The allowable range is 0.25 seconds to 1 second interval.  Default is
1 second.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is useful for multi-function devices.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With a default VLAN, the VF has its own VLAN domain and it can receive
all traffic within that domain.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For correctness, the MRU enables bit must be set when passing the
MRU to firmware during vnic configuration.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to the Ethtool FLASHDEV command handler for additional
firmware types to cover all the on-chip processors.
Signed-off-by: NRob Swindell <rob.swindell@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon successful mgmt processor firmware update, request a self
reset upon next PCIe reset (e.g. system reboot).
Signed-off-by: NRob Swindell <rob.swindell@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To support Secure Firmware Update, we must be able to allocate
a staging area in the Flash.  This patch adds support for the
"update" type to tell firmware to do that.
Signed-off-by: NRob Swindell <rob.swindell@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling the firmware to do function reset on the PF will kill all the VFs.
To prevent that, we call function reset on the 1st PF open before any VF
can be activated.  On subsequent PF opens (with possibly some active VFs),
a bit has been set and we'll skip the function reset.  VF driver will
always do function reset on every open.  If there is an AER event, we will
always do function reset.
Signed-off-by: NMichael Chan <michael.chan@broadocm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And update driver version to 1.3.0.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Returning 0 for doing nothing is confusing to the user.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the relevant profile functions to create mlx5e driver instance
serving as VF representor. When SRIOV offloads mode is enabled, each VF
will have a representor netdevice instance on the host.

To do that, we also export set of shared service functions from en_main.c,
such that they can be used by both NIC and repsresentors netdevs.

The newly created representor netdevice has a basic set of net_device_ops
which are the same ndo functions as the NIC netdevice and an ndo of it's
own for phys port name.

The profiling infrastructure allow sharing code between the NIC and the
vport representor even though the representor has only a subset of the
NIC functionality.

The VF reps and the PF which is used in that mode to represent the uplink,
expose switchdev ops. Currently the only op supposed is attr get for the
port parent ID which here serves to identify net-devices belonging to the
same HW E-Switch. Other than that, no offloading is implemented and hence
switching functionality is achieved if one sets SW switching rules, e.g
using tc, bridge or ovs.

Port phys name (ndo_get_phys_port_name) is implemented to allow exporting
to user-space the VF vport number and along with the switchdev port parent
id (phys_switch_id) enable a udev base consistent naming scheme:

SUBSYSTEM=="net", ACTION=="add", ATTR{phys_switch_id}=="<phys_switch_id>", \
        ATTR{phys_port_name}!="", NAME="$PF_NIC$attr{phys_port_name}"

where phys_switch_id is exposed by the PF (and VF reps) and $PF_NIC is
the name of the PF netdevice.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce E-Switch registration/unregister representors functions.

Those functions are called by the mlx5e driver when the PF NIC is
created upon pci probe action regardless of the E-Switch mode (NONE,
LEGACY or OFFLOADS).

Adding basic E-Switch database that will hold the vport represntors
upon creation.

This patch doesn't add any new functionality.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To allow support in representor netdevices where we create more than one
netdevice per NIC, add profiles to the mlx5e driver. The profiling
allows for creation of mlx5e instances with different characteristics.

Each profile implements its own behavior using set of function pointers
defined in struct mlx5e_profile. This is done to allow for avoiding complex
per profix branching in the code.

Currently only the profile for the conventional NIC is implemented,
which is of use when a netdev is created upon pci probe.

This patch doesn't add any new functionality.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the current driver implementation two types of receive queue
tables (RQTs) are in use - direct and indirect.

Change the driver to mark each new created RQT (direct or indirect)
as "enabled". This behaviour is needed for introducing new mlx5e
instances which serve to represent SRIOV VFs.

The VF representors will have only one type of RQTs (direct).

An "enabled" flag is added to each RQT to allow better handling
and code sharing between the representors and the nic netdevices.

This patch doesn't add any new functionality.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current refresh tirs self loopback mechanism, refreshes all the tirs
belonging to the same mlx5e instance to prevent self loopback by packets
sent over any ring of that instance. This mechanism relies on all the
tirs/tises of an instance to be created with the same transport domain
number (tdn).

Change the driver to refresh all the tirs created under the same tdn
regardless of which mlx5e netdev instance they belong to.

This behaviour is needed for introducing new mlx5e instances which serve
to represent SRIOV VFs. The representors and the PF share vport used for
E-Switch management, and we want to avoid NIC level HW loopback between
them, e.g when sending broadcast packets. To achieve that, both the
representors and the PF NIC will share the tdn.

This patch doesn't add any new functionality.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To allow creating more than one netdev over the same PCI function, we
change the driver such that global NIC resources are created once and
later be shared amongst all the mlx5e netdevs running over that port.

Move the CQ UAR, PD (pdn), Transport Domain (tdn), MKey resources from
being kept in the mlx5e priv part to a new resources structure
(mlx5e_resources) placed under the mlx5_core device.

