Address families of source and destination addresses must match, and
changelink operations can't change the address family.

In addition, always use the VXLAN_F_IPV6 to check if a VXLAN device uses
IPv4 or IPv6.
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no good reason to keep the flags twice in vxlan_dev and
vxlan_config.
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vxlan_dev_configure function was mixing validation and application of
the vxlan configuration; this could easily lead to bugs with the changelink
operation, as it was hard to see if the function wcould return an error
after parts of the configuration had already been applied.

This commit splits validation and application out of vxlan_dev_configure as
separate functions to make it clearer where error returns are allowed and
where the vxlan_dev or net_device may be configured. Log messages in these
functions are removed, as it is generally unexpected to find error output
for netlink requests in the kernel log. Userspace should be able to handle
errors based on the error codes returned via netlink just fine.

In addition, some validation and initialization is moved to vxlan_validate
and vxlan_setup respectively to improve grouping of similar settings.

Finally, this also fixes two actual bugs:

* if set, conf->mtu would overwrite dev->mtu in each changelink operation,
  reverting other changes of dev->mtu
* the "if (!conf->dst_port)" branch would never be run, as conf->dst_port
  was set in vxlan_setup before. This caused VXLAN-GPE to use the same
  default port as other VXLAN sockets instead of the intended IANA-assigned
  4790.
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

yuan linyu says:

====================
net: more skb_put_[data:zero] related work

yuan linyu (3):
  net: introduce __skb_put_[zero, data, u8]
  net: replace more place to skb_put_[data:zero]
  net: manual clean code which call skb_put_[data:zero]
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: Nyuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

spatch file,
@@
expression skb, len, data;
type t;
@@
-memcpy((t *)skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);

@@
identifier p;
expression skb, len, data;
type t;
@@
-p = (t *)memset(skb_put(skb, len), data, len);
+p = skb_put_zero(skb, len);

@@
expression skb, len, data;
type t;
@@
-memcpy((t *)__skb_put(skb, len), data, len);
+__skb_put_data(skb, data, len);

@@
identifier p;
expression skb, len, data;
type t;
@@
-p = (t *)memset(__skb_put(skb, len), data, len);
+p = __skb_put_zero(skb, len);
Signed-off-by: Nyuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

follow Johannes Berg, semantic patch file as below,
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = __skb_put(skb, len);
+p = __skb_put_zero(skb, len);
|
-p = (t)__skb_put(skb, len);
+p = __skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)

@@
identifier p;
expression len;
expression skb;
type t;
@@
(
-t p = __skb_put(skb, len);
+t p = __skb_put_zero(skb, len);
)
... when != p
(
-memset(p, 0, len);
)

@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = __skb_put(skb, sizeof(t));
+p = __skb_put_zero(skb, sizeof(t));
|
-p = (t *)__skb_put(skb, sizeof(t));
+p = __skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)

@@
expression skb, len;
@@
-memset(__skb_put(skb, len), 0, len);
+__skb_put_zero(skb, len);

@@
expression skb, len, data;
@@
-memcpy(__skb_put(skb, len), data, len);
+__skb_put_data(skb, data, len);

@@
expression SKB, C, S;
typedef u8;
identifier fn = {__skb_put};
fresh identifier fn2 = fn ## "_u8";
@@
- *(u8 *)fn(SKB, S) = C;
+ fn2(SKB, C);
Signed-off-by: Nyuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kill the remaining shift macro in favor of calculating at compile time
its value from the more descriptive mask, which gives us a better
representation of the register layout.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: Global 2 cosmetics

Similarly to what has been done for the Port and Global 1 registers,
this patch series prefixes and documents the macros of Global 2.

It brings no functional changes except for 1/10 which fixes the IRL init
for 88E6390 family.

Changes in v2: make *_g2_irl_init_all static inline without
NET_DSA_MV88E6XXX_GLOBAL2 and compile test with and without the symbol.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the remaining Global 2 registers macros.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell 88E6352 family has a Global 2 register dedicated to the
watchdog setup. But the 88E6390 turned it into an indirect table.

Prefix and document that.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the Global 2 Switch MAC registers macros.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the Global 2 EEPROM registers macros.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the Global 2 Cross-chip Port VLAN registers macros.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the Global 2 MGMT registers macros.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the Global 2 Device Mapping macros.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefix and document the Global 2 Trunk registers macros. At the same
time, fix the hask -> hash typo and use the mv88e6xxx_port_mask helper.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marvell chips with an SMI PHY access in Global 2 registers handle both
Clause 22 and Clause 45 of IEEE 802.3.

