commit 344c0152d878922365464b7140c74c2a5e073d99 upstream.

commit a6a9be92 ("selftests: firmware: return Kselftest Skip code
for skipped tests") by Shuah modified failures to return the special
error code of $ksft_skip (4). We have a corner case issue where we
*do* want to verify_reqs().

Cc: <stable@vger.kernel.org> # >= 4.18
Fixes: a6a9be92 ("selftests: firmware: return Kselftest Skip code for for skipped tests")
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7b0b644b9aa2de5032db0f468fddca091d0b7b90 upstream.

Current GPIO code in cp210x fails to take USB autosuspend into account,
making it practically impossible to use GPIOs with autosuspend enabled
without user configuration. Fix this like for ftdi_sio in a previous patch.
Tested on a CP2102N.
Signed-off-by: NKaroly Pados <pados@pados.hu>
Fixes: cf5276ce ("USB: serial: cp210x: Adding GPIO support for CP2105")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 82f844c22588bf47132c82faeda50b6db473162c upstream.

Make sure the receiver is powered (and booted) before enabling the
wakeup interrupt to avoid spurious interrupts due to a floating input.

Similarly, disable the interrupt before powering off on probe errors and
on unbind.

Fixes: d2efbbd1 ("gnss: add driver for sirfstar-based receivers")
Cc: stable <stable@vger.kernel.org>	# 4.19
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d90b88fd3653f1fb66ecc6571b860d5a5749fa56 upstream.

Stack unwinding is implemented incorrectly in xtensa get_wchan: instead
of extracting a0 and a1 registers from the spill location under the
stack pointer it extracts a word pointed to by the stack pointer and
subtracts 4 or 3 from it.

Cc: stable@vger.kernel.org
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d3d6a18d7d351cbcc9b33dbedf710e65f8ce1595 upstream.

wake_up_locked() may but does not have to be called with interrupts
disabled. Since the fuse filesystem calls wake_up_locked() without
disabling interrupts aio_poll_wake() may be called with interrupts
enabled. Since the kioctx.ctx_lock may be acquired from IRQ context,
all code that acquires that lock from thread context must disable
interrupts. Hence change the spin_trylock() call in aio_poll_wake()
into a spin_trylock_irqsave() call. This patch fixes the following
lockdep complaint:

=====================================================
WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
5.0.0-rc4-next-20190131 #23 Not tainted
-----------------------------------------------------
syz-executor2/13779 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
0000000098ac1230 (&fiq->waitq){+.+.}, at: spin_lock include/linux/spinlock.h:329 [inline]
0000000098ac1230 (&fiq->waitq){+.+.}, at: aio_poll fs/aio.c:1772 [inline]
0000000098ac1230 (&fiq->waitq){+.+.}, at: __io_submit_one fs/aio.c:1875 [inline]
0000000098ac1230 (&fiq->waitq){+.+.}, at: io_submit_one+0xedf/0x1cf0 fs/aio.c:1908

and this task is already holding:
000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: spin_lock_irq include/linux/spinlock.h:354 [inline]
000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: aio_poll fs/aio.c:1771 [inline]
000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: __io_submit_one fs/aio.c:1875 [inline]
000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: io_submit_one+0xeb6/0x1cf0 fs/aio.c:1908
which would create a new lock dependency:
 (&(&ctx->ctx_lock)->rlock){..-.} -> (&fiq->waitq){+.+.}

but this new dependency connects a SOFTIRQ-irq-safe lock:
 (&(&ctx->ctx_lock)->rlock){..-.}

