commit 1186f86a71130a7635a20843e355bb880c7349b2 upstream.

Commit 3ae62a42090f ("UAS: fix alignment of scatter/gather segments"),
copying a similar commit for usb-storage, attempted to solve a problem
involving scatter-gather I/O and USB/IP by setting the
virt_boundary_mask for mass-storage devices.

However, it now turns out that the analogous change in usb-storage
interacted badly with commit 09324d32d2a0 ("block: force an unlimited
segment size on queues with a virt boundary"), which was added later.
A typical error message is:

	ehci-pci 0000:00:13.2: swiotlb buffer is full (sz: 327680 bytes),
	total 32768 (slots), used 97 (slots)

There is no longer any reason to keep the virt_boundary_mask setting
in the uas driver.  It was needed in the first place only for
handling devices with a block size smaller than the maxpacket size and
where the host controller was not capable of fully general
scatter-gather operation (that is, able to merge two SG segments into
a single USB packet).  But:

	High-speed or slower connections never use a bulk maxpacket
	value larger than 512;

	The SCSI layer does not handle block devices with a block size
	smaller than 512 bytes;

	All the host controllers capable of SuperSpeed operation can
	handle fully general SG;

	Since commit ea44d190764b ("usbip: Implement SG support to
	vhci-hcd and stub driver") was merged, the USB/IP driver can
	also handle SG.

Therefore all supported device/controller combinations should be okay
with no need for any special virt_boundary_mask.  So in order to head
off potential problems similar to those affecting usb-storage, this
patch reverts commit 3ae62a42090f.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Acked-by: NChristoph Hellwig <hch@lst.de>
Fixes: 3ae62a42090f ("UAS: fix alignment of scatter/gather segments")
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910231132470.1878-100000@iolanthe.rowland.orgSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f0778871a13889b86a65d4ad34bef8340af9d082 upstream.

Support new codec ALC623.
Signed-off-by: NKailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/ed97b6a8bd9445ecb48bc763d9aaba7a@realtek.comSigned-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8a6c55d0f883e9a7e7c91841434f3b6bbf932bb2 upstream.

These 2 ThinkCentres installed a new realtek codec ID 0x623,
it has 2 front mics with the same location on pin 0x18 and 0x19.

Apply fixup ALC283_FIXUP_HEADSET_MIC to change 1 front mic
location to right, then pulseaudio can handle them.
One "Front Mic" and one "Mic" will be shown, and audio output works
fine.
Signed-off-by: NAaron Ma <aaron.ma@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191024114439.31522-1-aaron.ma@canonical.comSigned-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f2bbdbcb075f3977a53da3bdcb7cd460bc8ae5f2 upstream.

A helper function of ALSA bebob driver returns negative value in a
function which has a prototype to return unsigned value.

This commit fixes it by changing the prototype.

Fixes: eb7b3a05 ("ALSA: bebob: Add commands and connections/streams management")
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191026030620.12077-1-o-takashi@sakamocchi.jpSigned-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e4648309b85a78f8c787457832269a8712a8673e upstream.

Make sure cached writes are not reordered around open(..., O_TRUNC), with
the obvious wrong results.

Fixes: 4d99ff8f ("fuse: Turn writeback cache on")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: NMiklos Szeredi <mszeredi@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b24e7598db62386a95a3c8b9c75630c5d56fe077 upstream.

If writeback cache is enabled, then writes might get reordered with
chmod/chown/utimes.  The problem with this is that performing the write in
the fuse daemon might itself change some of these attributes.  In such case
the following sequence of operations will result in file ending up with the
wrong mode, for example:

  int fd = open ("suid", O_WRONLY|O_CREAT|O_EXCL);
  write (fd, "1", 1);
  fchown (fd, 0, 0);
  fchmod (fd, 04755);
  close (fd);

This patch fixes this by flushing pending writes before performing
chown/chmod/utimes.
Reported-by: NGiuseppe Scrivano <gscrivan@redhat.com>
Tested-by: NGiuseppe Scrivano <gscrivan@redhat.com>
Fixes: 4d99ff8f ("fuse: Turn writeback cache on")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: NMiklos Szeredi <mszeredi@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 39d170b3cb62ba98567f5c4f40c27b5864b304e5 ]

The `ar_usb` field of `ath6kl_usb_pipe_usb_pipe` objects
are initialized to point to the containing `ath6kl_usb` object
according to endpoint descriptors read from the device side, as shown
below in `ath6kl_usb_setup_pipe_resources`:

for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
	endpoint = &iface_desc->endpoint[i].desc;

