All spi based drivers have an instance of struct spi_device
as spi. This patch renames spi_device to spi to synchronize
with all the drivers.
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jesper Dangaard Brouer says:

====================
The following series introduce some pktgen changes

Patch01:
 Cleanup my own work when I introduced NO_TIMESTAMP.

Patch02:
 Took over patch from Alexei, and addressed my own concerns, as Alexie
 is too busy with other work, and this will provide an easy tool for
 measuring ingress path performance, which is a hot topic ATM.

 Changes were primarily user interface related.  Introduced a separate
 "xmit_mode" setting, instead of stealing one of the dev flags like
 Alexei did.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce xmit_mode 'netif_receive' for pktgen which generates the
packets using familiar pktgen commands, but feeds them into
netif_receive_skb() instead of ndo_start_xmit().

Default mode is called 'start_xmit'.

It is designed to test netif_receive_skb and ingress qdisc
performace only. Make sure to understand how it works before
using it for other rx benchmarking.

Sample script 'pktgen.sh':
\#!/bin/bash
function pgset() {
  local result

  echo $1 > $PGDEV

  result=`cat $PGDEV | fgrep "Result: OK:"`
  if [ "$result" = "" ]; then
    cat $PGDEV | fgrep Result:
  fi
}

[ -z "$1" ] && echo "Usage: $0 DEV" && exit 1
ETH=$1

PGDEV=/proc/net/pktgen/kpktgend_0
pgset "rem_device_all"
pgset "add_device $ETH"

PGDEV=/proc/net/pktgen/$ETH
pgset "xmit_mode netif_receive"
pgset "pkt_size 60"
pgset "dst 198.18.0.1"
pgset "dst_mac 90:e2:ba:ff:ff:ff"
pgset "count 10000000"
pgset "burst 32"

PGDEV=/proc/net/pktgen/pgctrl
echo "Running... ctrl^C to stop"
pgset "start"
echo "Done"
cat /proc/net/pktgen/$ETH

Usage:
$ sudo ./pktgen.sh eth2
...
Result: OK: 232376(c232372+d3) usec, 10000000 (60byte,0frags)
  43033682pps 20656Mb/sec (20656167360bps) errors: 10000000

Raw netif_receive_skb speed should be ~43 million packet
per second on 3.7Ghz x86 and 'perf report' should look like:
  37.69%  kpktgend_0   [kernel.vmlinux]  [k] __netif_receive_skb_core
  25.81%  kpktgend_0   [kernel.vmlinux]  [k] kfree_skb
   7.22%  kpktgend_0   [kernel.vmlinux]  [k] ip_rcv
   5.68%  kpktgend_0   [pktgen]          [k] pktgen_thread_worker

If fib_table_lookup is seen on top, it means skb was processed
by the stack. To benchmark netif_receive_skb only make sure
that 'dst_mac' of your pktgen script is different from
receiving device mac and it will be dropped by ip_rcv
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow flag NO_TIMESTAMP to turn timestamping on again, like other flags,
with a negation of the flag like !NO_TIMESTAMP.

Also document the option flag NO_TIMESTAMP.

Fixes: afb84b62 ("pktgen: add flag NO_TIMESTAMP to disable timestamping")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nicolas Dichtel says:

====================
netns: ease netlink use with a lot of netns

This idea was informally discussed in Ottawa / netdev0.1. The goal is to
ease the use/scalability of netns, from a userland point of view.
Today, users need to open one netlink socket per family and per netns.
Thus, when the number of netns inscreases (for example 5K or more), the
number of sockets needed to manage them grows a lot.

The goal of this series is to be able to monitor netlink events, for a
specified family, for a set of netns, with only one netlink socket. For
this purpose, a netlink socket option is added: NETLINK_LISTEN_ALL_NSID.
When this option is set on a netlink socket, this socket will receive
netlink notifications from all netns that have a nsid assigned into the
netns where the socket has been opened.
The nsid is sent to userland via an anscillary data.

