Convert all USB gadget sysfs attributes to use the _RO or _RW variants,
to make them easier to audit and ensure that the permissions are
correct.

Note, two are left using the DEVICE_ATTR() macro, as there is no
DEVICE_ATTR_WO() in Linus's tree, that will happen after 3.12-rc1 is
out, a follow-on patch will be sent then.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

--
 drivers/usb/gadget/composite.c      |    8 +++-----
 drivers/usb/gadget/dummy_hcd.c      |    8 ++++----
 drivers/usb/gadget/f_mass_storage.c |   14 ++++++--------
 drivers/usb/gadget/net2272.c        |    4 ++--
 drivers/usb/gadget/net2280.c        |   18 +++++++++---------
 drivers/usb/gadget/storage_common.c |   25 ++++++++++++-------------
 drivers/usb/gadget/udc-core.c       |   14 +++++++-------
 7 files changed, 43 insertions(+), 48 deletions(-)

Clean up the DEVICE_ATTR usage in the USB serial drivers, making them
more obvious as to the permissions that the sysfs files should be.

Note: ftdi_sio.c still has a DEVICE_ATTR() used, that will have to wait
until after 3.12-rc1 comes out when DEVICE_ATTR_WO() shows up in Linus's
tree.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In auditing the usbtmc sysfs files, a bunch of them were being created
as "read only", yet they have logic to handle writing to.  So fix them
up by setting the permissions properly.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of having to audit all sysfs attributes, to ensure we get them
right, use the default macros the driver core provides us (read-only,
read-write) to make the code simpler, and to prevent any mistakes from
ever happening.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use DRIVER_ATTR_RW() to make it easier to audit sysfs file permissions.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

After successful initialization hub->descriptor->bNbrPorts and
hub->hdev->maxchild are equal, but using hub->hdev->maxchild is
preferred because that value is explicitly used for initialization
of hub->ports[].
Signed-off-by: NKrzysztof Mazur <krzysiek@podlesie.net>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Ignoring usb_hub_create_port_device() errors cause later NULL pointer
deference when uninitialized hub->ports[i] entries are dereferenced
after port memory allocation error.
Signed-off-by: NKrzysztof Mazur <krzysiek@podlesie.net>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the hub_configure() fails after setting the hdev->maxchild
the hub->ports might be NULL or point to uninitialized kzallocated
memory causing NULL pointer dereference in hub_quiesce() during cleanup.

Now after such error the hdev->maxchild is set to 0 to avoid cleanup
of uninitialized ports.
Signed-off-by: NKrzysztof Mazur <krzysiek@podlesie.net>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 7e8d5cd9 ("USB: Add EHCI support for MX27 and MX31 based
boards") introduced code that could potentially lead to a NULL pointer
dereference on driver removal.

Fix this by checking for the value of pdata before dereferencing it.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org> # 2.6.33+
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These local symbols are used only in this file.
Fix the following sparse warnings:

drivers/uwb/drp-ie.c:30:5: warning: symbol 'uwb_rsv_reason_code' was not declared. Should it be static?
drivers/uwb/drp-ie.c:58:5: warning: symbol 'uwb_rsv_companion_reason_code' was not declared. Should it be static?
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix endianess bugs in parallel-port code which caused corrupt
control-requests to be issued on big-endian machines.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The write_parport_reg_nonblock() function shouldn't sleep because it's
called with spinlocks held.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Acked-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The documentation for the USB gadget fs is actually in
Documentation/usb/gadget_configfs.txt.
Signed-off-by: NPhilippe De Swert <philippe.deswert@jollamobile.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

usb-serial-simple uses an unknown stringify macro that make
all drivers being named "stringify(vendor)".

This can be a problem when two drivers have the same (wrong) name:

    kernel: usbcore: registered new interface driver usb_serial_simple
    kernel: usbserial: USB Serial support registered for stringify(vendor)
    kernel Error: Driver 'stringify(vendor)' is already registered, aborting...
    kernel: usbserial: problem -16 when registering driver stringify(vendor)
    kernel: usbserial: USB Serial deregistering driver stringify(vendor)
    kernel: usbcore: deregistering interface driver usb_serial_simple

Before the fix:

    $ strings drivers/usb/serial/usb-serial-simple.o
    usb_serial_simple
    stringify(vendor)

After the fix:

    $ strings drivers/usb/serial/usb-serial-simple.o
    usb_serial_simple
    funsoft
    flashloader
    vivopay
    moto_modem
    hp4x
    suunto
    siemens_mpi