	// get the address from endpoint descriptor
	pipe_num = ath6kl_usb_get_logical_pipe_num(ar_usb,
						endpoint->bEndpointAddress,
						&urbcount);
	......
	// select the pipe object
	pipe = &ar_usb->pipes[pipe_num];

	// initialize the ar_usb field
	pipe->ar_usb = ar_usb;
}

The driver assumes that the addresses reported in endpoint
descriptors from device side  to be complete. If a device is
malicious and does not report complete addresses, it may trigger
NULL-ptr-deref `ath6kl_usb_alloc_urb_from_pipe` and
`ath6kl_usb_free_urb_to_pipe`.

This patch fixes the bug by preventing potential NULL-ptr-deref
(CVE-2019-15098).
Signed-off-by: NHui Peng <benquike@gmail.com>
Reported-by: NHui Peng <benquike@gmail.com>
Reported-by: NMathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 943795219d3cb9f8ce6ce51cad3ffe1f61e95c6b ]

The register access should be using 32-bit reads/writes according to the
datasheet. With the previous generation hardware 16-bit writes have been
working but starting with ICL this is not the case anymore so fix
producer/consumer register update to use correct width register address.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NYehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: NMario Limonciello <mario.limonciello@dell.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit fd47a417e75e2506eb3672ae569b1c87e3774155 ]

The problem is that sizeof() is unsigned long so negative error codes
are type promoted to high positive values and the condition becomes
false.

Fixes: 1d427be4a39d ("USB: legousbtower: fix slab info leak at probe")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NJohan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191011141115.GA4521@mwandaSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit cf1b2326b734896734c6e167e41766f9cee7686a ]

nbd requires socket families to support the shutdown method so the nbd
recv workqueue can be woken up from its sock_recvmsg call. If the socket
does not support the callout we will leave recv works running or get hangs
later when the device or module is removed.

This adds a check during socket connection/reconnection to make sure the
socket being passed in supports the needed callout.

Reported-by: syzbot+24c12fa8d218ed26011a@syzkaller.appspotmail.com
Fixes: e9e006f5fcf2 ("nbd: fix max number of supported devs")
Tested-by: NRichard W.M. Jones <rjones@redhat.com>
Signed-off-by: NMike Christie <mchristi@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 12e36d98d3e5acf5fc57774e0a15906d55f30cb9 ]

We currently support two NICs in FW version 29, namely 7265D and 3168.
Out of these, only 7265D supports GEO SAR, so adjust the function that
checks for it accordingly.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Fixes: f5a47fae6aa3 ("iwlwifi: mvm: fix version check for GEO_TX_POWER_LIMIT support")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 1099f48457d06b816359fb43ac32a4a07e33219b ]

Headphone on XPS 9350/9360 produces a background white noise. The The
noise level somehow correlates with "Headphone Mic Boost", when it sets
to 1 the noise disappears. However, doing this has a side effect, which
also decreases the overall headphone volume so I didn't send the patch
upstream.

The noise was bearable back then, but after commit 717f43d81afc ("ALSA:
hda/realtek - Update headset mode for ALC256") the noise exacerbates to
a point it starts hurting ears.

So let's use the workaround to set "Headphone Mic Boost" to 1 and lock
it so it's not touchable by userspace.

Fixes: 717f43d81afc ("ALSA: hda/realtek - Update headset mode for ALC256")
BugLink: https://bugs.launchpad.net/bugs/1654448
BugLink: https://bugs.launchpad.net/bugs/1845810Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20191003043919.10960-1-kai.heng.feng@canonical.comSigned-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4c0742f65b4ee466546fd24b71b56516cacd4613 ]

It was reported that 72cd4064fcca "NOMMU: Toggle only bits in
EXC_RETURN we are really care of" breaks NOMMU+XIP combination.
It happens because saved EXC_RETURN gets overwritten when data
section is relocated.

The fix is to propagate EXC_RETURN via register and let relocation
code to commit that value into memory.

