An AP can send an operating channel width change in a beacon
opmode notification IE as long as there's a change in the nss as
well (See 802.11ac-2013 section 10.41).
So don't limit updating to nss only from an opmode notification IE.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When the AP is advertising limited TX power, the message can be
printed over and over again. Suppress it when the power level
isn't changing.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=106011Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

During reprogramming, mac80211 currently first adds all the channel
contexts, then binds them to the vifs and then goes to reconfigure
all the interfaces. Drivers might, perhaps implicitly, rely on the
operation order for certain things that typically happen within a
single function elsewhere in mac80211. To avoid problems with that,
reorder the code in mac80211's restart/reprogramming to work fully
within the interface loop so that the order of operations is like
in normal operation.

For iwlwifi, this fixes a firmware crash when reprogramming with an
AP/GO interface active.
Reported-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When reconfiguration during resume fails while a scan is pending
for completion work, that work will never run, and the scan will
be stuck forever. Factor out the code to recover this and call it
also in ieee80211_handle_reconfig_failure().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In the last change here, I neglected to update the cookie in one code
path: when a mgmt-tx has no real cookie sent to userspace as it doesn't
wait for a response, but is off-channel. The original code used the SKB
pointer as the cookie and always assigned the cookie to the TX SKB in
ieee80211_start_roc_work(), but my change turned this around and made
the code rely on a valid cookie being passed in.

Unfortunately, the off-channel no-wait TX path wasn't assigning one at
all, resulting in an uninitialized stack value being used. This wasn't
handed back to userspace as a cookie (since in the no-wait case there
isn't a cookie), but it was tested for non-zero to distinguish between
mgmt-tx and off-channel.

Fix this by assigning a dummy non-zero cookie unconditionally, and get
rid of a misleading comment and some dead code while at it. I'll clean
up the ACK SKB handling separately later.

Fixes: 3b79af97 ("mac80211: stop using pointers as userspace cookies")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

DFS channels should not be actively scanned as we can't be sure
if we are allowed or not.

If the current channel is in the DFS band, active scan might be
performed after CSA, but we have no guarantee about other channels,
therefore it is safer to prevent active scanning at all.

Cc: stable@vger.kernel.org
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Interfaces are being initialized (setup) on addition,
and torn down on removal.

However, p2p device is being torn down when stopped,
resulting in the next p2p start operation being done
on uninitialized interface.

Solve it by calling ieee80211_teardown_sdata() only
on interface removal (for the non-netdev case).
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
[squashed in fix to call teardown after unregister]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Advertising reordering window in ADDBA less than 64 can crash some APs,
an example is LinkSys WRT120N (with FW v1.0.07 build 002 Jun 18 2012).
On the other hand, a driver may need to limit Tx A-MPDU size for its own
reasons, like specific HW limitations.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We can't update the Tx power on the device unless it is
running.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=101521.

Cc: stable@vger.kernel.org
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When using call_rcu(), the called function may be delayed quite
significantly, and without a matching rcu_barrier() there's no
way to be sure it has finished.
Therefore, global state that could be gone/freed/reused should
never be touched in the callback.

Fix this in mesh by moving the atomic_dec() into the caller;
that's not really a problem since we already unlinked the path
and it will be destroyed anyway.

This fixes a crash Jouni observed when running certain tests in
a certain order, in which the mesh interface was torn down, the
memory reused for a function pointer (work struct) and running
that then crashed since the pointer had been decremented by 1,
resulting in an invalid instruction byte stream.

Cc: stable@vger.kernel.org
Fixes: eb2b9311 ("mac80211: mesh path table implementation")
Reported-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

For now, this feature doesn't actually work. To avoid shipping a
kernel that has it enabled but where it can't be used disable it
for now - we can re-enable it when it's fixed.

This partially reverts 44674d9c ("mac80211: advertise support
for full station state in AP mode").