This patch makes usb-serial-simple use the correct stringify operator.
Signed-off-by: NYann Droneaud <ydroneaud@opteya.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In wa_seg_init, use usb_init_urb to init the URB object contained in the
transfer segment instead of initializing it manually.  Use kmalloc to
allocate the memory for segment instead of kzalloc and then use memset
to set the non-URB portion of the transfer segment struct to 0 since
that was already done by usb_init_urb.
Signed-off-by: NThomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The check to free the URB was the opposite of the correct case.  This
patch removes the check altogether since the ptr will be NULL if the URB
was not allocated.  Also use usb_free_urb instead of usb_put_urb.
Signed-off-by: NThomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use usb_free_urb instead of kfree in error path and point to the correct
URB.  Also remember to clean up the sg list for the URB if it was allocated.
Signed-off-by: NThomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the HWA encounters a STALL on a control endpoint, it should clear the
RPIPE_STALL feature on the RPIPE before processing the next transfer
request.  Otherwise, all transfer requests on that endpoint after the
first STALL will fail because the RPIPE is still in the halted state.
This also removes the unneccessary call to spin_lock_irqsave for a nested
lock that was present in the first patch.
Signed-off-by: NThomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the previous QUERY_PAGES command version we used one command to get the
required amount of boot, init and post init pages.  The new version uses the
op_mod field to specify whether the query is for the required amount of boot,
init or post init pages. In addition the output field size for the required
amount of pages increased from 16 to 32 bits.

In MANAGE_PAGES command the input_num_entries and output_num_entries fields
sizes changed from 16 to 32 bits and the PAS tables offset changed to 0x10.

In the pages request event the num_pages field also changed to 32 bits.

In the HCA-capabilities-layout the size and location of max_qp_mcg field has
been changed to support 24 bits.

This patch isn't compatible with firmware versions < 5; however, it  turns out that the
first GA firmware we will publish will not support previous versions so this should be OK.
Signed-off-by: NMoshe Lazer <moshel@mellanox.com>
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent fix d9bf5f13 "tun: compare with 0 instead of total_len" is
not totally correct.  Because "len" and "sizeof()" are size_t type, that
means they are never less than zero.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Do not allow interrupt test when adapter is resetting.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Driver was misinterpreting the return status for beacon
  state query leading to incorrect interpretation of beacon
  state and logging an error message for successful status.
  Fixed the driver to properly interpret the return status.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver was issuing set driver version command through all
functions in the adapter. Fix the driver to issue set driver
version once per adapter, through function 0.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d8af4dfd ("net/tg3: Fix kernel crash") introduced a possible
NULL pointer dereference in tg3 driver when !netdev || !netif_running(netdev)
condition is met and netdev is NULL. Then, the jump to the 'done' label
calls dev_close() with a netdevice that is NULL. Therefore, only call
dev_close() when we have a netdevice, but one that is not running.

[ Add the same checks in tg3_io_slot_reset() per Gavin Shan - by Nithin
Nayak Sujir ]
Reported-by: NDave Jones <davej@redhat.com>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Gavin Shan <shangw@linux.vnet.ibm.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The xHCI platform driver calls into usb_add_hcd to register the irq for
its platform device.  It does not want the xHCI generic driver to
register an interrupt for it at all.  The original code did that by
setting the XHCI_BROKEN_MSI quirk, which tells the xHCI driver to not
enable MSI or MSI-X for a PCI host.

Unfortunately, if CONFIG_PCI is enabled, and CONFIG_USB_DW3 is enabled,
the xHCI generic driver will attempt to register a legacy PCI interrupt
for the xHCI platform device in xhci_try_enable_msi().  This will result
in a bogus irq being registered, since the underlying device is a
platform_device, not a pci_device, and thus the pci_device->irq pointer
will be bogus.

Add a new quirk, XHCI_PLAT, so that the xHCI generic driver can
distinguish between a PCI device that can't handle MSI or MSI-X, and a
platform device that should not have its interrupts touched at all.
This quirk may be useful in the future, in case other corner cases like
this arise.

This patch should be backported to kernels as old as 3.9, that
contain the commit 00eed9c8 "USB: xhci:
correctly enable interrupts".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NYu Y Wang <yu.y.wang@intel.com>
Tested-by: NYu Y Wang <yu.y.wang@intel.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org

Userspace can tell the kernel to power off any USB port, including ones
that are visible and connectible to users.  When an attached USB device
goes into suspend, the port will be powered off if the
pm_qos_no_port_poweroff file for its port is set to 0, the device does
not have remote wakeup enabled, and the device is marked as persistent.

