* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Oprofile: Fix computation of number of counters.
  [MIPS] Alchemy: fix IRQ bases
  [MIPS] Alchemy: replace ffs() with __ffs()
  [MIPS] BCM1480: Fix interrupt routing, take 2.

Make the Kconfig.instrumentation file a bit easier on the eyes, and use
the new ARCH_SUPPORTS_OPROFILE for x86[-64].
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The cleanup 09cadedb broke the oprofile
configuration for MIPS by allowing oprofile support to be built for
kernel models where oprofile doesn't have a chance in hell to work.

Just a dependecy list on a number of architectures is - surprise - broken
and should as per past discussions probably in most considered to be
broken in most cases.  So I introduce a dependency for the oprofile
configuration on ARCH_SUPPORTS_OPROFILE.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

VSMP kernels will split the available performance counters between the two
processors / cores.  But don't do this when we're not on a VSMP system ...
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Do what the commits commits f3e8d1da and
9d360ab4 failed to achieve -- actually
convert the Alchemy code to irq_cpu.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fix havoc wrought by commit 56f621c7 --
au_ffs() and ffs() are equivalent, that patch should have just replaced one
with another.  Now replace ffs() with __ffs() which returns an unbiased bit
number.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  futex: correctly return -EFAULT not -EINVAL
  lockdep: in_range() fix
  lockdep: fix debug_show_all_locks()
  sched: style cleanups
  futex: fix for futex_wait signal stack corruption

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
  VM/Security: add security hook to do_brk
  Security: round mmap hint address above mmap_min_addr
  security: protect from stack expantion into low vm addresses
  Security: allow capable check to permit mmap or low vm space
  SELinux: detect dead booleans
  SELinux: do not clear f_op when removing entries

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  [LRO]: fix lro_gen_skb() alignment
  [TCP]: NAGLE_PUSH seems to be a wrong way around
  [TCP]: Move prior_in_flight collect to more robust place
  [TCP] FRTO: Use of existing funcs make code more obvious & robust
  [IRDA]: Move ircomm_tty_line_info() under #ifdef CONFIG_PROC_FS
  [ROSE]: Trivial compilation CONFIG_INET=n case
  [IPVS]: Fix sched registration race when checking for name collision.
  [IPVS]: Don't leak sysctl tables if the scheduler registration fails.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Update defconfig.
  [SPARC]: Add missing of_node_put
  [SPARC64]: check for possible NULL pointer dereference
  [SPARC]: Add missing "space"
  [SPARC64]: Add missing "space"
  [SPARC64]: Add missing pci_dev_put
  [SYSCTL_CHECK]: Fix typo in KERN_SPARC_SCONS_PWROFF entry string.
  [SPARC64]: Missing mdesc_release() in ldc_init().

endianness annotations in networking code had been in place for quite a
while; in particular, sin_port and s_addr are annotated as big-endian.

Code in ocfs2 had __force casts added apparently to shut the sparse
warnings up; of course, these days they only serve to *produce* warnings
for no reason whatsoever...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

BFS_FILEBLOCKS() expects struct bfs_inode * (on-disk data, with little-
endian fields), not struct bfs_inode_info * (in-core stuff, with host-
endian ones).

It's a macro and fields with the right names are present in
bfs_inode_info, so it compiles, but on big-endian host it gives bogus
results.

Introduced in commit f433dc56 ("Fixes to
the BFS filesystem driver").
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that X86_32 is provided on Kconfig level for uml-i386, there's no
need to play with it explicitly on Makefile level anymore.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

access_flags_to_mode() gets on-the-wire data (little-endian) and treats
it as host-endian.

Introduced in commit e01b6400 ("[CIFS]
enable get mode from ACL when cifsacl mount option specified")
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Given a specifically crafted binary do_brk() can be used to get low pages
available in userspace virtual memory and can thus be used to circumvent
the mmap_min_addr low memory protection.  Add security checks in do_brk().
Signed-off-by: NEric Paris <eparis@redhat.com>
Acked-by: NAlan Cox <alan@redhat.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I can't pass memory allocated by kmalloc() to ksize() if it is allocated by
SLUB allocator and size is larger than (I guess) PAGE_SIZE / 2.

The error of ksize() seems to be that it does not check if the allocation
was made by SLUB or the page allocator.
Reviewed-by: NPekka Enberg <penberg@cs.helsinki.fi>
Tested-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Christoph Lameter <clameter@sgi.com>, Matt Mackall <mpm@selenic.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Creating PDEs with refcount 0 and "deleted" flag has problems (see below).
Switch to usual scheme:
* PDE is created with refcount 1
* every de_get does +1
* every de_put() and remove_proc_entry() do -1
* once refcount reaches 0, PDE is freed.