The 88E6390 family has addition bits to target the internal or external
PHYs connected to the device, and a Setup function in addition to the
default (register) Access function.

Prefix the SMI PHY Command and Data registers macros, implement clear
helpers for Clause 22 and 44 Access functions, rename variable to match
the SMI and switch vocabulary (device and register addresses for Clause
22 and port and device class for Clause 45.)

Finally do not use complex macros but simple 16-bit mask to document the
registers organization.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some Marvell chips have an Ingress Rate Limit unit. But the command
values slightly differs between models: 88E6352 use 3-bit for operations
while 88E6390 use different 2-bit operations.

This commit kills the IRL flags in favor of a new operation implementing
the "Init all resources to the initial state" operation.

This fixes the operation of 88E6390 family where 0x1000 means Read the
selected resource 0, register 0 on port 16, instead of init all.

A mv88e6xxx_irl_setup helper is added to wrap the operation call.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Icenowy Zheng says:

====================
net-next: stmmac: dwmac-sun8i: add support for V3s

Allwinner V3s features an EMAC like the on in H3, but without external MII
interfaces, so being not able really to use RMII/RGMII.

And it has a different default value of syscon (0x38000 instead of 0x58000
on H3), which shows a problem that the EMAC clock freq should be 24MHz.
(Both H3 and V3s SoCs doesn't have extra xtal input for EPHY, and the
main xtal is 24MHz. The default value of H3 is set to 24MHz, but the V3s
default value is set to 25MHz).

First two patches are device tree binding patches, the third forces
the frequency to 24MHz and the fourth really add the V3s support.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allwinner V3s SoC has an Ethernet MAC and an internal PHY like the ones
in H3 SoC, however the MAC has no external *MII interfaces available at
GPIOs, thus only MII connection to internal PHY is supported.

Add this variant of EMAC to dwmac-sun8i driver.

The default value of the syscon EMAC-related register seems to have
changed from H3, but it seems to be a harmless change.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EPHY control part of the EMAC syscon register has a bit called
CLK_SEL. On the datasheet it says that if it's 0 the EPHY clock is 25MHz
and if it's 1 the clock is 24MHz.

However, according to the datasheets, no Allwinner SoC with EPHY has any
extra xtal input pins for the EPHY, and the system xtal is 24MHz.

That means the EPHY is not possible to get a 25MHz xtal input, and thus
the frequency can only be 24MHz.

It doesn't matter on H3 as the default value of H3 is 24MHz, however on
V3s the default value is wrongly set to 25MHz, which prevented the EPHY
from working properly.

Force the EPHY clock frequency to 24MHz.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allwinner V3s SoC has a syscon like the one in H3.

Add its compatible string.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allwinner V3s SoC has a Ethernet MAC like the one in Allwinner H3, but
have no external MII capability. That means that it can only use the
EPHY and cannot do Gbps transmission.

Add binding for it.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lucas Bates says:

====================
net: Introduction of the tc tests

Apologies for sending this as one big patch. I've been sitting on this a little
too long, but it's ready and I wanted to get it out.

There are a limited number of tests to start - I plan to add more on a regular
basis.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the beginnings of a testsuite for tc functionality in the kernel.
These are a series of unit tests that use the tc executable and verify
the success of those commands by checking both the exit codes and the
output from tc's 'show' operation.

To run the tests:
  # cd tools/testing/selftests/tc-testing
  # sudo ./tdc.py

You can specify the tc executable to use with the -p argument on the command
line or editing the 'TC' variable in tdc_config.py. Refer to the README for
full details on how to run.

The initial complement of test cases are limited mostly to tc actions. Test
cases are most welcome; see the creating-testcases subdirectory for help
in creating them.
Signed-off-by: NLucas Bates <lucasb@mojatatu.com>
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed*: RDMA and infrastructure for iWARP

This series focuses on RDMA in general with emphasis on required changes
toward adding iWARP support. The vast majority of the changes introduced
are in qed/qede, with a couple of small changes to qedr
[mentioned below].

The infrastructure changes:
 - Patch #1 adds the ability to pass PBL memory externally for a newly
created chain.
 - Patches #4, #5 rename qede_roce.[ch] into qede_rdma.[ch] + change
prefixes from _roce_ to _rdma_, as the API between qede and qedr is
agnostic to the variant of the RDMA protocol used. These patches also
touch qedr [basically to align it with the renaming, nothing more].
 - Patch #7 replaces the current SPQ async mechanism into serving
registered callbacks [before adding iWARP which would add another client
in need of this sort of functionallity].

