Basic house keeping: If there is an error adding the router MAC for this
vlan, removing the just installed VLAN table entry to leave device in same
state as before failure.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When allocating the array of rocker port pointers, zero the array values so
we can test for !NULL to see if port is allocated/registered.  We'll need
this later when installing untagged VLAN support for each port, during port
probe.  It's a long story, but to install a VLAN (vid=0 for untagged, in
this case) on a port, we'll need to scan other ports to see if the VLAN
group for that VLAN has been setup.  To scan the other ports, we need to
walk the port array.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently packets with non-hardware-accelerated vlan cannot be handled
by GRO. This causes low performance for 802.1ad and stacked vlan, as their
vlan tags are currently not stripped by hardware.

This patch adds GRO support for non-hardware-accelerated vlan and
improves receive performance of them.

Test Environment:
 vlan device (.1Q) on vlan device (.1ad) on ixgbe (82599)

Result:

- Before

$ netperf -t TCP_STREAM -H 192.168.20.2 -l 60
Recv   Send    Send
Socket Socket  Message  Elapsed
Size   Size    Size     Time     Throughput
bytes  bytes   bytes    secs.    10^6bits/sec

 87380  16384  16384    60.00    5233.17

Rx side CPU usage:
  %usr      %sys      %irq     %soft     %idle
  0.27     58.03      0.00     41.70      0.00

- After

$ netperf -t TCP_STREAM -H 192.168.20.2 -l 60
Recv   Send    Send
Socket Socket  Message  Elapsed
Size   Size    Size     Time     Throughput
bytes  bytes   bytes    secs.    10^6bits/sec

 87380  16384  16384    60.00    7586.85

Rx side CPU usage:
  %usr      %sys      %irq     %soft     %idle
  0.50     25.83      0.00     59.53     14.14

[ Register VLAN offloads with priority 10 -DaveM ]
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unused function cxgb4_enable_db_coalescing() and
cxgb4_disable_db_coalescing()
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rocker (switch) of a rocker_port may be trivially obtained from
the latter it seems cleaner not to pass the former to a function when
the latter is being passed anyway.

rocker_port_rx_proc() is omitted from this change as it is a hot path case.
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Acked-by: NScott Feldman <sfeldma@gmail.com>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver allocates one page for each buffer on the rx ring, which is
too much on architectures like ppc64 and can cause unexpected allocation
failures when the system is under stress.  Now, we keep a memory pool
per queue, and if the architecture's PAGE_SIZE is greater than 4k, we
fragment pages and assign each 4k segment to a ring element, which
reduces the overall memory consumption on such architectures.  This
helps avoiding errors like the example below:

[bnx2x_alloc_rx_sge:435(eth1)]Can't alloc sge
[c00000037ffeb900] [d000000075eddeb4] .bnx2x_alloc_rx_sge+0x44/0x200 [bnx2x]
[c00000037ffeb9b0] [d000000075ee0b34] .bnx2x_fill_frag_skb+0x1ac/0x460 [bnx2x]
[c00000037ffebac0] [d000000075ee11f0] .bnx2x_tpa_stop+0x160/0x2e8 [bnx2x]
[c00000037ffebb90] [d000000075ee1560] .bnx2x_rx_int+0x1e8/0xc30 [bnx2x]
[c00000037ffebcd0] [d000000075ee2084] .bnx2x_poll+0xdc/0x3d8 [bnx2x] (unreliable)
Signed-off-by: NGabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Reviewed-by: NLino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If new optional attribute OVS_USERSPACE_ATTR_ACTIONS is added to an
OVS_ACTION_ATTR_USERSPACE action, then include the datapath actions
in the upcall.

This Directly associates the sampled packet with the path it takes
through the virtual switch. Path information currently includes mangling,
encapsulation and decapsulation actions for tunneling protocols GRE,
VXLAN, Geneve, MPLS and QinQ, but this extension requires no further
changes to accommodate datapath actions that may be added in the
future.