Cc: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Channel context driver operations can sleep, so add might_sleep()
and document this.
Signed-off-by: NChaitanya T K <chaitanya.mgit@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow distinguishing the non-station case from the case of a
station without rates, by using -1 for the non-station case.
This value cannot be reached with a station since that many
legacy rates don't exist.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

As WMM is required for HT/VHT operation, treat bad WMM parameters
more gracefully by falling back to default parameters instead of
not using WMM assocation. This makes it possible to still use HT
or VHT, although potentially with reduced quality of service due
to unintended WMM parameters.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Disabling WMM has a huge impact these days. It implies that
HT and VHT will be disabled which means that the throughput
will be drammatically reduced.
Since the AIFSN is a transmission parameter, we can play a
bit and fix it up to make it compliant with the 802.11
specification which requires it to be at least 2.
Increasing it from 1 to 2 will slightly reduce the
likelyhood to get a transmission opportunity compared to
other clients that would accept to set AIFSN=1, but at
least it will allow HT and VHT which is a huge gain.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The function currently determines this value, for use in bss_info.qos,
based on the interface type itself. Make it a parameter instead and
set it with the same logic for now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

llid_in_use needs to be limited to stations of the same VIF, otherwise it
will cause a NULL deref as the sta_info of non-mesh-VIFs don't have
sta->mesh set.

Steps to reproduce:

   modprobe mac80211_hwsim channels=2
   iw phy phy0 interface add ibss0 type ibss
   iw phy phy0 interface add mesh0 type mp
   iw phy phy1 interface add ibss1 type ibss
   iw phy phy1 interface add mesh1 type mp
   ip link set ibss0 up
   ip link set mesh0 up
   ip link set ibss1 up
   ip link set mesh1 up
   iw dev ibss0 ibss join foo 2412
   iw dev ibss1 ibss join foo 2412
   # Ensure that ibss0 and ibss1 are actually associated; I often need to
   # leave and join the cell on ibss1 a second time.
   iw dev mesh0 mesh join bar
   iw dev mesh1 mesh join bar # crash
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When 11n peers performs a TDLS connection on a legacy BSS, the HT
operation IE must be specified according to IEEE802.11-2012 section
9.23.3.2. Otherwise HT-protection is compromised and the medium becomes
noisy for both the TDLS and the BSS links.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Scheduled scan has to be reconfigured only if wowlan wasn't
configured, since otherwise it should continue to run (with
the 'any' trigger) or be aborted.

The current code will end up asking the driver to start a new
scheduled scan without stopping the previous one, and leaking
some memory (from the previous request.)

Fix this by doing the abort/restart under the proper conditions.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If drv_start() fails during hw_restart, all the running
interfaces are being closed/stopped, which results in
drv_stop() being called, although the driver was never
started successfully.

This might cause drivers to perform operations on uninitialized
memory (as they assume it was initialized on drv_start)

Consider the local->started flag, and call the driver's stop()
op only if drv_start() succeeded before.

Move drv_start() and drv_stop() to driver-ops.c, as they are no
longer simple wrappers.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The recalc_smps work can run after the station disassociates.
At this stage we already released the channel, but the work
will be cancelled only when the interface stops.
In this scenario we can hit the warning in ieee80211_recalc_smps, so
just remove it.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Requesting hw restart during suspend might result
in the restart work being executed after mac80211
and the hw are suspended.

Solve the race by simply scheduling the restart
work on a freezable workqueue.

Note that there can be some cases of reconfiguration
on resume (besides the hardware restart):

* wowlan is not configured -
    All the interfaces removed were removed on suspend,
    and drv_stop() was called. At this point the driver
    shouldn't expect for hw_restart anyway, so we can
    simply cancel it (on resume).