This elegantly fixes at least two following races (both observed) without
introducing new locks, without abusing old locks, without spreading
lock_kernel():

1) PDE leak

remove_proc_entry			de_put
-----------------			------
			[refcnt = 1]
if (atomic_read(&de->count) == 0)
					if (atomic_dec_and_test(&de->count))
						if (de->deleted)
							/* also not taken! */
							free_proc_entry(de);
else
	de->deleted = 1;
		[refcount=0, deleted=1]

2) use after free

remove_proc_entry			de_put
-----------------			------
			[refcnt = 1]

					if (atomic_dec_and_test(&de->count))
if (atomic_read(&de->count) == 0)
	free_proc_entry(de);
						/* boom! */
						if (de->deleted)
							free_proc_entry(de);

BUG: unable to handle kernel paging request at virtual address 6b6b6b6b
printing eip: c10acdda *pdpt = 00000000338f8001 *pde = 0000000000000000
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: af_packet ipv6 cpufreq_ondemand loop serio_raw psmouse k8temp hwmon sr_mod cdrom
Pid: 23161, comm: cat Not tainted (2.6.24-rc2-8c086340 #4)
EIP: 0060:[<c10acdda>] EFLAGS: 00210097 CPU: 1
EIP is at strnlen+0x6/0x18
EAX: 6b6b6b6b EBX: 6b6b6b6b ECX: 6b6b6b6b EDX: fffffffe
ESI: c128fa3b EDI: f380bf34 EBP: ffffffff ESP: f380be44
 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process cat (pid: 23161, ti=f380b000 task=f38f2570 task.ti=f380b000)
Stack: c10ac4f0 00000278 c12ce000 f43cd2a8 00000163 00000000 7da86067 00000400
       c128fa20 00896b18 f38325a8 c128fe20 ffffffff 00000000 c11f291e 00000400
       f75be300 c128fa20 f769c9a0 c10ac779 f380bf34 f7bfee70 c1018e6b f380bf34
Call Trace:
 [<c10ac4f0>] vsnprintf+0x2ad/0x49b
 [<c10ac779>] vscnprintf+0x14/0x1f
 [<c1018e6b>] vprintk+0xc5/0x2f9
 [<c10379f1>] handle_fasteoi_irq+0x0/0xab
 [<c1004f44>] do_IRQ+0x9f/0xb7
 [<c117db3b>] preempt_schedule_irq+0x3f/0x5b
 [<c100264e>] need_resched+0x1f/0x21
 [<c10190ba>] printk+0x1b/0x1f
 [<c107c8ad>] de_put+0x3d/0x50
 [<c107c8f8>] proc_delete_inode+0x38/0x41
 [<c107c8c0>] proc_delete_inode+0x0/0x41
 [<c1066298>] generic_delete_inode+0x5e/0xc6
 [<c1065aa9>] iput+0x60/0x62
 [<c1063c8e>] d_kill+0x2d/0x46
 [<c1063fa9>] dput+0xdc/0xe4
 [<c10571a1>] __fput+0xb0/0xcd
 [<c1054e49>] filp_close+0x48/0x4f
 [<c1055ee9>] sys_close+0x67/0xa5
 [<c10026b6>] sysenter_past_esp+0x5f/0x85
=======================
Code: c9 74 0c f2 ae 74 05 bf 01 00 00 00 4f 89 fa 5f 89 d0 c3 85 c9 57 89 c7 89 d0 74 05 f2 ae 75 01 4f 89 f8 5f c3 89 c1 89 c8 eb 06 <80> 38 00 74 07 40 4a 83 fa ff 75 f4 29 c8 c3 90 90 90 57 83 c9
EIP: [<c10acdda>] strnlen+0x6/0x18 SS:ESP 0068:f380be44

Also, remove broken usage of ->deleted from reiserfs: if sget() succeeds,
module is already pinned and remove_proc_entry() can't happen => nobody
can mark PDE deleted.

Dummy proc root in netns code is not marked with refcount 1. AFAICS, we
never get it, it's just for proper /proc/net removal. I double checked
CLONE_NETNS continues to work.

Patch survives many hours of modprobe/rmmod/cat loops without new bugs
which can be attributed to refcounting.
Signed-off-by: NAlexey Dobriyan <adobriyan@sw.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Before we start committing a transaction, we call
__journal_clean_checkpoint_list() to cleanup transaction's written-back
buffers.

