Bump i40e to 1.2.10 and i40evf to 1.2.4

Change-ID: I48aa64df05fcc8356e7026f3a9e69ecf78d0c785
Signed-off-by: NSravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In case of MFP mode the driver was returning incorrect number of TCs
for partitions that are not enabled for iSCSI. Though the driver does
not configure these TCs in the Tx scheduler for the NIC partitions;
it does use this map to setup the queue mappings.

This patch fixes this and keeps all the NIC partitions to the default
PF TC i.e. TC0.

Change-ID: Iede214c907e7bac1356e999049b9f642759512b3
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allow DCBNL operations in MFP mode to allow query of port DCB settings
via all the PFs and register iSCSI APP on iSCSI enabled PF.

Change-ID: I34cc39b4665d0a631847d4079350d3814f02381e
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add an extra check to make sure that the indirection table pointer is
valid before dereferencing it.

Change-ID: I698adbf3daff03081d01f489dc95a9f1ad8b12f1
Reported-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With changes to default number of queue pairs that the interface comes up with
from 1 per online CPU to 1 per lan_msix, we need to make sure we recalculate
rss_size. We will now recalculate rss_size based on number of queues enabled in
the VSI.

Without this fix if the max_lan_msix < num_online_cpu we will be coming up
with fewer queues but will be populating rss_size based on num_online_cpus.
This will result in packets getting silently dropped because RSS LUT has queues
that are not enabled.

Change-ID: Ifac8796ce1be1758bb0c34f38dbf4a3a76621e76
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since all VSIs don't have the same RSS table size,
have one for each VSI instead of having a single define
for RSS table size

Change-ID: Ic2c7c66e4a389d4b6c8841a707510a9735041f02
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were missing a few packet types for VXLAN offload. This patch fixes
that.

Change-ID: I4b23aa0b08e40ed49d0df6c49a5ed9f2009b44ce
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes an issue where the driver is not flushing out the
DCBNL app table for applications that are not present in the local
DCBX application configuration TLVs.

Change-ID: I1f1ee04c81c145071b2ab15657546eb10b81fadb
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For FW < 4.33 DCB should be disabled.
Also Autoneg workaround to avoid Rx stall is still needed for FW < 4.33.

Change-ID: Iff36ad86be2f597e7701096014d6d094332a9a21
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When running in a single TC mode the HW can be configured to enable more
than max RSS qps for the Main VSI. This  patch makes it possible to
enable as many as num_online_cpus().

ethtool -L can still be used to reconfigure number of qps
to a smaller value.

Change-ID: I3e2df085276982603d86dfd79477c0ada8d30b8f
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we now have functionality to enable and disable PF loopback at
runtime, don't try to do it automatically. Removing this call also gets
rid of a bogus error message when removing the PF module with VFs
enabled.

Change-ID: Ic38652d8a3b9498d96113bfaa5ea7bad050862e9
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds default case to handle unmatched switch calls.

Change-ID: Icd203570a1dc5322c1038f68b98a83195e8ad28c
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Include the FW build number in the formatted FW version string.  In order
to fit within ethtool's 32 character limit, the etrack's unused high order
bits are trimmed as is the leading 0 for the NVM version.  This leaves
us with 2 character left for if/when the etrack id goes to 5 hex chars
and the NVM major number goes to 2 chars.

Change-ID: Icb004c4b9b14a2f54dd200b467fcc1d7b9297308
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If DCB is not enabled priority tagging is not needed
so skip over that section.

Change-ID: Ia3f3fa07945b421259a9ca38329d6d1cbd6c6bcc
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a few silly typos in the code and checkpatch warnings in support of
general code cleanliness.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The introduction of ndo_features_check allows drivers to report their
offload capabilities per-skb. Implement this in fm10k to take advantage
of this new functionality.
Reported-by: NJoe Stringer <joestringer@nicira.com>
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The FM10000 host interface can only support up to 184 bytes when
performing tunnel offloads. Because of this, a check was added to
prevent the driver from attempting to feed a header to the hardware too
big for it to parse. Make this check a little more robust by calculating
the inner L4 header length based on whether it is TCP or UDP.