Adding path information enhances visibility into complex virtual
networks.
Signed-off-by: NNeil McKee <neil.mckee@inmon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we scan a packet for GRO processing, we want to see the most
common packet types in the front of the offload_base list.

So add a priority field so we can handle this properly.

IPv4/IPv6 get the highest priority with the implicit zero priority
field.

Next comes ethernet with a priority of 10, and then we have the MPLS
types with a priority of 15.
Suggested-by: NEric Dumazet <eric.dumazet@gmail.com>
Suggested-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.

A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:

@change@
expression e, func, da;
@@

-init_timer (&e);
+setup_timer (&e, func, da);
-e.data = da;
-e.function = func;
Signed-off-by: NVaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sowmini Varadhan says:

====================
net/rds: SOL_RDS socket option to explicitly select transport

Today the underlying transport (TCP or IB) for a PF_RDS socket is
implicitly selected based on the local address used to bind(2) the
PF_RDS socket. This results in some non-deterministic behavior when
there are un-numbered and IPoIB interfaces sharing the same IP address.
It also places the constraint that the IB interface must have an IP
address (and thus, IPoIB) configured on it.

The non-determinism may be avoided by providing the user-space application
a socket option that allows it to explicitly select the transport
prior to bind(2).

Patch 1 of this series provides the constant definitions needed by
the application via <linux/rds.h>.

Patch 2 provides the setsockopt support, and Patch 3 provides the
getsockopt support.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The currently attached transport for a PF_RDS socket may be obtained
from user space by invoking getsockopt(2) using the SO_RDS_TRANSPORT
option at the SOL_RDS level. The integer optval returned will be one
of the RDS_TRANS_* constants defined in linux/rds.h.
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An application may deterministically attach the underlying transport for
a PF_RDS socket by invoking setsockopt(2) with the SO_RDS_TRANSPORT
option at the SOL_RDS level. The integer argument to setsockopt must be
one of the RDS_TRANS_* transport types, e.g., RDS_TRANS_TCP. The option
must be specified before invoking bind(2) on the socket, and may only
be used once on the socket. An attempt to set the option on a bound
socket, or to invoke the option after a successful SO_RDS_TRANSPORT
attachment, will return EOPNOTSUPP.
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

User space applications that desire to explicitly select the
underlying transport for a PF_RDS socket may do so by using the
SO_RDS_TRANSPORT socket option at the SOL_RDS level before bind().
The integer argument provided to the socket option would be one
of the RDS_TRANS_* values, e.g., RDS_TRANS_TCP. This commit exports
the constant values need by such applications via <linux/rds.h>
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.

A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:

@change@
expression e1, e2, e3, e4, a, b;
@@

-init_timer(&e1);
+setup_timer(&e1, a, b);

... when != a = e2
    when != b = e3

-e1.function = a;
... when != b = e4
-e1.data = b;
Signed-off-by: NVaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Besides others, move bpf_tail_call_proto to the remaining definitions
of other protos, improve comments a bit (i.e. remove some obvious ones,
where the code is already self-documenting, add objectives for others),
simplify bpf_prog_array_compatible() a bit.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As this is already exported from tracing side via commit d9847d31
("tracing: Allow BPF programs to call bpf_ktime_get_ns()"), we might
as well want to move it to the core, so also networking users can make
use of it, e.g. to measure diffs for certain flows from ingress/egress.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.

A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:

@change@
expression e1, e2, e3, e4, a, b;
@@

-init_timer(&e1);
+setup_timer(&e1, a, b);

... when != a = e2
    when != b = e3

-e1.data = b;
... when != a = e4
-e1.function = a;
Signed-off-by: NVaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.

A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:

@change@
expression e1, e2, e3, e4, a, b;
@@

-init_timer(&e1);
+setup_timer(&e1, a, b);

... when != a = e2
    when != b = e3

-e1.data = b;
... when != a = e4
-e1.function = a;
Signed-off-by: NVaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.