If this call happens to remove all of them (and there were already some
buffers), __journal_remove_checkpoint() will decide to free the transaction
because it isn't (yet) a committing transaction and soon we fail some
assertion - the transaction really isn't ready to be freed :).

We change the check in __journal_remove_checkpoint() to free only a
transaction in T_FINISHED state.  The locking there is subtle though (as
everywhere in JBD ;().  We use j_list_lock to protect the check and a
subsequent call to __journal_drop_transaction() and do the same in the end
of journal_commit_transaction() which is the only place where a transaction
can get to T_FINISHED state.

Probably I'm too paranoid here and such locking is not really necessary -
checkpoint lists are processed only from log_do_checkpoint() where a
transaction must be already committed to be processed or from
__journal_clean_checkpoint_list() where kjournald itself calls it and thus
transaction cannot change state either.  Better be safe if something
changes in future...
Signed-off-by: NJan Kara <jack@suse.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Writing to XIP files at a non-page-aligned offset results in data corruption
because the writes were always sent to the start of the page.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The AMD CS5535/CS5536 GPIO has two alternate output modes: AUX-1 and AUX-2.
When either AUX is enabled, the cs5535_gpio driver cannot control the
output.

Some BIOS code for the Geode processor enables AUX-1 for GPIO-1, which
configures it as the PC BEEP output.

This patch will disable AUX-1 and AUX-2 when the user enables output.
Signed-of-by: NBen Gardner <gardner.ben@gmail.com>
Cc: Richard Knutsson <ricknu-0@student.ltu.se>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

register_sysctl_table() can return NULL sometimes, e.g.  when kmalloc()
returns NULL or when sysctl check fails.

I've also noticed, that many (most?) code in the kernel doesn't check for
the return value from register_sysctl_table() and later simply calls the
unregister_sysctl_table() with potentially NULL argument.

This is unlikely on a common kernel configuration, but in case we're
dealing with modules and/or fault-injection support, there's a slight
possibility of an OOPS.

Changing all the users to check for return code from the registering does
not look like a good solution - there are too many code doing this and
failure in sysctl tables registration is not a good reason to abort module
loading (in most of the cases).

So I think, that we can just have this check in unregister_sysctl_table
just to avoid accidental OOPS-es (actually, the unregister_sysctl_table()
did exactly this, before the start_unregistering() appeared).
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

 - reconfigure SPI baud from speed_hz of each spi transfer
 - according to spi_transfer.bits_per_word to reprogram register and setup
   correct SPI operation handlers
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time

 - move this static things to the blackfin board file
 - add pin_req array to struct bfin5xx_spi_master
 - tested on BF537/BF548 with SPI flash
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Set correct baud for spi mmc and enable SPI only after DMA is started.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move cs_chg_udelay handling (specific to this driver) to cs_deactive(), fixing
a bug when some SPI LCD driver needs delay after cs_deactive.

Fix bug reported by Cameron Barfield <cbarfield@cyberdata.net>
https://blackfin.uclinux.org/gf/project/uclinux-dist/forum/?action=ForumBrowse&forum_id=39&_forum_action=ForumMessageBrowse&thread_id=23630&feedback=Message%20replied.

Cc: Cameron Barfield <cbarfield@cyberdata.net>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix bug in u16_cs_chg_reader to read data_len-2 bytes data firstly, then read
out the last 2 bytes data
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move global SPI regs_base and dma_ch to struct driver_data.  Test on BF54x SPI
Flash with 2 spi_master devices enabled.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move spin/waits to more correct locations in bfin SPI driver.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix SPI driver to work with SPI flash ST M25P16 on bf548

Currently the SPI driver enables the SPI controller and sets the SPI baud
register for each SPI transfer.  But they should never be changed within a SPI
message session, in which several SPI transfers are pumped.

This patch moves SPI setting to the begining of a message session, and
never disables SPI controller until an error occurs.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move pin muxing to setup and cleanup methods.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use portmux mechanism to support SPI busses 1 and 2, instead of just the
original bus 0.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update spi driver to support multi-ports by using platform resources; tested
on STAMP537+SPI_MMC, other boards need more testing.  Plus other minor
updates.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Prevent people from setting bits in ctl_reg that the SPI framework already
handles, hopefully we can one day drop ctl_reg completely
Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Respect per-transfer cs_change field (protocol tweaking support) by
adding and using cs_active/cs_deactive functions.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cleanup and error handling

 - add error handling in SPI bus driver with selecting clients
 - use proper defines to access Blackfin MMRs
 - remove useless SSYNCs
 - cleaner use of portmux calls
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use new Blackfin portmux interface, add error handling.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>