Here is an example with a patched iproute2. vxlan10 is created in the
current netns (netns0, nsid 0) and then moved to another netns (netns1,
nsid 1):

$ ip netns exec netns0 ip monitor all-nsid label
[nsid 0][NSID]nsid 1 (iproute2 netns name: netns1)
[nsid 0][NEIGH]??? lladdr 00:00:00:00:00:00 REACHABLE,PERMANENT
[nsid 0][LINK]5: vxlan10@NONE: <BROADCAST,MULTICAST> mtu 1450 qdisc noop state DOWN group default
    link/ether 92:33:17:e6:e7:1d brd ff:ff:ff:ff:ff:ff
[nsid 0][LINK]Deleted 5: vxlan10@NONE: <BROADCAST,MULTICAST> mtu 1450 qdisc noop state DOWN group default
    link/ether 92:33:17:e6:e7:1d brd ff:ff:ff:ff:ff:ff
[nsid 1][NSID]nsid 0 (iproute2 netns name: netns0)
[nsid 1][LINK]5: vxlan10@NONE: <BROADCAST,MULTICAST> mtu 1450 qdisc noop state DOWN group default
    link/ether 92:33:17:e6:e7:1d brd ff:ff:ff:ff:ff:ff link-netnsid 0
[nsid 1][ADDR]5: vxlan10    inet 192.168.0.249/24 brd 192.168.0.255 scope global vxlan10
       valid_lft forever preferred_lft forever
[nsid 1][ROUTE]local 192.168.0.249 dev vxlan10  table local  proto kernel  scope host  src 192.168.0.249
[nsid 1][ROUTE]ff00::/8 dev vxlan10  table local  metric 256  pref medium
[nsid 1][ROUTE]2001:123::/64 dev vxlan10  proto kernel  metric 256  pref medium
[nsid 1][LINK]5: vxlan10@NONE: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1450 qdisc noqueue state UNKNOWN group default
    link/ether 92:33:17:e6:e7:1d brd ff:ff:ff:ff:ff:ff link-netnsid 0
[nsid 1][ROUTE]broadcast 192.168.0.255 dev vxlan10  table local  proto kernel  scope link  src 192.168.0.249
[nsid 1][ROUTE]192.168.0.0/24 dev vxlan10  proto kernel  scope link  src 192.168.0.249
[nsid 1][ROUTE]broadcast 192.168.0.0 dev vxlan10  table local  proto kernel  scope link  src 192.168.0.249
[nsid 1][ROUTE]fe80::/64 dev vxlan10  proto kernel  metric 256  pref medium
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

More accurately, listen all netns that have a nsid assigned into the netns
where the netlink socket is opened.
For this purpose, a netlink socket option is added:
NETLINK_LISTEN_ALL_NSID. When this option is set on a netlink socket, this
socket will receive netlink notifications from all netns that have a nsid
assigned into the netns where the socket has been opened. The nsid is sent
to userland via an anscillary data.

With this patch, a daemon needs only one socket to listen many netns. This
is useful when the number of netns is high.

Because 0 is a valid value for a nsid, the field nsid_is_set indicates if
the field nsid is valid or not. skb->cb is initialized to 0 on skb
allocation, thus we are sure that we will never send a nsid 0 by error to
the userland.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These flags and states have the same prefix (NETLINK_) that netlink socket
options. To avoid confusion and to be able to name a flag like a socket
option, let's use an other prefix: NETLINK_[S|F]_.

Note: a comment has been fixed, it was talking about
NETLINK_RECV_NO_ENOBUFS socket option instead of NETLINK_NO_ENOBUFS.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before this patch, nsid were protected by the rtnl lock. The goal of this
patch is to be able to find a nsid without needing to hold the rtnl lock.