Cc: Joe Stringer <joestringer@nicira.com>
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e to 1.2.9 and i40evf 1.2.3

Also update the copyright year.

Change-ID: I345d777e94abd0acffe6a28793f675d251a86299
Signed-off-by: NSravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds the netdev name to the VF misc vector name.  Without
this patch, all the interrupts show the same info, so it difficult to
distinguish them.

Change-ID: I247828697e1373ecfb5f8dc1bc9618e98a7f4942
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allow an application to query the i40e driver's private flags to get the
status of NPAR enablement.  This will be used by applications to determine
if there are NPAR specific features available.

Change-ID: Ia6d9477a48f9c4cb41ca022bd433f77da3f2146c
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Set FLAG_RD for send_driver_version AQ command.

Change-ID: I8253051eff85a1d4b5a4e12ce0395b65ceb91e62
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the RX routine in use to the features log message.

Change-ID: Ifbbf28fb7f42b9a3d2828586488e9e6331107dd5
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Setup FCoE netdev device type as "fcoe", so that it shows up in
sysfs as FCoE device.

Change-ID: Ie13a1a332dba4d5802586926104ee01ef20da44f
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

BUF flag must be set for indirect AQ command.

Change-ID: I6819718a47baf69d1a91ebaed89f735ed6e86025
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for bridge offload ndo_ops getlink and setlink to
enable bridge hardware mode as per the mode set via IFLA_BRIDGE_MODE.
The support is only enabled in case of a PF VSI and not available for
any other VSI type.

By default the i40e driver inserts a bridge as part of the bring-up
when a FDIR type VSI and/or a FCoE VSI is created. This bridge is
created in VEB mode by default i.e. after creating the bridge using
"Add VEB" AQ command the loopback for the PF's default VSI is enabled.

The patch adds capability where all the VSIs created as downlink to
the bridge inherits the loopback property and enables loopback only
if the uplink bridge is operating in VEB mode.
Hence, there is no need to explicitly enable loopback as part of
allocating resources for SR-IOV VFs and call to do that has been
removed.

In case a user-request is made either via "bridge" utility or using
the bridge netlink interface that requires to change the hardware
bridge mode then that would require a PF reset and rebuild of the
switch hierarchy.

Also update the copyright year.

Change-ID: I4d78fc1c83158efda29ba7be92239b74f75d6d25
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add configfs controls to get, set and commit NPAR BW configurations.

We export three controls:
	min_bw - Can take a value from 0 to 100 inclusive
	max_bw - Can take a value from 1 to 100 inclusive
	commit - A write-only control that accepts only a value of 1 and will
		cause the BW settings to be permanently committed to NVM so
		that they are persistent across power cycles and system
		resets

The BW values are relative and are expressed as percentages.  For more
information on the interpretation of the BW settings see the Dell
specifications for NPAR.

Also update the copyright year.

Change-ID: Id7496ca65630b5037e32ba6a5a748fbc1632881b
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-By: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We need to be able to get, set and commit permanently the NPAR
partition BW configuration through configfs.  These are necessary
precursor functions for that feature.

Also update the copyright year.

Change-ID: I9d5ca160a9288145f1dd2042994028679fff55f3
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When an IOMMU is in use, the packet split receive path shows a distinct
advantage over the single-buffer path because it minimizes DMA mapping
and unmapping. However, this is not an advantage for systems with no
IOMMU. At init time, check to see if an IOMMU is enabled and enable
packet split receives.

Change-ID: I4f70d2e9c31bbea3dc8fd0c5734959a6e6602210
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Copy setting from ethtool to the HW specific struct to actually
enable prints.  Change print from i40e to i40evf to differentiate
drivers in bare metal scenarios.

Also update the copyright year.

Change-ID: I06fee26247299a08f2e1c70fc811a9ea0931c4dd
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a struct to the VSI struct to keep track of rxnfc
settings done via ethtool.  Without this patch, the device can only
list the options available, not the current settings and this is not
clear to the user.  Without current settings, the available settings
never changing looks like a bug.