... which became SOFTIRQ-irq-safe at:
  lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
  __raw_spin_lock_irq include/linux/spinlock_api_smp.h:128 [inline]
  _raw_spin_lock_irq+0x60/0x80 kernel/locking/spinlock.c:160
  spin_lock_irq include/linux/spinlock.h:354 [inline]
  free_ioctx_users+0x2d/0x4a0 fs/aio.c:610
  percpu_ref_put_many include/linux/percpu-refcount.h:285 [inline]
  percpu_ref_put include/linux/percpu-refcount.h:301 [inline]
  percpu_ref_call_confirm_rcu lib/percpu-refcount.c:123 [inline]
  percpu_ref_switch_to_atomic_rcu+0x3e7/0x520 lib/percpu-refcount.c:158
  __rcu_reclaim kernel/rcu/rcu.h:240 [inline]
  rcu_do_batch kernel/rcu/tree.c:2486 [inline]
  invoke_rcu_callbacks kernel/rcu/tree.c:2799 [inline]
  rcu_core+0x928/0x1390 kernel/rcu/tree.c:2780
  __do_softirq+0x266/0x95a kernel/softirq.c:292
  run_ksoftirqd kernel/softirq.c:654 [inline]
  run_ksoftirqd+0x8e/0x110 kernel/softirq.c:646
  smpboot_thread_fn+0x6ab/0xa10 kernel/smpboot.c:164
  kthread+0x357/0x430 kernel/kthread.c:247
  ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352

to a SOFTIRQ-irq-unsafe lock:
 (&fiq->waitq){+.+.}

... which became SOFTIRQ-irq-unsafe at:
...
  lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
  __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
  _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
  spin_lock include/linux/spinlock.h:329 [inline]
  flush_bg_queue+0x1f3/0x3c0 fs/fuse/dev.c:415
  fuse_request_queue_background+0x2d1/0x580 fs/fuse/dev.c:676
  fuse_request_send_background+0x58/0x120 fs/fuse/dev.c:687
  fuse_send_init fs/fuse/inode.c:989 [inline]
  fuse_fill_super+0x13bb/0x1730 fs/fuse/inode.c:1214
  mount_nodev+0x68/0x110 fs/super.c:1392
  fuse_mount+0x2d/0x40 fs/fuse/inode.c:1239
  legacy_get_tree+0xf2/0x200 fs/fs_context.c:590
  vfs_get_tree+0x123/0x450 fs/super.c:1481
  do_new_mount fs/namespace.c:2610 [inline]
  do_mount+0x1436/0x2c40 fs/namespace.c:2932
  ksys_mount+0xdb/0x150 fs/namespace.c:3148
  __do_sys_mount fs/namespace.c:3162 [inline]
  __se_sys_mount fs/namespace.c:3159 [inline]
  __x64_sys_mount+0xbe/0x150 fs/namespace.c:3159
  do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
  entry_SYSCALL_64_after_hwframe+0x49/0xbe

other info that might help us debug this:

 Possible interrupt unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&fiq->waitq);
                               local_irq_disable();
                               lock(&(&ctx->ctx_lock)->rlock);
                               lock(&fiq->waitq);
  <Interrupt>
    lock(&(&ctx->ctx_lock)->rlock);

 *** DEADLOCK ***

1 lock held by syz-executor2/13779:
 #0: 000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: spin_lock_irq include/linux/spinlock.h:354 [inline]
 #0: 000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: aio_poll fs/aio.c:1771 [inline]
 #0: 000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: __io_submit_one fs/aio.c:1875 [inline]
 #0: 000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: io_submit_one+0xeb6/0x1cf0 fs/aio.c:1908