The next patch will introduce a netlink socket option to listen to all
netns that have a nsid assigned into the netns where the socket is opened.
Thus, it's important to call rtnl_net_notifyid() outside the spinlock, to
avoid a recursive lock (nsid are notified via rtnl). This was the main
reason of the previous patch.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no functional change with this patch. It will ease the refactoring
of the locking system that protects nsids and the support of the netlink
socket option NETLINK_LISTEN_ALL_NSID.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a following commit, a new function will be introduced to only lookup for
a nsid (no allocation if the nsid doesn't exist). To avoid confusion, the
existing function is renamed.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The goal of this commit is to prepare the rework of the locking of nsnid
protection.
After this patch, rtnl_net_notifyid() will not call anymore __peernet2id(),
ie no idr_* operation into this function.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All callers of this function expect a nsid, not an error.
Thus, returns NETNSA_NSID_NOT_ASSIGNED in case of error so that callers
don't have to convert the error to NETNSA_NSID_NOT_ASSIGNED.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-4.2-20150506' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2015-05-06

this is a pull request of a seven patches for net-next/master.

Andreas Gröger contributes two patches for the janz-ican3 driver. In
the first patch, the documentation for already existing sysfs entries
is added, the second patch adds support for another module/firmware
variant. A patch by Shawn Landden makes the padding in the struct
can_frame explicit. The next 4 patches target the flexcan driver, the
first one is by David Jander adding some documentation, the reaming
three by me add more documentation and two small code cleanups.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add macb_change_mtu callback; if jumbo frame support is present allow
mtu size changes upto (jumbo max length allowed - headers).
Signed-off-by: NHarini Katakam <harinik@xilinx.com>
Reviewed-by: NPunnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable jumbo frame support for Zynq Ultrascale+ MPSoC.
Update the NWCFG register and descriptor length masks accordingly.
Jumbo max length register should be set according to support in SoC; it is
set to 10240 for Zynq Ultrascale+ MPSoC.
Signed-off-by: NHarini Katakam <harinik@xilinx.com>
Reviewed-by: NPunnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add compatible string and config structure for Zynq Ultrascale+ MPSoC
Signed-off-by: NHarini Katakam <harinik@xilinx.com>
Reviewed-by: NPunnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add "cdns,zynqmp-gem" to be used for Zynq Ultrascale+ MPSoC.
Signed-off-by: NHarini Katakam <harinik@xilinx.com>
Reviewed-by: NPunnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under tcp memory pressure, calling epoll_wait() in edge triggered
mode after -EAGAIN, can result in an indefinite hang in epoll_wait(),
even when there is sufficient memory available to continue making
progress. The problem is that when __sk_mem_schedule() returns 0
under memory pressure, we do not set the SOCK_NOSPACE flag in the
tcp write paths (tcp_sendmsg() or do_tcp_sendpages()). Then, since
SOCK_NOSPACE is used to trigger wakeups when incoming acks create
sufficient new space in the write queue, all outstanding packets
are acked, but we never wake up with the the EPOLLOUT that we are
expecting from epoll_wait().

This issue is currently limited to epoll() when used in edge trigger
mode, since 'tcp_poll()', does in fact currently set SOCK_NOSPACE.
This is sufficient for poll()/select() and epoll() in level trigger
mode. However, in edge trigger mode, epoll() is relying on the write
path to set SOCK_NOSPACE. EPOLL(7) says that in edge-trigger mode we
can only call epoll_wait() after read/write return -EAGAIN. Thus, in
the case of the socket write, we are relying on the fact that
tcp_sendmsg()/network write paths are going to issue a wakeup for
us at some point in the future when we get -EAGAIN.

Normally, epoll() edge trigger works fine when we've exceeded the
sk->sndbuf because in that case we do set SOCK_NOSPACE. However, when
we return -EAGAIN from the write path b/c we are over the tcp memory
limits and not b/c we are over the sndbuf, we are never going to get
another wakeup.