Fixes: 72cd4064fcca ("ARM: 8830/1: NOMMU: Toggle only bits in EXC_RETURN we are really care of")
Reported-by: Nafzal mohammed <afzal.mohd.ma@gmail.com>
Tested-by: Nafzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: NVladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit d303de1fcf344ff7c15ed64c3f48a991c9958775 ]

A customer reported the following softlockup:

[899688.160002] NMI watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [test.sh:16464]
[899688.160002] CPU: 0 PID: 16464 Comm: test.sh Not tainted 4.12.14-6.23-azure #1 SLE12-SP4
[899688.160002] RIP: 0010:up_write+0x1a/0x30
[899688.160002] Kernel panic - not syncing: softlockup: hung tasks
[899688.160002] RIP: 0010:up_write+0x1a/0x30
[899688.160002] RSP: 0018:ffffa86784d4fde8 EFLAGS: 00000257 ORIG_RAX: ffffffffffffff12
[899688.160002] RAX: ffffffff970fea00 RBX: 0000000000000001 RCX: 0000000000000000
[899688.160002] RDX: ffffffff00000001 RSI: 0000000000000080 RDI: ffffffff970fea00
[899688.160002] RBP: ffffffffffffffff R08: ffffffffffffffff R09: 0000000000000000
[899688.160002] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8b59014720d8
[899688.160002] R13: ffff8b59014720c0 R14: ffff8b5901471090 R15: ffff8b5901470000
[899688.160002]  tracing_read_pipe+0x336/0x3c0
[899688.160002]  __vfs_read+0x26/0x140
[899688.160002]  vfs_read+0x87/0x130
[899688.160002]  SyS_read+0x42/0x90
[899688.160002]  do_syscall_64+0x74/0x160

It caught the process in the middle of trace_access_unlock(). There is
no loop. So, it must be looping in the caller tracing_read_pipe()
via the "waitagain" label.

Crashdump analyze uncovered that iter->seq was completely zeroed
at this point, including iter->seq.seq.size. It means that
print_trace_line() was never able to print anything and
there was no forward progress.

The culprit seems to be in the code:

	/* reset all but tr, trace, and overruns */
	memset(&iter->seq, 0,
	       sizeof(struct trace_iterator) -
	       offsetof(struct trace_iterator, seq));

It was added by the commit 53d0aa77 ("ftrace:
add logic to record overruns"). It was v2.6.27-rc1.
It was the time when iter->seq looked like:

     struct trace_seq {
	unsigned char		buffer[PAGE_SIZE];
	unsigned int		len;
     };

There was no "size" variable and zeroing was perfectly fine.

The solution is to reinitialize the structure after or without
zeroing.

Link: http://lkml.kernel.org/r/20191011142134.11997-1-pmladek@suse.comSigned-off-by: NPetr Mladek <pmladek@suse.com>
Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 062795fcdcb2d22822fb42644b1d76a8ad8439b3 ]

Depending on inlining decisions by the compiler, __get/put_user_fn
might become out of line. Then the compiler is no longer able to tell
that size can only be 1,2,4 or 8 due to the check in __get/put_user
resulting in false positives like

./arch/s390/include/asm/uaccess.h: In function ‘__put_user_fn’:
./arch/s390/include/asm/uaccess.h:113:9: warning: ‘rc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  113 |  return rc;
      |         ^~
./arch/s390/include/asm/uaccess.h: In function ‘__get_user_fn’:
./arch/s390/include/asm/uaccess.h:143:9: warning: ‘rc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  143 |  return rc;
      |         ^~

These functions are supposed to be always inlined. Mark it as such.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NVasily Gorbik <gor@linux.ibm.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 1047ec868332034d1fbcb2fae19fe6d4cb869ff2 ]

Our client can issue multiple SETCLIENTID operations to the same
server in some circumstances. Ensure that calls to
nfs4_proc_setclientid() after the first one do not overwrite the
previously allocated cl_acceptor string.

