE_UTF and user space can enable this state with ATH10K_TM_CMD_UTF_START command. To go back to normal mode user space can send ATH10K_TM_CMD_UTF_STOP. Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Kalle Valo 提交于
We need this function to send wmi packets from testmode.c. Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
- 10 9月, 2014 3 次提交
-
-
由 Matteo Croce 提交于
ATH10K_DEBUGFS must depend on DEBUG_FS, otherwise ath10k will generate an invalid pointer on module load. Signed-off-by: NMatteo Croce <matteo@openwrt.org> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
On 32bit systems the bitmap was too small and it was overwritten partially by the stat completion structure. This was visible with 10.2 firmware only due to it using a few of the last service ids. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
The fw_crash_data was allocated too late. Upon early firmware crash, before registering to mac80211, it was possible to crash the whole system: ath10k_pci 0000:00:05.0: device has crashed during init BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffffa0058005>] ath10k_debug_get_new_fw_crash_data+0x15/0x30 [ath10k_core] PGD 0 Oops: 0002 [#1] SMP Modules linked in: ath10k_pci(O) ath10k_core(O) ath [last unloaded: ath] CPU: 3 PID: 29 Comm: kworker/u8:1 Tainted: G O 3.17.0-rc2-wl-ath+ #447 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core] task: ffff88001eb01ad0 ti: ffff88001eb60000 task.ti: ffff88001eb60000 RIP: 0010:[<ffffffffa0058005>] [<ffffffffa0058005>] ath10k_debug_get_new_fw_crash_data+0x15/0x30 [ath10k_core] RSP: 0018:ffff88001eb63ce8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffffc90001a09030 RDI: 0000000000000001 RBP: ffff88001eb63cf0 R08: 0000000000000000 R09: ffff8800000bb200 R10: 00000000000001e2 R11: ffff88001eb638de R12: ffff88001d7459a0 R13: ffff88001d746ab0 R14: 00000000fffe14d4 R15: ffff88001d747c60 FS: 0000000000000000(0000) GS:ffff88001fd80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000000 CR3: 000000001df34000 CR4: 00000000000006e0 Stack: ffff88001d7459a0 ffff88001eb63d58 ffffffffa0083bbe ffff880000000010 ffff88001eb63d68 ffff88001eb63d18 0000000000000002 0000000000059010 ffffffffa0086fef 00000000deadbeef ffff88001d747a28 ffff88001d7459a0 Call Trace: [<ffffffffa0083bbe>] ath10k_pci_fw_crashed_dump+0x2e/0xd0 [ath10k_pci] [<ffffffffa0085410>] __ath10k_pci_hif_power_up+0x5f0/0x700 [ath10k_pci] [<ffffffffa0085550>] ath10k_pci_hif_power_up+0x30/0xe0 [ath10k_pci] [<ffffffffa005bc7b>] ath10k_core_register_work+0x2b/0x520 [ath10k_core] [<ffffffff810689cc>] process_one_work+0x18c/0x3f0 [<ffffffff81069011>] worker_thread+0x121/0x4a0 [<ffffffff81068ef0>] ? rescuer_thread+0x2c0/0x2c0 [<ffffffff8106daf2>] kthread+0xd2/0xf0 [<ffffffff8106da20>] ? kthread_create_on_node+0x170/0x170 [<ffffffff81857cfc>] ret_from_fork+0x7c/0xb0 [<ffffffff8106da20>] ? kthread_create_on_node+0x170/0x170 Code: 8b 40 38 48 c7 80 00 01 00 00 00 00 00 00 5b 5d c3 0f 1f 44 00 00 0f 1f 44 00 00 55 48 89 e5 53 48 8b 9f 90 1d 00 00 48 8d 7b 01 <c6> 03 01 e8 e3 ec 2b e1 48 8d 7b 18 e8 6a 4f 05 e1 48 89 d8 5b RIP [<ffffffffa0058005>] ath10k_debug_get_new_fw_crash_data+0x15/0x30 [ath10k_core] RSP <ffff88001eb63ce8> CR2: 0000000000000000 ---[ end trace 5d0ed15b050bcc1f ]--- Kernel panic - not syncing: Fatal exception in interrupt Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff) ---[ end Kernel panic - not syncing: Fatal exception in interrupt To prevent that split debug functions and allocate fw_crash_data earlier. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
- 02 9月, 2014 8 次提交
-
-
由 Michal Kazior 提交于
Nothing important was being overwritten so it didn't yield any bugs yet. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
This makes it easier to log and debug via tracing with more than 1 ath10k device on a system. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Remove the ugly _access functions. Being explicit is a good thing. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