A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:

@change@
expression e, func, da;
@@

-init_timer (&e);
+setup_timer (&e, func, da);
-e.data = da;
-e.function = func;
Signed-off-by: NVaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2015-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
As we get closer to the merge window, here are a few
more things for -next:
 * disconnect TDLS stations on CSA to avoid issues
 * fix a memory leak introduced in a recent commit
 * switch rfkill and cfg80211 to PM ops
 * in an unlikely scenario, prevent a bookkeeping
   value to get corrupted leading to dropped packets
 * fix a crash in VLAN assignment
 * switch rfkill-gpio to more modern gpiod API
 * send disconnected event to userspace with proper
   local/remote indication
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Antonio Quartulli says:

====================
Included changes:
- checkpatch fixes
- code cleanup
- debugfs component is now compiled only if DEBUG_FS is selected
- update copyright years
- disable by default not-so-user-safe features
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Normally the program attachment place (like sockets, qdiscs) takes
care of rcu protection and calls bpf_prog_put() after a grace period.
The programs stored inside prog_array may not be attached anywhere,
so prog_array needs to take care of preserving rcu protection.
Otherwise bpf_tail_call() will race with bpf_prog_put().
To solve that introduce bpf_prog_put_rcu() helper function and use
it in 3 places where unattached program can decrement refcnt:
closing program fd, deleting/replacing program in prog_array.

Fixes: 04fd61ab ("bpf: allow bpf programs to tail-call other bpf programs")
Reported-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

K. Y. Srinivasan says:

====================
hv_netvsc: Implement NUMA aware memory allocation

Allocate both receive buffer and send buffer from the NUMA node assigned to the
primary channel.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate the send buffer in a NUMA aware way.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate the receive bufer from the NUMA node assigned to the primary
channel.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove automatic variable 'err' in register_netevent_notifier() and
return the result of atomic_notifier_chain_register() directly.
Signed-off-by: NWang Long <long.wanglong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains Netfilter updates for net-next, they are:

1) default CONFIG_NETFILTER_INGRESS to y for easier compile-testing of all
   options.

2) Allow to bind a table to net_device. This introduces the internal
   NFT_AF_NEEDS_DEV flag to perform a mandatory check for this binding.
   This is required by the next patch.

3) Add the 'netdev' table family, this new table allows you to create ingress
   filter basechains. This provides access to the existing nf_tables features
   from ingress.

4) Kill unused argument from compat_find_calc_{match,target} in ip_tables
   and ip6_tables, from Florian Westphal.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: systemport: misc improvements

These patches are highly inspired by changes from Petri on bcmgenet, last patch
is a misc fix that I had pending for a while, but is not a candidate for 'net'
at this point.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Occasionnaly we may get oversized packets from the hardware which exceed
the nomimal 2KiB buffer size we allocate SKBs with. Add an early check
which drops the packet to avoid invoking skb_over_panic() and move on to
processing the next packet.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, bcm_sysport_desc_rx() calls bcm_sysport_rx_refill() at the end of Rx
packet processing loop, after the current Rx packet has already been passed to
napi_gro_receive(). However, bcm_sysport_rx_refill() might fail to allocate a new
Rx skb, thus leaving a hole on the Rx queue where no valid Rx buffer exists.

To eliminate this situation:

1. Rewrite bcm_sysport_rx_refill() to retain the current Rx skb on the
Rx queue if a new replacement Rx skb can't be allocated and DMA-mapped.
In this case, the data on the current Rx skb is effectively dropped.

2. Modify bcm_sysport_desc_rx() to call bcm_sysport_rx_refill() at the
top of Rx packet processing loop, so that the new replacement Rx skb is
already in place before the current Rx skb is processed.

This is loosely inspired from d6707bec ("net: bcmgenet: rewrite
bcmgenet_rx_refill()")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a 1:1 mapping between the software maintained control block in
priv->rx_cbs and the buffer address in priv->rx_bds, such that there is
no need to keep computing the buffer address when refiling a control
block.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delete jump to a label on the next line, when that label is not
used elsewhere.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier l;
@@

-if (...) goto l;
-l:
// </smpl>

Also remove the unnecessary ret variable.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The thunderx ethernet driver fails to build on architectures
that do not have an atomic readq() and writeq() function for
64-bit PCI bus access:

drivers/net/ethernet/cavium/thunder/thunder_bgx.c: In function 'bgx_reg_read':
include/asm-generic/io.h:195:23: error: implicit declaration of function 'readq' [-Werror=implicit-function-declaration]

It seems impossible to get this driver to work on most 32-bit
hardware, so it's better to add an explicit dependency, in
order to let us keep building 'allmodconfig' kernels on
all architectures.