unreferenced object 0xffff888461031800 (size 32):
  comm "mount.nfs", pid 2227, jiffies 4294822467 (age 1407.749s)
  hex dump (first 32 bytes):
    6e 66 73 40 6b 6c 69 6d 74 2e 69 62 2e 31 30 31  nfs@klimt.ib.101
    35 67 72 61 6e 67 65 72 2e 6e 65 74 00 00 00 00  5granger.net....
  backtrace:
    [<00000000ab820188>] __kmalloc+0x128/0x176
    [<00000000eeaf4ec8>] gss_stringify_acceptor+0xbd/0x1a7 [auth_rpcgss]
    [<00000000e85e3382>] nfs4_proc_setclientid+0x34e/0x46c [nfsv4]
    [<000000003d9cf1fa>] nfs40_discover_server_trunking+0x7a/0xed [nfsv4]
    [<00000000b81c3787>] nfs4_discover_server_trunking+0x81/0x244 [nfsv4]
    [<000000000801b55f>] nfs4_init_client+0x1b0/0x238 [nfsv4]
    [<00000000977daf7f>] nfs4_set_client+0xfe/0x14d [nfsv4]
    [<0000000053a68a2a>] nfs4_create_server+0x107/0x1db [nfsv4]
    [<0000000088262019>] nfs4_remote_mount+0x2c/0x59 [nfsv4]
    [<00000000e84a2fd0>] legacy_get_tree+0x2d/0x4c
    [<00000000797e947c>] vfs_get_tree+0x20/0xc7
    [<00000000ecabaaa8>] fc_mount+0xe/0x36
    [<00000000f15fafc2>] vfs_kern_mount+0x74/0x8d
    [<00000000a3ff4e26>] nfs_do_root_mount+0x8a/0xa3 [nfsv4]
    [<00000000d1c2b337>] nfs4_try_mount+0x58/0xad [nfsv4]
    [<000000004c9bddee>] nfs_fs_mount+0x820/0x869 [nfs]

Fixes: f11b2a1c ("nfs4: copy acceptor name from context ... ")
Signed-off-by: NChuck Lever <chuck.lever@oracle.com>
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 862488105b84ca744b3d8ff131e0fcfe10644be1 ]

1. nbd_put takes the mutex and drops nbd->ref to 0. It then does
idr_remove and drops the mutex.

2. nbd_genl_connect takes the mutex. idr_find/idr_for_each fails
to find an existing device, so it does nbd_dev_add.

3. just before the nbd_put could call nbd_dev_remove or not finished
totally, but if nbd_dev_add try to add_disk, we can hit:

debugfs: Directory 'nbd1' with parent 'block' already present!

This patch will make sure all the disk add/remove stuff are done
by holding the nbd_index_mutex lock.
Reported-by: NMike Christie <mchristi@redhat.com>
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Signed-off-by: NXiubo Li <xiubli@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e0b0cb9388642c104838fac100a4af32745621e2 ]

In hgcm_call_preprocess_linaddr memory is allocated for bounce_buf but
is not released if copy_form_user fails. In order to prevent memory leak
in case of failure, the assignment to bounce_buf_ret is moved before the
error check. This way the allocated bounce_buf will be released by the
caller.

Fixes: 579db9d4 ("virt: Add vboxguest VMMDEV communication code")
Signed-off-by: NNavid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20190930204223.3660-1-navid.emamdoost@gmail.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit efcb529694c3b707dc0471b312944337ba16e4dd ]

Use ARRAY_SIZE to caluculate the top of the o32 stack.
Signed-off-by: NThomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 46f1619500d022501a4f0389f9f4c349ab46bb86 ]

Commit ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING
forcibly") allows compiler to uninline functions marked as 'inline'.
In cace of __xchg this would cause to reference function
__xchg_called_with_bad_pointer, which is an error case
for catching bugs and will not happen for correct code, if
__xchg is inlined.
Signed-off-by: NThomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: NPhilippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit ab612b1daf415b62c58e130cb3d0f30b255a14d0 ]

In adis_update_scan_mode, if allocation for adis->buffer fails,
previously allocated adis->xfer needs to be released.
Signed-off-by: NNavid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NJonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 083164dbdb17c5ea4ad92c1782b59c9d75567790 ]

cleanup error handling code and make sure temporary info array
with the handles are freed by amdgpu_bo_list_put() on
idr_replace()'s failure.
Signed-off-by: NNirmoy Das <nirmoy.das@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit df4d29732fdad43a51284f826bec3e6ded177540 ]

It turns out that the NMI latency workaround from commit:

  6d3edaae16c6 ("x86/perf/amd: Resolve NMI latency issues for active PMCs")

ends up being too conservative and results in the perf NMI handler claiming
NMIs too easily on AMD hardware when the NMI watchdog is active.

This has an impact, for example, on the hpwdt (HPE watchdog timer) module.
This module can produce an NMI that is used to reset the system. It
registers an NMI handler for the NMI_UNKNOWN type and relies on the fact
that nothing has claimed an NMI so that its handler will be invoked when
the watchdog device produces an NMI. After the referenced commit, the
hpwdt module is unable to process its generated NMI if the NMI watchdog is
active, because the current NMI latency mitigation results in the NMI
being claimed by the perf NMI handler.