* wowlan is configured, drv_resume() == 1
    There is no definitive expected behavior in this case,
    as each driver might have different expectations (e.g.
    setting some flags on suspend/restart vs. not handling
    spurious recovery).
    For now, simply let the hw_restart work run again after
    resume, and hope the driver will handle it well (or at
    least initiate another hw restart).
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Local request to deauthenticate wasn't handled while associating, thus
the association could continue even when the user space required to
disconnect.

Cc: stable@vger.kernel.org
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In TDLS channel-switch operations the chandef can sometimes be NULL.
Avoid an oops in the trace code for these cases and just print a
chandef full of zeros.

Cc: stable@vger.kernel.org
Fixes: a7a6bdd0 ("mac80211: introduce TDLS channel switch ops")
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In case of one shot NOA the interval can be 0, catch that
instead of potentially (depending on the driver) crashing
like this:

divide error: 0000 [#1] SMP
[...]
Call Trace:
<IRQ>
[<ffffffffc08e891c>] ieee80211_extend_absent_time+0x6c/0xb0 [mac80211]
[<ffffffffc08e8a17>] ieee80211_update_p2p_noa+0xb7/0xe0 [mac80211]
[<ffffffffc069cc30>] ath9k_p2p_ps_timer+0x170/0x190 [ath9k]
[<ffffffffc070adf8>] ath_gen_timer_isr+0xc8/0xf0 [ath9k_hw]
[<ffffffffc0691156>] ath9k_tasklet+0x296/0x2f0 [ath9k]
[<ffffffff8107ad65>] tasklet_action+0xe5/0xf0
[...]

Cc: stable@vger.kernel.org [3.16+, due to d463af4a using it]
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Group station statistics by where they're (mostly) updated
(TX, RX and TX-status) and group them into sub-structs of
the struct sta_info.

Also rename the variables since the grouping now makes it
obvious where they belong.

This makes it easier to identify where the statistics are
updated in the code, and thus easier to think about them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's little point in keeping (and even sending to userspace)
the beacon_loss_count value per station, since it can only apply
to the AP on a managed-mode connection. Move the value to ifmgd,
advertise it only in managed mode, and remove it from ethtool as
it's available through better interfaces.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This file only feeds a debugfs file that isn't very useful, so remove
it. If necessary, we can add other ways to get this information, for
example in the NL80211_CMD_PROBE_CLIENT response.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

That file contains just a single function, which itself is just a
single statement to call a different function. Remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The file contains just a single declaration that can easily
move to another file - remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's only a single caller of this function, so it can
be moved to the same file and made static.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Reduce indentation a bit to make the condition more readable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

As this API has never really seen any use and most drivers don't
ever use the value derived from it, remove it.

Change the only driver using it (rt2x00) to simply use the DTIM
period instead of the "max sleep" time.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The new API is more easily extensible with a metadata struct
passed to it, use it in mac80211.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If multiple scan plans were set for scheduled scan, do not restart
scheduled scan on reconfig because it is possible that some scan
plans were already completed and there is no need to run them all
over again. Instead, notify userspace that scheduled scan stopped
so it can configure new scan plans for scheduled scan.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Commit 30686bf7 ("mac80211: convert HW flags to unsigned long
bitmap") accidentally removed the newline delimiter from the hwflags
debugfs file. Fix this by adding back the newline between the HW flags.

Cc: stable@vger.kernel.org [4.2]
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
[fix commit log]
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This reverts commit 5c48f120.

Some device drivers (ath10k) offload part of aggregation including AddBA/DelBA
negotiations to firmware. In such scenario, the PMF configuration of
the station needs to be provided to driver to enable encryption of
AddBA/DelBA action frames.
Signed-off-by: NTamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The function returns always non-negative values.

The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].

[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The mac80211 code uses ktime_get_ts to measure the connected time.
As this uses monotonic time, it is y2038 safe on 32-bit systems,
but we still want to deprecate the use of 'timespec' because most
other users are broken.

This changes the code to use ktime_get_seconds() instead, which
avoids the timespec structure and is slightly more efficient.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>