As the driver is meant for the internal hardware on an arm64 SoC, this
is not a problem for usability. Allowing the build on all 64-bit
architectures rather than just CONFIG_ARM64 on the other hand means that
we get the benefit of build testing on x86.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4 driver update, May 28, 2015

The 1st patch fixes an issue with a function running DPDK overriding
broadcast steering rules set by other functions. Please add this one
to your -stable queue.

The rest of the series from Matan and Ido deals with scaling the number
of IRQs that serve RoCE applications to be in par with the Ethernet driver.

changes from V0:
 - addressed feedback from Sergei, removed extra blank line in patch #4
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When freeing a CQ, we need to make sure there are no
asynchronous events (on the ASYNC EQ) that could
relate to this CQ before freeing it.

This is done by introducing synchronize_irq.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that EQs management is in the sole responsibility of mlx4_core,
the IRQ affinity hints configuration should be in its hands as well.
request_irq is called only once by the first consumer (maybe mlx4_ib),
so mlx4_en passes the affinity mask too late. We also need to request
vectors according to the cores we want to run on.

mlx4_core distribution of IRQs to cores is straight forward,
EQ(i)->IRQ will set affinity hint to core i.
Consumers need to request EQ vectors, according to their cores
considerations (NUMA).
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, mlx4_en allocated EQs and used them exclusively.
This affected RoCE performance, as applications which are
events sensitive were limited to use only the legacy EQs.

Change that by introducing an EQ pool. This pool is managed
by mlx4_core. EQs are assigned to ports (when there are limited
number of EQs, multiple ports could be assigned to the same EQs).

An exception to this rule is the ASYNC EQ which handles various events.

Legacy EQs are completely removed as all EQs could be shared.

When a consumer (mlx4_ib/mlx4_en) requests an EQ, it asks for
EQ serving on a specific port. The core driver calculates which
EQ should be assigned to that request.

Because IRQs are shared between IB and Ethernet modules, their
names only include the PCI device BDF address.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In SRIOV, when simple (i.e - Ethernet L2 only) flow steering rules are
created, always create them at MLX4_DOMAIN_NIC priority (instead of
the real priority the function created them at). This is done in order
to let multiple functions add broadcast/multicast rules without
affecting other functions, which is necessary for DPDK in SRIOV.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2015-05-28

Here's a set of patches intended for 4.2. The majority of the changes
are on the 802.15.4 side of things rather than Bluetooth related:

 - All sorts of cleanups & fixes to ieee802154 and related drivers
 - Rework of tx power support in ieee802154 and its drivers
 - Support for setting ieee802154 tx power through nl802154
 - New IDs for the btusb driver
 - Various cleanups & smaller fixes to btusb
 - New btrtl driver for Realtec devices
 - Fix suspend/resume for Realtek devices

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Amir Vadai says:

====================
net/mlx5: ConnectX-4 100G Ethernet driver

This patchset extends the mlx5_core driver to support Ethernet
functionality. The Ethernet functionality in the mlx5 driver is
integrated into the core driver and not as separated driver. The
IB functionality remains in the mlx5_ib driver as before.

This functionality will enable the Ethernet capability of Mellanox's new
famility of cards - ConnectX-4. Due to the fact that backword
compatability is being kept, existing Connect-IB cards that are using
this driver are fully working with the modified driver, and no issues
with current deployments should be seen.

Like the ConnectX-3 cards, ConnectX-4 is a VPI (Virtual Port Interface -
every port can be configured as Infiniband or Ethernet) card.
Unlike previous generations, the ConnectX-4 has a separate PCI function
per port.