Update the AMD perf NMI latency mitigation workaround to, instead, use a
window of time. Whenever a PMC is handled in the perf NMI handler, set a
timestamp which will act as a perf NMI window. Any NMIs arriving within
that window will be claimed by perf. Anything outside that window will
not be claimed by perf. The value for the NMI window is set to 100 msecs.
This is a conservative value that easily covers any NMI latency in the
hardware. While this still results in a window in which the hpwdt module
will not receive its NMI, the window is now much, much smaller.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jerry Hoemann <jerry.hoemann@hpe.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 6d3edaae16c6 ("x86/perf/amd: Resolve NMI latency issues for active PMCs")
Link: https://lkml.kernel.org/r/Message-ID:
Signed-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 68e7a4d66b0ce04bf18ff2ffded5596ab3618585 ]

vtime_account_system() assumes that the target task to account cputime
to is always the current task. This is most often true indeed except on
task switch where we call:

	vtime_common_task_switch(prev)
		vtime_account_system(prev)

Here prev is the scheduling-out task where we account the cputime to. It
doesn't match current that is already the scheduling-in task at this
stage of the context switch.

So we end up checking the wrong task flags to determine if we are
accounting guest or system time to the previous task.

As a result the wrong task is used to check if the target is running in
guest mode. We may then spuriously account or leak either system or
guest time on task switch.

Fix this assumption and also turn vtime_guest_enter/exit() to use the
task passed in parameter as well to avoid future similar issues.
Signed-off-by: NFrederic Weisbecker <frederic@kernel.org>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wanpeng Li <wanpengli@tencent.com>
Fixes: 2a42eb95 ("sched/cputime: Accumulate vtime on top of nsec clocksource")
Link: https://lkml.kernel.org/r/20190925214242.21873-1-frederic@kernel.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8d7c6ac3b2371eb1cbc9925a88f4d10efff374de ]

Comet Lake is the new 10th Gen Intel processor. Add two new CPU model
numbers to the Intel family list.

The CPU model numbers are not published in the SDM yet but they come
from an authoritative internal source.

 [ bp: Touch up commit message. ]
Signed-off-by: NKan Liang <kan.liang@linux.intel.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Reviewed-by: NTony Luck <tony.luck@intel.com>
Cc: ak@linux.intel.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/1570549810-25049-2-git-send-email-kan.liang@linux.intel.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 3e7c93bd04edfb0cae7dad1215544c9350254b8f ]

There are no return value checking when using kzalloc() and kcalloc() for
memory allocation. so add it.
Signed-off-by: NYunfeng Ye <yeyunfeng@huawei.com>
Signed-off-by: NWill Deacon <will@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 2abb7d3b12d007c30193f48bebed781009bebdd2 ]

In ocfs2_info_scan_inode_alloc(), there is an if statement on line 283
to check whether inode_alloc is NULL:

    if (inode_alloc)

When inode_alloc is NULL, it is used on line 287:

    ocfs2_inode_lock(inode_alloc, &bh, 0);
        ocfs2_inode_lock_full_nested(inode, ...)
            struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);

Thus, a possible null-pointer dereference may occur.

To fix this bug, inode_alloc is checked on line 286.

This bug is found by a static analysis tool STCheck written by us.

Link: http://lkml.kernel.org/r/20190726033717.32359-1-baijiaju1990@gmail.comSigned-off-by: NJia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 583fee3e12df0e6f1f66f063b989d8e7fed0e65a ]

In ocfs2_write_end_nolock(), there are an if statement on lines 1976,
2047 and 2058, to check whether handle is NULL:

    if (handle)

When handle is NULL, it is used on line 2045:

	ocfs2_update_inode_fsync_trans(handle, inode, 1);
        oi->i_sync_tid = handle->h_transaction->t_tid;

Thus, a possible null-pointer dereference may occur.

To fix this bug, handle is checked before calling
ocfs2_update_inode_fsync_trans().

This bug is found by a static analysis tool STCheck written by us.