I can reproduce this issue, using SO_SNDBUF, since __sk_mem_schedule()
will return 0, or failure more readily with SO_SNDBUF:

1) create socket and set SO_SNDBUF to N
2) add socket as edge trigger
3) write to socket and block in epoll on -EAGAIN
4) cause tcp mem pressure via: echo "<small val>" > net.ipv4.tcp_mem

The fix here is simply to set SOCK_NOSPACE in sk_stream_wait_memory()
when the socket is non-blocking. Note that SOCK_NOSPACE, in addition
to waking up outstanding waiters is also used to expand the size of
the sk->sndbuf. However, we will not expand it by setting it in this
case because tcp_should_expand_sndbuf(), ensures that no expansion
occurs when we are under tcp memory pressure.

Note that we could still hang if sk->sk_wmem_queue is 0, when we get
the -EAGAIN. In this case the SOCK_NOSPACE bit will not help, since we
are waiting for and event that will never happen. I believe
that this case is harder to hit (and did not hit in my testing),
in that over the tcp 'soft' memory limits, we continue to guarantee a
minimum write buffer size. Perhaps, we could return -ENOSPC in this
case, or maybe we simply issue a wakeup in this case, such that we
keep retrying the write. Note that this case is not specific to
epoll() ET, but rather would affect blocking sockets as well. So I
view this patch as bringing epoll() edge-trigger into sync with the
current poll()/select()/epoll() level trigger and blocking sockets
behavior.
Signed-off-by: NJason Baron <jbaron@akamai.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use device flag IFF_LIVE_ADDR_CHANGE to signal that
the device supports changing the hardware address when
the device is running.
This allows eth_mac_addr() to change the mac address
also when the network device's interface is open.
This capability is required by certain applications,
like bonding mode 6 (Adaptive Load Balancing).
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle TxFIFO underrun exceptions outside the fast path.
A controller reset is more reliable in this exceptional
case, as opposed to re-enabling on-the-fly the Tx DMA.

As the controller reset is handled outside the fast path
by the reset_gfar() workqueue handler, the locking
scheme on the Tx path is significantly simplified.
Because the Tx processing (xmit queues and tx napi) is
disabled during controller reset, tstat access from xmit
does not require locking.  So the scope of the txlock on
the processing path is now reduced to num_txbdfree, which
is shared only between process context (xmit) and softirq
(clean_tx_ring).  As a result, the txlock must not guard
against interrupt context, and the spin_lock_irqsave()
from xmit can be replaced by spin_lock_bh().  Likewise,
the locking has been downgraded for clean_tx_ring().
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
BPF updates

This set gets rid of BPF special handling in seccomp filter preparation
and provides generic infrastructure from BPF side, which eventually also
allows for classic BPF JITs to add support for seccomp filters.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Seccomp has always been a special candidate when it comes to preparation
of its filters in seccomp_prepare_filter(). Due to the extra checks and
filter rewrite it partially duplicates code and has BPF internals exposed.

This patch adds a generic API inside the BPF code code that seccomp can use
and thus keep it's filter preparation code minimal and better maintainable.
The other side-effect is that now classic JITs can add seccomp support as
well by only providing a BPF_LDX | BPF_W | BPF_ABS translation.

Tested with seccomp and BPF test suites.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Cc: Nicolas Schichan <nschichan@freebox.fr>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When seccomp BPF was added, it was discussed to add __GFP_NOWARN
flag for their configuration path as f.e. up to 32K allocations are
more prone to fail under stress. As we're going to reuse BPF API,
add __GFP_NOWARN flags where larger kmalloc() and friends allocations
could fail.