the dependencies between SOFTIRQ-irq-safe lock and the holding lock:
-> (&(&ctx->ctx_lock)->rlock){..-.} {
   IN-SOFTIRQ-W at:
                    lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
                    __raw_spin_lock_irq include/linux/spinlock_api_smp.h:128 [inline]
                    _raw_spin_lock_irq+0x60/0x80 kernel/locking/spinlock.c:160
                    spin_lock_irq include/linux/spinlock.h:354 [inline]
                    free_ioctx_users+0x2d/0x4a0 fs/aio.c:610
                    percpu_ref_put_many include/linux/percpu-refcount.h:285 [inline]
                    percpu_ref_put include/linux/percpu-refcount.h:301 [inline]
                    percpu_ref_call_confirm_rcu lib/percpu-refcount.c:123 [inline]
                    percpu_ref_switch_to_atomic_rcu+0x3e7/0x520 lib/percpu-refcount.c:158
                    __rcu_reclaim kernel/rcu/rcu.h:240 [inline]
                    rcu_do_batch kernel/rcu/tree.c:2486 [inline]
                    invoke_rcu_callbacks kernel/rcu/tree.c:2799 [inline]
                    rcu_core+0x928/0x1390 kernel/rcu/tree.c:2780
                    __do_softirq+0x266/0x95a kernel/softirq.c:292
                    run_ksoftirqd kernel/softirq.c:654 [inline]
                    run_ksoftirqd+0x8e/0x110 kernel/softirq.c:646
                    smpboot_thread_fn+0x6ab/0xa10 kernel/smpboot.c:164
                    kthread+0x357/0x430 kernel/kthread.c:247
                    ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
   INITIAL USE at:
                   lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
                   __raw_spin_lock_irq include/linux/spinlock_api_smp.h:128 [inline]
                   _raw_spin_lock_irq+0x60/0x80 kernel/locking/spinlock.c:160
                   spin_lock_irq include/linux/spinlock.h:354 [inline]
                   __do_sys_io_cancel fs/aio.c:2052 [inline]
                   __se_sys_io_cancel fs/aio.c:2035 [inline]
                   __x64_sys_io_cancel+0xd5/0x5a0 fs/aio.c:2035
                   do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
                   entry_SYSCALL_64_after_hwframe+0x49/0xbe
 }
 ... key      at: [<ffffffff8a574140>] __key.52370+0x0/0x40
 ... acquired at:
   lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
   __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
   _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
   spin_lock include/linux/spinlock.h:329 [inline]
   aio_poll fs/aio.c:1772 [inline]
   __io_submit_one fs/aio.c:1875 [inline]
   io_submit_one+0xedf/0x1cf0 fs/aio.c:1908
   __do_sys_io_submit fs/aio.c:1953 [inline]
   __se_sys_io_submit fs/aio.c:1923 [inline]
   __x64_sys_io_submit+0x1bd/0x580 fs/aio.c:1923
   do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
   entry_SYSCALL_64_after_hwframe+0x49/0xbe