Link: http://lkml.kernel.org/r/20190726033705.32307-1-baijiaju1990@gmail.comSigned-off-by: NJia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 56e94ea132bb5c2c1d0b60a6aeb34dcb7d71a53d ]

In ocfs2_xa_prepare_entry(), there is an if statement on line 2136 to
check whether loc->xl_entry is NULL:

    if (loc->xl_entry)

When loc->xl_entry is NULL, it is used on line 2158:

    ocfs2_xa_add_entry(loc, name_hash);
        loc->xl_entry->xe_name_hash = cpu_to_le32(name_hash);
        loc->xl_entry->xe_name_offset = cpu_to_le16(loc->xl_size);

and line 2164:

    ocfs2_xa_add_namevalue(loc, xi);
        loc->xl_entry->xe_value_size = cpu_to_le64(xi->xi_value_len);
        loc->xl_entry->xe_name_len = xi->xi_name_len;

Thus, possible null-pointer dereferences may occur.

To fix these bugs, if loc-xl_entry is NULL, ocfs2_xa_prepare_entry()
abnormally returns with -EINVAL.

These bugs are found by a static analysis tool STCheck written by us.

[akpm@linux-foundation.org: remove now-unused ocfs2_xa_add_entry()]
Link: http://lkml.kernel.org/r/20190726101447.9153-1-baijiaju1990@gmail.comSigned-off-by: NJia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 7a243c82ea527cd1da47381ad9cd646844f3b693 ]

Unused portion of a part-written fs-block-sized block is not set to zero
in unaligned append direct write.This can lead to serious data
inconsistencies.

Ocfs2 manage disk with cluster size(for example, 1M), part-written in
one cluster will change the cluster state from UN-WRITTEN to WRITTEN,
VFS(function dio_zero_block) doesn't do the cleaning because bh's state
is not set to NEW in function ocfs2_dio_wr_get_block when we write a
WRITTEN cluster.  For example, the cluster size is 1M, file size is 8k
and we direct write from 14k to 15k, then 12k~14k and 15k~16k will
contain dirty data.

We have to deal with two cases:
 1.The starting position of direct write is outside the file.
 2.The starting position of direct write is located in the file.

We need set bh's state to NEW in the first case.  In the second case, we
need mapped twice because bh's state of area out file should be set to
NEW while area in file not.

[akpm@linux-foundation.org: coding style fixes]
Link: http://lkml.kernel.org/r/5292e287-8f1a-fd4a-1a14-661e555e0bed@huawei.comSigned-off-by: NJia Guo <guojia12@huawei.com>
Reviewed-by: NYiwen Jiang <jiangyiwen@huawei.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c6875f3aacf2a5a913205accddabf0bfb75cac76 ]

Currently execution of panic() continues until Xen's panic notifier
(xen_panic_event()) is called at which point we make a hypercall that
never returns.

This means that any notifier that is supposed to be called later as
well as significant part of panic() code (such as pstore writes from
kmsg_dump()) is never executed.

There is no reason for xen_panic_event() to be this last point in
execution since panic()'s emergency_restart() will call into
xen_emergency_restart() from where we can perform our hypercall.

Nevertheless, we will provide xen_legacy_crash boot option that will
preserve original behavior during crash. This option could be used,
for example, if running kernel dumper (which happens after panic
notifiers) is undesirable.
Reported-by: NJames Dingwall <james@dingwall.me.uk>
Signed-off-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 88356d09904bc606182c625575237269aeece22e ]

Commit ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING
forcibly") allows compiler to uninline functions marked as 'inline'.
In cace of cmpxchg this would cause to reference function
__cmpxchg_called_with_bad_pointer, which is a error case
for catching bugs and will not happen for correct code, if
__cmpxchg is inlined.
Signed-off-by: NThomas Bogendoerfer <tbogendoerfer@suse.de>
[paul.burton@mips.com: s/__cmpxchd/__cmpxchg in subject]
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 2ecb7402cfc7f22764e7bbc80790e66eadb20560 ]

kexec reboot fails randomly in UEFI based KVM guest.  The firmware
just resets while calling efi_delete_dummy_variable();  Unfortunately
I don't know how to debug the firmware, it is also possible a potential
problem on real hardware as well although nobody reproduced it.

The intention of the efi_delete_dummy_variable is to trigger garbage collection
when entering virtual mode.  But SetVirtualAddressMap can only run once
for each physical reboot, thus kexec_enter_virtual_mode() is not necessarily
a good place to clean a dummy object.