It doesn't make much sense to pass around __GFP_NOWARN everywhere as
an extra argument only for seccomp while we just as well could run
into similar issues for socket filters, where it's not desired to
have a user application throw a WARN() due to allocation failure.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Cc: Nicolas Schichan <nschichan@freebox.fr>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the calls to bpf_check_classic(), bpf_convert_filter() and
bpf_migrate_runtime() and let bpf_prepare_filter() take care of that
instead.

seccomp_check_filter() is passed to bpf_prepare_filter() so that it
gets called from there, after bpf_check_classic().

We can now remove exposure of two internal classic BPF functions
previously used by seccomp. The export of bpf_check_classic() symbol,
previously known as sk_chk_filter(), was there since pre git times,
and no in-tree module was using it, therefore remove it.

Joint work with Daniel Borkmann.
Signed-off-by: NNicolas Schichan <nschichan@freebox.fr>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is in preparation for use by the seccomp code, the rationale is
not to duplicate additional code within the seccomp layer, but instead,
have it abstracted and hidden within the classic BPF API.

As an interim step, this now also makes bpf_prepare_filter() visible
(not as exported symbol though), so that seccomp can reuse that code
path instead of reimplementing it.

Joint work with Daniel Borkmann.
Signed-off-by: NNicolas Schichan <nschichan@freebox.fr>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2015-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Lots of updates for net-next for this cycle. As usual, we have
a lot of small fixes and cleanups, the bigger items are:
 * proper mac80211 rate control locking, to fix some random crashes
   (this required changing other locking as well)
 * mac80211 "fast-xmit", a mechanism to reduce, in most cases, the
   amount of code we execute while going from ndo_start_xmit() to
   the driver
 * this also clears the way for properly supporting S/G and checksum
   and segmentation offloads
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
tcp: more reliable window probes

This series address a problem caused by small rto_min timers in DC,
leading to either timer storms or early flow terminations.

We also add two new SNMP counters for proper monitoring :
TCPWinProbe and TCPKeepAlive

v2: added TCPKeepAlive counter, as suggested by Yuchung & Neal
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Diagnosing problems related to Window Probes has been hard because
we lack a counter.

TCPWinProbe counts the number of ACK packets a sender has to send
at regular intervals to make sure a reverse ACK packet opening back
a window had not been lost.

TCPKeepAlive counts the number of ACK packets sent to keep TCP
flows alive (SO_KEEPALIVE)
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NNandita Dukkipati <nanditad@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the advent of small rto timers in datacenter TCP,
(ip route ... rto_min x), the following can happen :

1) Qdisc is full, transmit fails.

   TCP sets a timer based on icsk_rto to retry the transmit, without
   exponential backoff.
   With low icsk_rto, and lot of sockets, all cpus are servicing timer
   interrupts like crazy.
   Intent of the code was to retry with a timer between 200 (TCP_RTO_MIN)
   and 500ms (TCP_RESOURCE_PROBE_INTERVAL)

2) Receivers can send zero windows if they don't drain their receive queue.

   TCP sends zero window probes, based on icsk_rto current value, with
   exponential backoff.
   With /proc/sys/net/ipv4/tcp_retries2 being 15 (or even smaller in
   some cases), sender can abort in less than one or two minutes !
   If receiver stops the sender, it obviously doesn't care of very tight
   rto. Probability of dropping the ACK reopening the window is not
   worth the risk.

Lets change the base timer to be at least 200ms (TCP_RTO_MIN) for these
events (but not normal RTO based retransmits)

A followup patch adds a new SNMP counter, as it would have helped a lot
diagnosing this issue.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The legacy netlink API treated EPERM (permission denied) as
"operation not supported".
Reported-by: NTomi Ollila <tomi.ollila@iki.fi>
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the ability to get or set the broadcast link window through the
new netlink API. The functionality was unintentionally missing from
the new netlink API. Adding this means that we also fix the breakage
in the old API when coming through the compat layer.

Fixes: 37e2d484 (tipc: convert legacy nl link prop set to nl compat)
Reported-by: NTomi Ollila <tomi.ollila@iki.fi>
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Default link properties can be set for media or bearer. This
functionality was missed when introducing the NL compatibility layer.