Also update the copyright year.

Change-ID: I087bbfdb33b330496a671630a7586773e3b3e589
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a requested speed variable to the link_status struct to store the
last speeds we requested from the firmware (the speeds the FW will be
advertising with if autoneg is enabled).

Use the advertised speed settings in get_settings in ethtool now that
we have it.  Also set the requested speed settings in set_settings in
ethtool as they are requested and initialize them in probe based on what
the firmware remembers as the last requested speeds.

To accommodate some longer lines in this new code, and improve
readability I have added two functions i40e_get_settings_link_up
and i40e_get_settings_link_down which get_settings now calls first.
It then does all of the settings that happen regardless of link
state. Some PHY types that supported the same settings were also combined.

Also update the copyright year.

Change-ID: Ica0c5ac81b6069ea6a7406fce7482f7816d4455c
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function i40e_debug_aq() prints information helpful in debugging
admin queue commands, but it doesn't do so correctly on big endian machines.
This patch adds the appropriate LExx_TO_CPU wrappers for big endian
architectures.

Also update the copyright year.

Change-ID: I4b2dc229ed5bf6dfe35632a58cddf53c21aff4b0
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Under rare circumstances, after a reset, set_rx_mode might get called
while the watchdog is running, which will cause a deadlock on the
critical section lock. To correct this, add a counter and give up trying
to get the lock after fifty tries. Log a message if this happens but
don't take any other action. Because this happens after a reset, all of
the Rx filters are still in place and the device won't lose
connectivity.

We can also get stuck during shutdown, if the PF has stopped communicating
with us, or if a reset is occurring. If we can't get the lock after a reasonable
amount of time, just error out. Something else bad is happening anyway, so
adding this filter is the least of our concern right now.

Change-ID: I159731e2a82a06b389ee31b34ce336548e05baa0
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A recent change to the shutdown flow messed up the reset flow. Since
i40evf_down now holds the critical section lock, we cannot call it from
the reset handler, which also holds the lock. To do so causes a deadlock
accompanied by wailing and gnashing of teeth. This is easily triggered
by running an ethtool self-test on the PF device.

Instead, we move the relevant portions of i40evf_down into the reset
handler and bend them to our will. Additionally, we can optimize the
reinit path by not deleting the MAC and VLAN filters and then adding
them back again. Instead, we just set the 'add' flag and let the
watchdog resynchronize the filter list with the PF driver. We also
reword a few messages to make them more consistent with the rest of the
driver.

Change-ID: I03dd92ae736f7719fca3564b12a2cf9b98c6cb18
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When closing the interface, disable NAPI polling before any other
activities. This fixes an occasional panic during close caused by the
driver trying to delete and clean rings at the same time.

Change-ID: Ib4d427b13d310258ea85b248d535da70ecf0c1e9
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The netdev op that allows the operator to turn MAC/VLAN spoof checking on
and off did not include the flag for VLAN spoof checking.  This patch
fixes that problem.

Change-ID: Ib4c9e639024a854592d97af22706544881ac3fcb
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e to 1.2.8 and i40evf to 1.2.2

Change-ID: I64f47c3367ea8ff2a53068e895d7a1f60726c871
Signed-off-by: NSravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

An_enable was never used only set so lets remove it. The function
update_link_info only did two things, call get_link_info and set
an_enabled. Therefore we should also remove update_link_info and
change all references to it to get_link_info.

Change-ID: Ie3022680fa7a94bfd495a4f5fc76a73701d85569
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We shouldn't trigger another EMPR when we receive an EMPR event.
This patch handles EMPR event reception with a different state
so that we can do the right thing for NVM.

Change-ID: I9cac70b3658600f016a65beb6fb157e1c1f9adf9
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some registers have been removed so take them out and
stop updating and looking at them.

Change-ID: I33da922c8de993a94dd8b8d8a2ae2146b8ca1a27
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>