This prevents some fw revisions from crashing in many cases when user is trying to run a promiscuous station interface (e.g. sniffing, 4addr bridge). Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Fix some cases where monitor start failure left the driver in a confused state. This also makes the monitor code simpler. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Commit 5c771e74 introduced a regression. On some systems spurious interrupts could schedule a tasklet while tearing down leading to, e.g.: BUG: unable to handle kernel paging request at fe589030 IP: [<c1316fb0>] ioread32+0x30/0x40 ... Call Trace: [<fe576c1b>] ath10k_pci_tasklet+0x1b/0x60 [ath10k_pci] [<c1053fbe>] tasklet_action+0x9e/0xb0 [<c10534f1>] __do_softirq+0xf1/0x3f0 [<c1053400>] ? ftrace_raw_event_irq_handler_entry+0xa0/0xa0 [<c1004999>] do_softirq_own_stack+0x29/0x40 <IRQ> [<c1053a76>] irq_exit+0x86/0xb0 ... [<c132d522>] do_pci_disable_device+0x52/0x60 [<c132d57f>] pci_disable_device+0x4f/0xb0 [<c132a961>] ? __pci_set_master+0x51/0x80 [<fe5740b3>] ath10k_pci_release+0x33/0x40 [ath10k_pci] [<fe575d4b>] ath10k_pci_remove+0x7b/0x90 [ath10k_pci] Reported-by: NKalle Valo <kvalo@qca.qualcomm.com> Tested-by: NKalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
If a station was reassociated, i.e. due to change of supported rates update via sta_rc_update() the num_legacy_stations would be (incorrectly) bumped up leading to unbalanced usage of the var. This in turn could lock rtscts protection up as enabled. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Recent changes done to start/restart sequences broke hw recovery in some hw configurations. The pci transport was stopped twice however due to a workaround in the pci disabling code the disable/enable for first msi interrupt was not balanced. This ended up with irqs not being properly re-enabled and the following print out during recovery: ath10k: failed to receive control response completion, polling.. ath10k: Service connect timeout: -110 ath10k: Could not init core: -110 Legacy interrupt mode was unaffected while msi ranged mode would be partially crippled (it would miss fw indication interrupts but otherwise it worked fine). This fixes completely broken fw recovery for a single msi interrupt mode and fixes subsequent fw crash reports for msi range interrupt mode. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
- 29 8月, 2014 10 次提交
-
-
由 Andreea-Cristina Bernat 提交于
According to RCU_INIT_POINTER()'s block comment 3.a, it can be used if "3. The referenced data structure has already been exposed to readers either at compile time or via rcu_assign_pointer() -and- a. You have not made -any- reader-visible changes to this structure since then". This case fulfills the conditions above because between the rcu_dereference() call (cvif = rcu_dereference(ar->beacon_iter);) and the rcu_assign_pointer() call there is no update of the "cvif" variable. Therefore, this patch makes the replacement. The following Coccinelle semantic patch was used: @@ identifier v; @@ v = rcu_dereference(...); ... when != rcu_dereference(...); when != v = ...; when != (<+...v...+>)++; when != \(memcpy\|memset\)(...); ( - rcu_assign_pointer + RCU_INIT_POINTER (..., v); | if(...) { ... when != v = ...; - rcu_assign_pointer + RCU_INIT_POINTER (..., v); ... when any } ) Because there are cases where between a “rcu_dereference()” call and a “rcu_assign_pointer()” call might be updates of the value that interests us, the Coccinelle semantic patch ignores them and replaces with "RCU_INIT_POINTER()" only when the update is not happening. Signed-off-by: NAndreea-Cristina Bernat <bernat.ada@gmail.com> Acked-by: NChristian Lamparter <chunkeey@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Setup the channel context correctly. Not doing this was causing beacon loss in a P2P-GO/STA concurrent setup. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Canek Peláez Valdés 提交于
Signed-off-by: NCanek Peláez Valdés <canek@ciencias.unam.mx> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
If a new context is being added in addition to the current one, then send the ASSIGN event to abort a running scan since the addition of a context is usually followed by VIF assignment and further operations. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
There is no reason why managed/p2p interfaces have to be limited to one. IBSS is the only type that needs a restriction. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
This will be useful in handling addition/change of new channel contexts. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Move it inside a CONFIG_ATH9K_CHANNEL_CONTEXT ifdef since it is not needed otherwise. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-