This patch moves the MAC HW initialization and
the HW feature verification from the open to the probe
function as D. Miller suggested.
So the patch actually reorganizes and tidies-up some parts of
the driver and indeed fixes some problem when tune its HW features.
These can be overwritten by looking at the HW cap register at
run-time and that generated problems.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of we use an external Wake-Up IRQ line
(priv->wol_irq != dev->irq) we need to invoke the
request_irq.
Signed-off-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If this bit is set and the CRC error is reset, then the packet is valid.
Only report this as stat info.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BugLink: http://bugs.launchpad.net/bugs/900802

Cc: stable@vger.kernel.org 3.2+
Signed-off-by: NTill Kamppeter <till.kamppeter@gmail.com>
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add unicast steering entries to resource tracker.
Do qp_detach also for these entries when VF doesn't shut down gracefully.
Otherwise there is leakage of these resources, since they are not tracked.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When adding new unicast steer entry, before moving qp to state ready,
actually before calling mlx4_RST2INIT_QP_wrapper(), there were added
a lot of entries with local_qpn=0 into radix tree.
This fact impacted the get_res() function and proper functioning
of resource tracker in addition to adding trash entries into radix tree.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@melllanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When passing MLX4_UC_STEER=1 it was translated to value 2
after mlx4_QP_ATTACH_wrapper. Therefore in new_steering_entry()
unicast steer entries were added to index 2 of array of size 2.
Fixing this bug by shift right to one position.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

Jean Delvare reported bonding on top of 3c59x adapters was not detecting
network cable removal fast enough.

3c59x indeed uses a 60 seconds timer to check link status if carrier is
on, and 5 seconds if carrier is off.

This patch reduces timer period to 5 seconds if device is a bonding
slave.
Reported-by: NJean Delvare <jdelvare@suse.de>
Acked-by: NJean Delvare <jdelvare@suse.de>
Acked-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 5a698af5 (bond: service netpoll arp queue on master device)
tested IFF_SLAVE flag against dev->priv_flags instead of dev->flags
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: WANG Cong <amwang@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first parameter should be "number of elements" and the second parameter
should be "element size".
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'poll' was a debugging option, but turning it on these days leads to
kernel panic. Remove it.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit ensures that lost_cnt_hint is correctly updated in
tcp_shifted_skb() for FACK TCP senders. The lost_cnt_hint adjustment
in tcp_sacktag_one() only applies to non-FACK senders, so FACK senders
need their own adjustment.

This applies the spirit of 1e5289e1 -
except now that the sequence range passed into tcp_sacktag_one() is
correct we need only have a special case adjustment for FACK.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fix a similar problem as in 72092cc4
and 481a8199 ("can:
fix NOHZ local_softirq_pending 08 warning"). This fix replaces netif_rx()
with netif_rx_ni() which has to be used from process/softirq context.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 619c5cb6 (New 7.0 FW: bnx2x, cnic, bnx2i, bnx2fc) added new
sparse warnings.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Vladislav Zolotarov <vladz@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 0869b3a4: ixp4xx-eth: use an unique MDIO bus name changed
the MDIO bus name from "0" to "ixp4xx-eth-0", as a result the PHY
name is not longer appropriate and will not match the MDIO bus name
so PHY connection will not succeed, fix that.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit "d6c25beb: mdio-octeon: use an unique MDIO bus name" changed the
octeon MDIO bus name from "0" to "mdio-octeon-0", change the PHY
formatting logic to account for that name change, so that PHY connection
on this bus succeeds.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit "391420f7: fec: use an unique MDIO bus name" first modified
the MDIO bus name to include the platform name, then in commit
"a7ed07d5: net: fec: correct phy_name buffer length when init phy_name"
the PHY name formatting was fixed in the case the PHY matches a PHY
driver.

The FEC driver however, also handles the case where we want to attach
to the fixed MDIO bus name, which was previously named "0", and now
"fixed-0". Change the PHY formatting logic to account for that.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 3e617506: bcm63xx_enet: use an unique MDIO bus name introduced
a regression in the PHY connection logic, since the PHY name was formatted
to expect the bus name to be "0" or "1", whereas it is now "bcm63xx-enet-0"
or "bcm63xx-enet-1".
Reported-by: NJoel EJC <joel_ejc@yahoofr>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d1733f07: cpmac: use an unique MDIO bus name changed the MDIO bus
name from "1" to "cpmac-1", this breaks the PHY connection logic because
the PHY name still uses the old bus names "0" and "1", fix that to
always use the mdio bus id instead.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first parameter should be "number of elements" and the second parameter
should be "element size".
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the newly-SACKed range to be the range of newly-shifted bytes.

Previously - since 832d11c5 -
tcp_shifted_skb() incorrectly called tcp_sacktag_one() with the start
and end sequence numbers of the skb it passes in set to the range just
beyond the range that is newly-SACKed.

This commit also removes a special-case adjustment to lost_cnt_hint in
tcp_shifted_skb() since the pre-existing adjustment of lost_cnt_hint
in tcp_sacktag_one() now properly handles this things now that the
correct start sequence number is passed in.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit allows callers of tcp_sacktag_one() to pass in sequence
ranges that do not align with skb boundaries, as tcp_shifted_skb()
needs to do in an upcoming fix in this patch series.