This patch implements this functionality in the compat netlink
layer. It works the same way as it did in the old API. We search for
media and bearers matching the "link name". If we find a matching
media or bearer the link tolerance, priority or window is used as
default for new links on that media or bearer.

Fixes: 37e2d484 (tipc: convert legacy nl link prop set to nl compat)
Reported-by: NTomi Ollila <tomi.ollila@iki.fi>
Signed-off-by: NRichard Alpe <richard.alpe@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implements t4_init_rss_mode() to initialize the rss_mode for all the ports. If
Tunnel All Lookup isn't specified in the global RSS Configuration, then we need
to specify a default Ingress Queue for any ingress packets which aren't hashed.
We'll use our first ingress queue.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sathya Perla says:

====================
be2net: patch-set

The following patch-set has two new feature additions, and a few
minor fixes and cleanups.
Pls consider applying to the net-next tree. Thanks.

v2 changes:
        a) dropped the "don't enable pause by default" patch
        b) described how the "spoof check" works in patch 1's commit log
	c) I had to update our email addresses from "@emulex" to
	   "@avagotech". I'll send a separate patch updating the
	   maintainers

Patch 1 adds support for the "spoofchk" knob for VFs.
When it is enabled, "spoof checking" is done for both MAC-address
and VLAN. For each VF, the HW ensures that the source MAC address
(or vlan) of every outgoing packet of the VF exists in the MAC-list
(or vlan-list) configured for RX filtering for that VF.
If not, the packet is dropped and an error is reported to the driver
in the TX completion.

Patch 2 improves interrupt moderation on Skyhawk-R chip by using
the EQ-DB mechanism to set a "re-arm to interrupt" delay. Currently
interrupt moderation is adjusted by calculating and configuring an
EQ-delay every second. This is done via a FW-cmd. This patch uses
the EQ_DB facility to calculate and set the interrupt delay every 1ms.
This helps moderating interrupts better when the traffic is bursty.

Patch 3 adds L3/L4 error accounting to BE3 VFs, by passing L3/4 error
packets to the network stack.

Patch 4 adds an extra FW-cmd error value check in the driver to identify
an "out of vlan filters" scenario.

Patch 5 stops enabling pause by default as this setting fails in
some HW-configs where priority pause is enabled in FW. If the user
tries to do the same, an appropriate error is returned via ethtool.

Patch 5 posts the full RXQ in be_open() to prevent packet drops due to
bursty traffic when the interface is enabled.

Patch 6 refactors the be_check_ufi_compatibility() routine, that checks
to see if a UFI file meant for a lower rev of a chip is being flashed
on a higher rev, to make it simpler.

Patch 7 replaces the usage of !be_physfn() macro with be_virtfn()
that is already avialble in the driver.

Patch 8 updates the year in the copyright text to 2015.

Path 9 bumps up the driver version to 10.6.02.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVasundhara Volam <vasundhara.volam@avagotech.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use be_virtfn() to determine a VF instead of !be_physfn() for better
readability.
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code in be_check_ufi_compatibility() checks to see if a UFI file meant
for a lower rev of a chip is being flashed on a higher rev, which is
disallowed. This patch re-writes the code needed for this check in a much
simpler manner.
Signed-off-by: NVasundhara Volam <vasundhara.volam@avagotech.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an RXQ is created in be_open(), the driver currently posts only
64 buffers. This sometimes results in packet drops when there is a traffic
burst as soon as the interface is enabled.
This patch fixes this problem by posting the full RXQ on interface enable.
Signed-off-by: NSuresh Reddy <Suresh.Reddy@avagotech.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the FW runs out of vlan filters it can either return an
INSUFFICIENT_RESOURCES error or an INSUFFICIENT_VLANS error.
The driver currently checks only for the former error value.
This patch adds a check for the latter value too.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>