This patch doesn't add any new functionality.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement handlers for the devlink commands to get and set the SRIOV
E-Switch mode.

When turning to the switchdev/offloads mode, we disable the e-switch
and enable it again in the new mode, create the NIC offloads table
and create VF reps.

When turning to legacy mode, we remove the VF reps and the offloads
table, and re-initiate the e-switch in it's legacy mode.

The actual creation/removal of the VF reps is done in downstream patches.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The devlink interface is initially used to set/get the mode of the SRIOV e-switch.

Currently, these are only stubs for get/set, down-stream patch will actually
fill them out.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the API to create vport rx rules of the form

	packet meta-data :: vport == $VPORT --> $TIR

where the TIR is opened by this VF representor.

This logic will by used for packets that didn't match any rule in the
e-switch datapath and should be received into the host OS through the
netdevice that represents the VF they were sent from.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Belongs to the NIC offloads name-space, and to be used as part of the
SRIOV offloads logic to steer packets that hit the e-switch miss rule
to the TIR of the relevant VF representor.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new namespace (MLX5_FLOW_NAMESPACE_OFFLOADS) to be populated
with flow steering rules that deal with rules that have have to
be executed before the EN NIC steering rules are matched.

The namespace is located after the bypass name-space and before the
kernel name-space. Therefore, it precedes the HW processing done for
rules set for the kernel NIC name-space.

Under SRIOV, it would allow us to match on e-switch missed packet
and forward them to the relevant VF representor TIR.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amir@vadai.me>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the API to create send-to-vport e-switch rules of the form

 packet meta-data :: send-queue-number == $SQN and source-vport == 0 --> $VPORT

These rules are to be used for a send-to-vport logic which conceptually bypasses
the "normal" steering rules currently present at the e-switch datapath.

Such rule should apply only for packets that originate in the e-switch manager
vport (0) and are sent for a given SQN which is used by a given VF representor
device, and hence the matching logic.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the sriov offloads mode, packets that are not matched by any other
rule should be sent towards the e-switch manager for further processing.

Add such "miss" rule which matches ANY packet as the last rule in the
e-switch FDB and programs the HW to send the packet to vport 0 where
the e-switch manager runs.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike the legacy mode, here, forwarding rules are not learned by the
driver per events on macs set by VFs/VMs into their vports, but rather
should be programmed by higher-level SW entities.

Saying that, still, in the offloads mode (SRIOV_OFFLOADS), two flow
groups are created by the driver for management (slow path) purposes:

The first group will be used for sending packets over e-switch vports
from the host OS where the e-switch management code runs, to be
received by VFs.

The second group will be used by a miss rule which forwards packets toward
the e-switch manager. Further logic will trap these packets such that
the receiving net-device as seen by the networking stack is the representor
of the vport that sent the packet over the e-switch data-path.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define three modes for the SRIOV e-switch operation, none (SRIOV_NONE,
none of the VF vports are enabled), legacy (SRIOV_LEGACY, the current mode)
and sriov offloads (SRIOV_OFFLOADS). Currently, when in SRIOV, only the
legacy mode is supported, where steering rules are of the form:

        destination mac --> VF vport

This patch does not change any functionality.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the registers of subctrl may be different, it is better to
mv the registers from hns mdio driver routine to device tree node.
Signed-off-by: NKejian Yan <yankejian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is PORT_TP type if the service port is GE mode. It is wrong to
judge the port type by using if it is service port. Adding the media
type to know port type.
Reported-by: NJinchuan Tian <tianjinchuan1@huawei.com>
Signed-off-by: NKejian Yan <yankejian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sequence of hns_mac_dev_to_enet_if() is the same as
hns_get_enet_interface(), and hns_get_enet_interface() is called
by initialization to get the mac mode. And the mode is not changed
anywhere. Thus add hns_mac_dev_to_enet_if() function to get the mac
mode is obviously redundant.
Reported-by: NJinchuan Tian <tianjinchuan1@huawei.com>
Signed-off-by: NKejian Yan <yankejian@huawei.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two approaches to assign data, one does 2 loops, another
does 1 loop. This patch normalize the different methods to 1 loop.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In comment line, some time miss a space before */, so this
patch adds a space before */.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the previous review comments from Andy, this patch
deletes the redundant parens in the patch.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the code style in hns driver. Change it from
"buff = buff + xxx" to "buff += xxx". The reveiw comments is
from andy.
Reviewed-by: NAndriy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes code sytle of hns driver to make it
simple.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NYisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManish <manish.chopra@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch uses xmit_more optimization to reduce
number of TX doorbells write per packet.
Signed-off-by: NManish <manish.chopra@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleanups qede_poll() routine a bit
and allows qede_poll() to do single iteration to handle
TX completion [As under heavy TX load qede_poll() might
run for indefinite time in the while(1) loop for TX
completion processing and cause CPU stuck].
Signed-off-by: NManish <manish.chopra@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>