The current code has a limitation that Infiniband and Ethernet port types
are mutually exclusive. When the driver is compiled with Ethernet
support, the Infiniband functionality is disabled and vice versa. To
control that we added the CONFIG_MLX5_CORE_EN config directive
which is 'n' by default, but can be changed by the user.

This limitation is short-lived and would be addressed soon.

As part of this patchset, mlx5_ifc.h was heavily modified [1]. This file
is now generated automatically from the device specification document.
Since this patch is too big for the mail server, it might be missing in
the mailing list, but could be pulled from an external git repository [2].

irq name selection is done at driver initialization and doesn't contain the
interface name as part of the irq name.
irq_balancer will still work thanks to an improvement introduced by Neil Horman
[3] to use sysfs instead of /proc/interrupts.

Patchset was applied on top of commit ed2dfd90 ("tcp/dccp: warn user for
preferred ip_local_port_range")

[1] - Patch 4/11 ("net/mlx5_core: HW data structs/types definitions preparation for mlx5 ehternet driver")
[2] - http://git.openfabrics.org/?p=~amirv/linux.git;a=shortlog;h=refs/heads/mlx5e_v1
[3] - kernel: da8d1c8b PCI/sysfs: add per pci device msi[x] irq listing (v5)
      irq_balancer: 32a7757 Complete rework of how we detect and classify irqs

Thanks to Achiad, Saeed, Yevheny, Or and the whole team for making this happen,
Amir

Changes from V4:
- Removed Patch 3/12: net/mlx5_core: Add EQ renaming mechanism
- Patch 12/12: net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality
  - irq name is created on driver initialization, therefore it won't contain
    the network interface name in it. This won't effect irq_balancer thanks to
    patches introduced by Neil Horman to use sysfs instead of /proc/interrupts.

Changes from V3:
- PATCH 8/11: net/mlx5_core: Set/Query port MTU commands
  - Return value directly - no need for err.

Changes from V2:
- Improved changelogs and cover-letter
- Added CONFIG_MLX5_EN to disable/enable the Ethernet functionality
- Moved en.h and wq.[ch] into the patch with data-path related code

Changes from V1:
- Added patch 1/12 ("net/mlx5_core,mlx5_ib: Do not use vmap() on coherent
  memory")

Changes from V0:
- Removed V0 Patch 1/11 ("net/mlx5_core: Virtually extend work/completion queue
  buffers by one page") due to misuse of DMA API. Thanks Dave.
- Patch 1/11 ("net/mlx5_core: Set irq affinity hints"):
  - Use kcalloc instead of kzalloc
  - Fix build error when CONFIG_CPUMASK_OFFSTACK=n. Driver loading will fail
    now if cpumask allocation is failing.
  - Using dev_to_node helper. Thanks, Ido.
- Patch 3/11 ("net/mlx5_core: HW data structs/types definitions preparation for
  mlx5 ehternet driver")
  - Removed Mellanox internal comment at the head of the file. Thanks Joe
- Patch 6/11 ("net/mlx5_core: Implement get/set port status")
  - Use direct return of function's result. Thanks Sergei.
- Added Patch 8/11 ("net/mlx5_core: Set/Query port MTU commands")
- Patch 9/11 ("net/mlx5: Ethernet Datapath files")
  - Use rq->wqe_sz instead of skb_end_offset. Thanks Ido.
  - Use dma_wmb() when possible instead of wmb(). Thanks Alex.
  - Fix checkpatch issues
- Patch 10/11 ("net/mlx5: ethernet resources handling")
  - checkpatch issues
  - Added missing include
- Patch 11/11 ("net/mlx5: Ethernet driver")
  - checkpatch issues
  - fixed typo
  - Modified use of affinity hint
  - Using dev_to_node helper. Thanks, Ido.
  - Use new hardware commands from Patch 8/11 ("net/mlx5_core: Set/Query port
    MTU commands") to get/set port MTU in hardware.
  - Removed NETIF_F_SG since hardware ring wraparound is not supported
  - Use dma_wmb() when possible instead of wmb(). Thanks Alex.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>