In fact, now tcp_sacktag_one() does not need to depend on an input skb
at all, which makes its semantics and dependencies more clear.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Quoth David:

1) GRO MAC header comparisons were ethernet specific, breaking other
   link types.  This required a multi-faceted fix to cure the originally
   noted case (Infiniband), because IPoIB was lying about it's actual
   hard header length.  Thanks to Eric Dumazet, Roland Dreier, and
   others.

2) Fix build failure when INET_UDP_DIAG is built in and ipv6 is modular.
   From Anisse Astier.

3) Off by ones and other bug fixes in netprio_cgroup from Neil Horman.

4) ipv4 TCP reset generation needs to respect any network interface
   binding from the socket, otherwise route lookups might give a
   different result than all the other segments received.  From Shawn
   Lu.

5) Fix unintended regression in ipv4 proxy ARP responses, from Thomas
   Graf.

6) Fix SKB under-allocation bug in sh_eth, from Yoshihiro Shimoda.

7) Revert skge PCI mapping changes that are causing crashes for some
   folks, from Stephen Hemminger.

8) IPV4 route lookups fill in the wildcarded fields of the given flow
   lookup key passed in, which is fine most of the time as this is
   exactly what the caller's want.  However there are a few cases that
   want to retain the original flow key values afterwards, so handle
   those cases properly.  Fix from Julian Anastasov.

9) IGB/IXGBE VF lookup bug fixes from Greg Rose.

10) Properly null terminate filename passed to ethtool flash device
    method, from Ben Hutchings.

11) S3 resume fix in via-velocity from David Lv.

12) Fix double SKB free during xmit failure in CAIF, from Dmitry
    Tarnyagin.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
  net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
  ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
  netprio_cgroup: fix wrong memory access when NETPRIO_CGROUP=m
  netprio_cgroup: don't allocate prio table when a device is registered
  netprio_cgroup: fix an off-by-one bug
  bna: fix error handling of bnad_get_flash_partition_by_offset()
  isdn: type bug in isdn_net_header()
  net: Make qdisc_skb_cb upper size bound explicit.
  ixgbe: ethtool: stats user buffer overrun
  ixgbe: dcb: up2tc mapping lost on disable/enable CEE DCB state
  ixgbe: do not update real num queues when netdev is going away
  ixgbe: Fix broken dependency on MAX_SKB_FRAGS being related to page size
  ixgbe: Fix case of Tx Hang in PF with 32 VFs
  ixgbe: fix vf lookup
  igb: fix vf lookup
  e1000: add dropped DMA receive enable back in for WoL
  gro: more generic L2 header check
  IPoIB: Stop lying about hard_header_len and use skb->cb to stash LL addresses
  zd1211rw: firmware needs duration_id set to zero for non-pspoll frames
  net: enable TC35815 for MIPS again
  ...

Commit 653241 (net: RFC3069, private VLAN proxy arp support) changed
the behavior of arp proxy to send arp replies back out on the interface
the request came in even if the private VLAN feature is disabled.

Previously we checked rt->dst.dev != skb->dev for in scenarios, when
proxy arp is enabled on for the netdevice and also when individual proxy
neighbour entries have been added.

This patch adds the check back for the pneigh_lookup() scenario.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NJesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fix a bug which introduced by commit ac8a4810 (ipv4: Save
nexthop address of LSRR/SSRR option to IPCB.).In that patch, we saved
the nexthop of SRR in ip_option->nexthop and update iph->daddr until
we get to ip_forward_options(), but we need to update it before
ip_rt_get_source(), otherwise we may get a wrong src.
Signed-off-by: NLi Wei <lw@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the netprio_cgroup module is not loaded, net_prio_subsys_id
is -1, and so sock_update_prioidx() accesses cgroup_subsys array
with negative index subsys[-1].

Make the code resembles cls_cgroup code, which is bug free.
Origionally-authored-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So we delay the allocation till the priority is set through cgroup,
and this makes skb_update_priority() faster when it's not set.

This also eliminates an off-by-one bug similar with the one fixed
in the previous patch.
Origionally-authored-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

# mount -t cgroup xxx /mnt
  # mkdir /mnt/tmp
  # cat /mnt/tmp/net_prio.ifpriomap
  lo 0
  eth0 0
  virbr0 0
  # echo 'lo 999' > /mnt/tmp/net_prio.ifpriomap
  # cat /mnt/tmp/net_prio.ifpriomap
  lo 999
  eth0 0
  virbr0 4101267344

We got weired output, because we exceeded the boundary of the array.
We may even crash the kernel..
Origionally-authored-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
  drm/i915: no lvds quirk for AOpen MP45
  drm/i915: Force explicit bpp selection for intel_dp_link_required
  drm/radeon: do not continue after error from r600_ib_test
  drivers/gpu/drm/drm_ioc32.c: initialize all fields
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
  drm/i915:: Disable FBC on SandyBridge

fix 1 mysterious divide error
fix 3 NULL dereference bugs in writeback tracing, on SD card removal w/o umount

* tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
  writeback: fix dereferencing NULL bdi->dev on trace_writeback_queue
  lib: proportion: lower PROP_MAX_SHIFT to 32 on 64-bit kernel
  writeback: fix NULL bdi->dev in trace writeback_single_inode
  backing-dev: fix wakeup timer races with bdi_unregister()

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix double start/stop in x86_pmu_start()
  perf evsel: Fix an issue where perf report fails to show the proper percentage
  perf tools: Fix prefix matching for kernel maps
  perf tools: Fix perf stack to non executable on x86_64
  perf: Remove deprecated WARN_ON_ONCE()

Couple of regressions, couple of zero-day bugs, a minor enhancement.
Nothing really major.

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (f75375s) Let f75375_update_device treat pwmX as a measured value
  hwmon: (f75375s) Fix bit shifting in f75375_write16
  hwmon: (f75375s) Fix reading of wrong register when initializing the F75387
  hwmon: (f75375s) Fix automatic pwm mode setting for F75373 & F75375
  hwmon: (w83627ehf) Remove duplicate code

Merge branch 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux into drm-fixes

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux:
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
  drm/i915: no lvds quirk for AOpen MP45
  drm/i915: Force explicit bpp selection for intel_dp_link_required
  drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
  drm/i915:: Disable FBC on SandyBridge

Serial/TTY fixes for the 3.3-rc3 tree

Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial: omap-serial: wakeup latency constraint is in microseconds, not milliseconds
  tty: serial: OMAP: block idle while the UART is transferring data in PIO mode
  tty: serial: OMAP: use a 1-byte RX FIFO threshold in PIO mode
  m32r: relocate drivers back out of 8250 dir
  tty: fix a build failure on sparc
  serial: samsung: Add support for EXYNOS5250
  serial: samsung: Add support for EXYNOS4212 and EXYNOS4412
  drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layer

Staging tree patches for 3.3-rc3

Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.

Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
  staging: pohmelfs: remove drivers/staging/pohmelfs
  staging: android/ram_console: Don't build on arches w/o ioremap
  staging: r8712u: Use asynchronous firmware loading
  staging: usbip: fix to prevent potentially using uninitialized spinlock
  staging: r8712u: Fix problem when CONFIG_R8712_AP is set
  staging: tidspbridge: fix incorrect free to drv_datap
  staging: tidspbridge: fix bridge_open memory leaks
  staging: android: lowmemorykiller: Don't wait more than one second for a process to die
  MAINTAINERS: staging: iio: add iio information
  staging: zcache: fix serialization bug in zv stats
  staging: fix go7007-usb license
  Staging: android: binder: Fix crashes when sharing a binder file between processes
  Staging: android: Remove pmem driver
  Staging: asus_oled: fix NULL-ptr crash on unloading
  Staging: asus_oled: fix image processing
  Staging: android: binder: Don't call dump_stack in binder_vma_open
  staging: r8712u: Add new Sitecom UsB ID
  zcache: Set SWIZ_BITS to 8 to reduce tmem bucket lock contention.
  zcache: fix deadlock condition
  staging: drm/omap: fix locking issue
  ...

Driver core fixes for the 3.3-rc3 tree.

A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver-core: cpu: fix kobject warning when hotplugging a cpu
  ACPI: remove duplicated lines of merging problems with acpi_processor_add
  docbook: fix fatal errors in device-drivers docbook and add DMA Management section
  drivers/base/memory.c: fix memory_dev_init() long delay
  driver core: cpu: remove kernel warning when removing a cpu

Minor char-misc fixes for 3.3-rc3

Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mmc: cb710 core: Add missing spin_lock_init for irq_lock of struct cb710_chip
  cs5535-mfgpt: don't call __init function from __devinit
  vmw_balloon: fix for a -Wuninitialized warning
  drivers: misc: Remove MISC_DEVICES config option
  c2port: fix build error for duramar2150 due to missing header.

USB fixes for 3.3-rc3

Here are a few minor USB fixes and a bunch of device id updates for the
USB drivers.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

* tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: usbserial: add new PID number (0xa951) to the ftdi driver
  usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
  usb: musb: fix a build error on mips
  uwb & wusb & usb wireless controllers: fix kconfig error & build errors
  usb: Skip PCI USB quirk handling for Netlogic XLP
  powerpc/usb: fix issue of CPU halt when missing USB PHY clock
  usb: otg: mv_otg: Add dependence
  usb: host: Distinguish Kconfig text for Freescale controllers
  USB: add new zte 3g-dongle's pid to option.c
  usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
  USB: qcserial: don't enable autosuspend
  USB: qcserial: add several new serial devices
  usb: otg: mv_otg: Add dependence
  usb: gadget: zero: fix bug in loopback autoresume handling

The current error handling doesn't work because we flash_part is a u32
so the checks for negative error codes don't work.  I considered making
things signed but I don't know the hardware enough to say if that's a
problem.  Really, we don't use the error codes so just returning zero
for all problems is fine.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>