If the user disconnects the USB device while the port is powered off,
the current code does not handle that properly.  If you disconnect a
device, and then run `lsusb -v -s` for the device, the device disconnect
does not get handled by the USB core.  The runtime resume of the port
fails, because hub_port_debounce_be_connected() returns -ETIMEDOUT.

This means the port resume fails and khubd doesn't handle the USB device
disconnect.  This leaves the device listed in lsusb, and the port's
runtime_status will be permanently marked as "error".

Fix this by ignoring the return value of hub_port_debounce_be_connected.
Users can disconnect USB devices while the ports are powered off, and we
must be able to handle that.

This patch should be backported to kernels as old as 3.9, that
contain the commit ad493e5e "usb: add
usb port auto power off mechanism"
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The pm qos NO_POWER_OFF flag is checked twice during usb device suspend
to see if the usb port power off condition is met. This is redundant and
also will prevent the port from being powered off if the NO_POWER_OFF
flag is changed to 1 from 0 after the device was already suspended.

More detail in the following link.
	http://marc.info/?l=linux-usb&m=136543949130865&w=2

This patch should be backported to kernels as old as 3.7, that
contain the commit f7ac7787 "usb/acpi:
Use ACPI methods to power off ports."
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

The hub driver's usb_port_suspend() routine doesn't handle errors
related to Link Power Management properly.  It always returns failure,
it doesn't try to clean up the wakeup setting, (in the case of system
sleep) it doesn't try to go ahead with the port suspend regardless,
and it doesn't try to apply the new power-off mechanism.

This patch fixes these problems.

Note: Sarah fixed this patch to apply against 3.11, since the original
commit (4fae6f0f "USB: handle LPM errors
during device suspend correctly") called usb_disable_remote_wakeup,
which won't be added until 3.12.

This patch should be backported to kernels as old as 3.5, that
contain the commit 8306095f "USB:
Disable USB 3.0 LPM in critical sections.".  There will be merge
conflicts, since LTM wasn't added until 3.6.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Drivers supporting NAPI should use a NAPI-specific function for receiving
packets.  Hence netif_rx is changed to netif_receive_skb.

Furthermore netif_napi_del should be used in the probe and remove function
to clean up the NAPI resource information.

Thanks to Francois Romieu, David Shwatrz and Rami Rosen for their help on
this patch.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit f83331ba.

As the tests PPC64 (powernv platform) show, IOMMU pages are leaking
when transferring big amount of small packets (<=64 bytes),
"ping -f" and waiting for 15 seconds is the simplest way to confirm the bug.

Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Santosh Rastapur <santosh@chelsio.com>
Cc: Jay Fenlason <fenlason@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Divy Le ray <divy@chelsio.com>
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible for some versions of firmware to advertise capabilities that driver
is not ready to handle. This may lead to controller stall. Since the driver is
interested only in subset of flags, clearing the rest.
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure the USB control request is allocated separately from
containing structure to prevent potential memory corruption on
non-cache-coherent systems.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure serial DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure serial DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure port DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure serial DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to fail properly if the device is not accepted during attach
in order to avoid null-pointer derefs (of missing interface private
data) at disconnect or release.

Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The parallel-port code of the drivers used a stack allocated
control-request buffer for asynchronous (and possibly deferred) control
requests. This not only violates the no-DMA-from-stack requirement but
could also lead to corrupt control requests being submitted.

Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These devices tend to become unresponsive after S3
Signed-off-by: NOliver Neukum <oneukum@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The chipidea i.MX driver is split into two drivers. The ci_hdrc_imx driver
handles the chipidea cores and the usbmisc_imx driver handles the noncore
registers common to all chipidea cores (but SoC specific). Current flow is:

- usbmisc sets an ops pointer in the ci_hdrc_imx driver during probe
- ci_hdrc_imx checks if the pointer is valid during probe, if yes calls
  the functions in the ops pointer.
- usbmisc_imx calls back into the ci_hdrc_imx driver to get additional
  data

This is overly complicated and has problems if the drivers are compiled
as modules. In this case the usbmisc_imx driver can be unloaded even if
the ci_hdrc_imx driver still needs usbmisc functionality.

This patch changes this by letting the ci_hdrc_imx driver calling functions
from the usbmisc_imx driver. This way the symbol resolving during module
load makes sure the ci_hdrc_imx driver depends on the usbmisc_imx driver.

Also instead of letting the usbmisc_imx driver call back into the ci_hdrc_imx
driver, pass the needed data in the first place.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>