Drop the efi_delete_dummy_variable so that kexec reboot can work.
Signed-off-by: NDave Young <dyoung@redhat.com>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: NMatthew Garrett <mjg59@google.com>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Scott Talbert <swt@techie.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Cc: linux-integrity@vger.kernel.org
Link: https://lkml.kernel.org/r/20191002165904.8819-8-ard.biesheuvel@linaro.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 6fb9367a15d1a126d222d738b2702c7958594a5f ]

The CPER parser assumes that the class code is big endian, but at least
on this edk2-derived Intel Purley platform it's little endian:

    efi: EFI v2.50 by EDK II BIOS ID:PLYDCRB1.86B.0119.R05.1701181843
    DMI: Intel Corporation PURLEY/PURLEY, BIOS PLYDCRB1.86B.0119.R05.1701181843 01/18/2017

    {1}[Hardware Error]:   device_id: 0000:5d:00.0
    {1}[Hardware Error]:   slot: 0
    {1}[Hardware Error]:   secondary_bus: 0x5e
    {1}[Hardware Error]:   vendor_id: 0x8086, device_id: 0x2030
    {1}[Hardware Error]:   class_code: 000406
                                       ^^^^^^ (should be 060400)
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Dave Young <dyoung@redhat.com>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Matthew Garrett <mjg59@google.com>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Scott Talbert <swt@techie.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Cc: linux-integrity@vger.kernel.org
Link: https://lkml.kernel.org/r/20191002165904.8819-2-ard.biesheuvel@linaro.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 37e3ab00e4734acc15d96b2926aab55c894f4d9c ]

When using mctrl_gpio_to_gpiod, it dereferences gpios into a single
requested GPIO.  This dereferencing can break if gpios is NULL,
so this patch adds a NULL check before dereferencing it.  If
gpios is NULL, this function will also return NULL.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Reviewed-by: NYegor Yefremov <yegorslists@googlemail.com>
Link: https://lore.kernel.org/r/20191006163314.23191-1-aford173@gmail.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit dd19c106a36690b47bb1acc68372f2b472b495b8 ]

After 'Initial git repository build' commit,
'mapping_table_ERRHRD' variable has not been used.

So 'mapping_table_ERRHRD' const variable could be removed
to mute below warning message:

   fs/cifs/netmisc.c:120:40: warning: unused variable 'mapping_table_ERRHRD' [-Wunused-const-variable]
   static const struct smb_to_posix_error mapping_table_ERRHRD[] = {
                                           ^
Signed-off-by: NAustin Kim <austindh.kim@gmail.com>
Signed-off-by: NSteve French <stfrench@microsoft.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit fffa6af94894126994a7600c6f6f09b892e89fa9 ]

The gpiod_set_debounce() function takes the debounce time in
microseconds. Adjust the switch/case values in the MAX77620 GPIO to use
the correct unit.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191002122825.3948322-1-thierry.reding@gmail.comSigned-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 47a7e5e97d4edd7b14974d34f0e5a5560fad2915 ]

Fix tty driver build on SPARC by not using __exitdata.
It appears that SPARC does not support section .exit.data.

Fixes these build errors:

`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
Reported-by: Nkbuild test robot <lkp@intel.com>
Fixes: 06324664 ("format-security: move static strings to const")
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/r/675e7bd9-955b-3ff3-1101-a973b58b5b75@infradead.orgSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 6264dab6efd6069f0387efb078a9960b5642377b ]

'exit' functions should be marked as __exit, not __init.

Fixes: fc60a8b6 ("tty: serial: owl: Implement console driver")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20190910041129.6978-1-christophe.jaillet@wanadoo.frSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit dd8a1f13488438c6c220b7cafa500baaf21a6e53 ]

CPUs affected by Neoverse-N1 #1542419 may execute a stale instruction if
it was recently modified. The affected sequence requires freshly written
instructions to be executable before a branch to them is updated.

There are very few places in the kernel that modify executable text,
all but one come with sufficient synchronisation:
 * The module loader's flush_module_icache() calls flush_icache_range(),
   which does a kick_all_cpus_sync()
 * bpf_int_jit_compile() calls flush_icache_range().
 * Kprobes calls aarch64_insn_patch_text(), which does its work in
   stop_machine().
 * static keys and ftrace both patch between nops and branches to
   existing kernel code (not generated code).

The affected sequence is the interaction between ftrace and modules.
The module PLT is cleaned using __flush_icache_range() as the trampoline
shouldn't be executable until we update the branch to it.

Drop the double-underscore so that this path runs kick_all_cpus_sync()
too.
Signed-off-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NWill Deacon <will@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>