[ Upstream commit 5cd1c56c42beb6d228cc8d4373fdc5f5ec78a5ad ]

Add PCI ID for Intel Comet Lake PCH.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NSasha Levin (Microsoft) <sashal@kernel.org>

[ Upstream commit 5b277402 ]

Allow I2C_OMAP to be built for K3 platforms.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

Add Actions Semiconductor Owl family S900 I2C driver.
Signed-off-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This bus driver supports the GENI based i2c hardware controller in the
Qualcomm SOCs. The Qualcomm Generic Interface (GENI) is a programmable
module supporting a wide range of serial interfaces including I2C. The
driver supports FIFO mode and DMA mode of transfer and switches modes
dynamically depending on the size of the transfer.
Signed-off-by: NKarthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: NSagar Dharia <sdharia@codeaurora.org>
Signed-off-by: NGirish Mahadevan <girishm@codeaurora.org>
Reviewed-by: NDouglas Anderson <dianders@chromium.org>
Reviewed-by: NStephen Boyd <swboyd@chromium.org>
Tested-by: NStephen Boyd <swboyd@chromium.org>
[wsa: squashed the MAINTAINER addition and a RPM fix by Evan Green]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add register definitions for FSI-attached I2C master and functions to
access those registers over FSI. Add an FSI driver so that our I2C bus
is probed up during an FSI scan.
Signed-off-by: NEddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Intel Ice Lake has the same SMBus host controller than Intel Cannon
Lake. Add the PCI ID to the drivers list of supported devices.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
[jarkko.nikula@linux.intel.com: Add entries to Documentation and Kconfig]
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Make list of supported chipsets a little bit shorter by consolidating
names that belong to the same family.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The driver will not probe unless bq24190 is loaded, so
making it a dependency.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds slave support for I2C controller embedded in STM32F7 SoC
Signed-off-by: NM'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: NPierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.

Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.

This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: NMark Brown <broonie@kernel.org>
Acked-by: NRobin Murphy <robin.murphy@arm.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This is a cleaned up version of the I2C controller driver for
the Fujitsu F_I2C IP, which was never supported upstream, and
has now been incorporated into the Socionext SynQuacer SoC.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
[wsa: updated MAINTAINERS entry and removed two empty lines]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The blackfin architecture is getting removed, so the
twi driver can also be removed.
Acked-by: NAaron Wu <aaron.wu@analog.com>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Now that arch/metag/ has been removed, remove the METAG dependency from
the IMG SCB I2C device driver. The hardware is also present on MIPS SoCs
so the driver still has value.
Signed-off-by: NJames Hogan <jhogan@kernel.org>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Cc: linux-i2c@vger.kernel.org
Cc: linux-metag@vger.kernel.org

Commits adding PCI IDs for Intel Braswell and Kaby Lake PCH-H lacked the
respective Kconfig and Documentation/i2c/busses/i2c-i801 change. Add
them now.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add fault injection capabilities to the i2c-gpio driver. When connected
to another I2C bus, it can create unusual states which the other I2C bus
master driver needs to handle. Only for debugging!
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>

Add device-properties to make the bq24292i charger connected to
the bus get its input-current-limit from the fusb302 Type-C port
controller which is used on boards with the cht-wc PMIC,
as well as regulator_init_data for the 5V boost converter on
the bq24292i.

Since this means we now hook-up the bq24292i to the fusb302 Type-C port
controller add a check for the ACPI device which instantiates the fusb302.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add PCI ID for Intel Cedar Fork PCH.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds initial support for the STM32F7 I2C controller.
Signed-off-by: NM'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: NPierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add driver support for the Altera I2C Controller. The I2C
controller is soft IP for use in FPGAs.
Signed-off-by: NThor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Since the i2c driver of Spreadtrum can not be build as one module, thus
it should depend on CONFIG_I2C is build in.
Signed-off-by: NBaolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds the I2C controller driver for Spreadtrum SC9860 platform.
Signed-off-by: NBaolin Wang <baolin.wang@spreadtrum.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The Intel Cherry Trail Whiskey Cove PMIC does not contain a builtin
battery charger, instead boards with this PMIC use an external TI
bq24292i charger IC, which is connected to a SMBUS controller built into
the PMIC.

This commit adds an i2c-bus driver for the PMIC's builtin SMBUS
controller. The probe function for this i2c-bus will also register an
i2c-client for the TI bq24292i charger after the i2c-bus has been
registered.

Note that several device-properties are set on the client-device to
tell the bq24190 power-supply driver to integrate the Whiskey Cove PMIC
and e.g. use the PMIC's BC1.2 detection (through extcon) to determine
the maximum input current.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allow i2c-versatile to be enabled for ARM MPS platforms.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Only certain system configurations may use the I2C slave mode so let the
support be optional. This allow reducing module size if needed:

   text    data     bss     dec     hex filename
  10328    1336      16   11680    2da0 drivers/i2c/busses/i2c-designware-core.ko
   7222    1136       8    8366    20ae drivers/i2c/busses/i2c-designware-core.ko
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: NLuis Oliveira <lolivei@synopsys.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

- Changes in Kconfig to enable I2C_DESIGNWARE_SLAVE support
- Slave functions added to core library file
- Slave abort sources added to common source file
- New driver: i2c-designware-slave added
- Changes in the Makefile to compile the I2C_DESIGNWARE_SLAVE module
  when supported by the architecture.