The non-infrastrucutre changes:
 - Patches #2, #3 contain DCB-related changes to better align RDMA with
configured DCB.
 - Patch #6 contains a minor [mostly theoretical fix] to release flow.

Changes from previous versions
------------------------------
 - V4: This is actually a repost of V3 due to some confusion regarding
   the sent cover-letter
 - V3: Add commit log message in #4 indicating change in header inclusion
 - V2: Add several inclusion into qede_rdma.h to have proper declarations
   of all variable types used in it
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Whenever firmware indicates that there's an async indication it needs
to handle, there's a switch-case where the right functionality is called
based on function's personality and information.

Before iWARP is added [as yet another client], switch over the SPQ into
a callback-registered mechanism, allowing registration of the relevant
event-processing logic based on the function's personality. This allows
us to tidy the code by removing protocol-specifics from a common file.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver needs to wait for all resources to return from FW before it can send
the FUNC_CLOSE ramrod.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the functions common to both iWARP and RoCE to have a prefix of
_rdma_ instead of _roce_.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Once we have iWARP support, the qede portion of the qedr<->qede would
serve all the RDMA protocols - so rename the file to be appropriate
to its function.

While we're at it, we're also moving a couple of inclusions to it into
.h files and adding includes to make sure it contains all type
definitions it requires.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If DCBx update occurs while QPs are open, stop sending edpms until all
QPs are closed.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configure device according to DCBx results so that EDPMs
made by RoCE would honor flow-control.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

iWARP would require the chains to allocate/free their PBL memory
independently, so add the infrastructure to provide it externally.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace first padding in the tcp_md5sig structure with a new flag field
and address prefix length so it can be specified when configuring a new
key for TCP MD5 signature. The tcpm_flags field will only be used if the
socket option is TCP_MD5SIG_EXT to avoid breaking existing programs, and
tcpm_prefixlen only when the TCP_MD5SIG_FLAG_PREFIX flag is set.
Signed-off-by: NBob Gilligan <gilligan@arista.com>
Signed-off-by: NEric Mowat <mowat@arista.com>
Signed-off-by: NIvan Delalande <colona@arista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows the keys used for TCP MD5 signature to be used for whole
range of addresses, specified with a prefix length, instead of only one
address as it currently is.
Signed-off-by: NBob Gilligan <gilligan@arista.com>
Signed-off-by: NEric Mowat <mowat@arista.com>
Signed-off-by: NIvan Delalande <colona@arista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During the module initialisation there is a possible race
(basically race between uld and lld) where neither the uld
nor lld notifies the uP about where to route the ctrl queue
completions. LLD skips notifying uP as the rdma queues were
not created by then (will leave it to ULD to notify the uP).
As the ULD comes up, it also skips notifying the uP as the
flag FULL_INIT_DONE is not set yet (ULD assumes that the
interface is not up yet).

Consequently, this race between uld and lld leaves uP
unnotified about where to send the ctrl queue completions
to, leading to iwarp RI_RES WR failure.

Here is the race:

CPU 0                                   CPU1

- allocates nic rx queus
- t4_sge_alloc_ctrl_txq()
(if rdma rsp queues exists,
tell uP to route ctrl queue
compl to rdma rspq)
                                - acquires the mutex_lock
                                - allocates rdma response queues
                                - if FULL_INIT_DONE set,
                                  tell uP to route ctrl queue compl
                                  to rdma rspq
                                - relinquishes mutex_lock
- acquires the mutex_lock
- enable_rx()
- set FULL_INIT_DONE
- relinquishes mutex_lock

This patch fixes the above issue.

Fixes: e7519f99('cxgb4: avoid enabling napi twice to the same queue')
Signed-off-by: NRaju Rangoju <rajur@chelsio.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
CC: Stable <stable@vger.kernel.org> # 4.9+
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 0x6082, 0x6083 and 0x6084 T6 device id's
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add general use per-vNIC mailbox area and use it for VLAN filtering
support.  Initially proto is hardcoded to 802.1q.
Signed-off-by: NPablo Cascón <pablo.cascon@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid NULL dereference in setup_sge_queues() when the adapter is
in non offload mode.

Fixes: 0fbc81b3 ('chcr/cxgb4i/cxgbit/RDMA/cxgb4: Allocate resources dynamically for all cxgb4 ULD's')
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>