All the SLAVE flow is added but it is not enabled via platform
driver.
Signed-off-by: NLuis Oliveira <lolivei@synopsys.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: made a function static and one-lined a message]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

0-DAY kernel test reports the following build issue on IA64 architecture
with allmodconfig.

   drivers/i2c/busses/i2c-zx2967.c: In function 'zx2967_i2c_writesb':
>> drivers/i2c/busses/i2c-zx2967.c:87:2: error: implicit declaration of function 'writesb' [-Werror=implicit-function-declaration]
     writesb(i2c->reg_base + reg, data, len);
     ^~~~~~~
   drivers/i2c/busses/i2c-zx2967.c: In function 'zx2967_i2c_readsb':
>> drivers/i2c/busses/i2c-zx2967.c:93:2: error: implicit declaration of function 'readsb' [-Werror=implicit-function-declaration]
     readsb(i2c->reg_base + reg, data, len);
     ^~~~~~
   cc1: some warnings being treated as errors

It's caused by that writesb/readsb are unavailable on IA64 architecture.
Let's drop COMPILE_TEST dependency to avoid the build issue.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds i2c controller driver for ZTE's zx2967 family.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: NJun Nie <jun.nie@linaro.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Added initial master support for Aspeed I2C controller. Supports
fourteen busses present in AST24XX and AST25XX BMC SoCs by Aspeed.
Signed-off-by: NBrendan Higgins <brendanhiggins@google.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Added SMBUS PCI Ids for SMBUS for Cannon Lake PCH.
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[jarkko.nikula@linux.intel.com: Add entries to Documentation and Kconfig.
Cover Cannon Lake-H too]
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

ARCH_VULCAN arm64 platform (for Broadcom Vulcan ARM64 processors) has
been discontinued. Cavium's ThunderX2 CN99XX (ARCH_THUNDER2) will be
the next revision of the platform.

Update compile dependencies and ACPI ID to reflect this change. There
is not need to retain ARCH_VULCAN since the Vulcan processor was never
in production and the config option will be removed soon.
Signed-off-by: NJayachandran C <jnair@caviumnetworks.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Enable the Tegra BPMP I2C adapter by default if the Tegra BPMP itself
is enabled. This adapter is used as the I2C interface for the PMIC on
the Tegra186 Jetson-TX2 platform.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add Tegra BPMP I2C driver. The BPMP is the boot and power management
processor embedded in Tegra SoCs. In newer SoC versions, access to one
of the I2C busses goes via the BPMP, requiring a different "proxy" I2C
driver that accesses the bus via the real I2C driver embedded in the
BPMP firmware.
Signed-off-by: NShardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Intel Gemini Lake has the same SMBus host controller than Intel Broxton.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds support for the STM32F4 I2C controller.
Signed-off-by: NM'boumba Cedric Madianga <cedric.madianga@gmail.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch allows Cadence I2C controller to be selected in systems using Cadence Xtensa processors.
Signed-off-by: NJan Kotas <jank@cadence.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds lpi2c bus driver to support new i.MX products
which use lpi2c instead of the old imx i2c.

The lpi2c can continue operating in stop mode when an appropriate
clock is available. It is also designed for low CPU overhead with
DMA offloading of FIFO register accesses.
Signed-off-by: NGao Pan <pandy.gao@nxp.com>
Reviewed-by: NFugang Duan <B38611@freescale.com>
Reviewed-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The Armada 3700 has two I2C controllers that is compliant with the I2C
Bus Specificiation 2.1, supports multi-master and different bus speed:
Standard mode (up to 100 KHz), Fast mode (up to 400 KHz),
High speed mode (up to 3.4 Mhz).

This IP block has a lot of similarity with the PXA, except some register
offsets and bitfield. This commits adds a basic support for this I2C
unit.
Signed-off-by: NRomain Perier <romain.perier@free-electrons.com>
Tested-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Device driver for Mellanox I2C controller logic, implemented in Lattice
CPLD device.
Device supports:
 - Master mode
 - One physical bus
 - Polling mode

The Kconfig currently controlling compilation of this code is:
drivers/i2c/busses/Kconfig:config I2C_MLXCPLD
Signed-off-by: NMichael Shych <michaelsh@mellanox.com>
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The i2c controller used by Freescales iMX processors is the same
hardware module used on Freescales ColdFire family of processors.

We can use the existing i2c-imx driver on ColdFire family members.
Modify the configuration to allow it to be selected when compiling
for ColdFire targets.
Signed-off-by: NGreg Ungerer <gerg@linux-m68k.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This driver should be buildable with ARCH_HISI,
because some of other HiSilicon SoCs also use it.
Signed-off-by: NRuqiang Ju <juruqiang@huawei.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>