the dependencies between the lock to be acquired
 and SOFTIRQ-irq-unsafe lock:
-> (&fiq->waitq){+.+.} {
   HARDIRQ-ON-W at:
                    lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
                    __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
                    _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
                    spin_lock include/linux/spinlock.h:329 [inline]
                    flush_bg_queue+0x1f3/0x3c0 fs/fuse/dev.c:415
                    fuse_request_queue_background+0x2d1/0x580 fs/fuse/dev.c:676
                    fuse_request_send_background+0x58/0x120 fs/fuse/dev.c:687
                    fuse_send_init fs/fuse/inode.c:989 [inline]
                    fuse_fill_super+0x13bb/0x1730 fs/fuse/inode.c:1214
                    mount_nodev+0x68/0x110 fs/super.c:1392
                    fuse_mount+0x2d/0x40 fs/fuse/inode.c:1239
                    legacy_get_tree+0xf2/0x200 fs/fs_context.c:590
                    vfs_get_tree+0x123/0x450 fs/super.c:1481
                    do_new_mount fs/namespace.c:2610 [inline]
                    do_mount+0x1436/0x2c40 fs/namespace.c:2932
                    ksys_mount+0xdb/0x150 fs/namespace.c:3148
                    __do_sys_mount fs/namespace.c:3162 [inline]
                    __se_sys_mount fs/namespace.c:3159 [inline]
                    __x64_sys_mount+0xbe/0x150 fs/namespace.c:3159
                    do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
                    entry_SYSCALL_64_after_hwframe+0x49/0xbe
   SOFTIRQ-ON-W at:
                    lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
                    __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
                    _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
                    spin_lock include/linux/spinlock.h:329 [inline]
                    flush_bg_queue+0x1f3/0x3c0 fs/fuse/dev.c:415
                    fuse_request_queue_background+0x2d1/0x580 fs/fuse/dev.c:676
                    fuse_request_send_background+0x58/0x120 fs/fuse/dev.c:687
                    fuse_send_init fs/fuse/inode.c:989 [inline]
                    fuse_fill_super+0x13bb/0x1730 fs/fuse/inode.c:1214
                    mount_nodev+0x68/0x110 fs/super.c:1392
                    fuse_mount+0x2d/0x40 fs/fuse/inode.c:1239
                    legacy_get_tree+0xf2/0x200 fs/fs_context.c:590
                    vfs_get_tree+0x123/0x450 fs/super.c:1481
                    do_new_mount fs/namespace.c:2610 [inline]
                    do_mount+0x1436/0x2c40 fs/namespace.c:2932
                    ksys_mount+0xdb/0x150 fs/namespace.c:3148
                    __do_sys_mount fs/namespace.c:3162 [inline]
                    __se_sys_mount fs/namespace.c:3159 [inline]
                    __x64_sys_mount+0xbe/0x150 fs/namespace.c:3159
                    do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
                    entry_SYSCALL_64_after_hwframe+0x49/0xbe
   INITIAL USE at:
                   lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
                   __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
                   _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
                   spin_lock include/linux/spinlock.h:329 [inline]
                   flush_bg_queue+0x1f3/0x3c0 fs/fuse/dev.c:415
                   fuse_request_queue_background+0x2d1/0x580 fs/fuse/dev.c:676
                   fuse_request_send_background+0x58/0x120 fs/fuse/dev.c:687
                   fuse_send_init fs/fuse/inode.c:989 [inline]
                   fuse_fill_super+0x13bb/0x1730 fs/fuse/inode.c:1214
                   mount_nodev+0x68/0x110 fs/super.c:1392
                   fuse_mount+0x2d/0x40 fs/fuse/inode.c:1239
                   legacy_get_tree+0xf2/0x200 fs/fs_context.c:590
                   vfs_get_tree+0x123/0x450 fs/super.c:1481
                   do_new_mount fs/namespace.c:2610 [inline]
                   do_mount+0x1436/0x2c40 fs/namespace.c:2932
                   ksys_mount+0xdb/0x150 fs/namespace.c:3148
                   __do_sys_mount fs/namespace.c:3162 [inline]
                   __se_sys_mount fs/namespace.c:3159 [inline]
                   __x64_sys_mount+0xbe/0x150 fs/namespace.c:3159
                   do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
                   entry_SYSCALL_64_after_hwframe+0x49/0xbe
 }
 ... key      at: [<ffffffff8a60dec0>] __key.43450+0x0/0x40
 ... acquired at:
   lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
   __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
   _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
   spin_lock include/linux/spinlock.h:329 [inline]
   aio_poll fs/aio.c:1772 [inline]
   __io_submit_one fs/aio.c:1875 [inline]
   io_submit_one+0xedf/0x1cf0 fs/aio.c:1908
   __do_sys_io_submit fs/aio.c:1953 [inline]
   __se_sys_io_submit fs/aio.c:1923 [inline]
   __x64_sys_io_submit+0x1bd/0x580 fs/aio.c:1923
   do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
   entry_SYSCALL_64_after_hwframe+0x49/0xbe

stack backtrace:
CPU: 0 PID: 13779 Comm: syz-executor2 Not tainted 5.0.0-rc4-next-20190131 #23
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x172/0x1f0 lib/dump_stack.c:113
 print_bad_irq_dependency kernel/locking/lockdep.c:1573 [inline]
 check_usage.cold+0x60f/0x940 kernel/locking/lockdep.c:1605
 check_irq_usage kernel/locking/lockdep.c:1650 [inline]
 check_prev_add_irq kernel/locking/lockdep_states.h:8 [inline]
 check_prev_add kernel/locking/lockdep.c:1860 [inline]
 check_prevs_add kernel/locking/lockdep.c:1968 [inline]
 validate_chain kernel/locking/lockdep.c:2339 [inline]
 __lock_acquire+0x1f12/0x4790 kernel/locking/lockdep.c:3320
 lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
 _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
 spin_lock include/linux/spinlock.h:329 [inline]
 aio_poll fs/aio.c:1772 [inline]
 __io_submit_one fs/aio.c:1875 [inline]
 io_submit_one+0xedf/0x1cf0 fs/aio.c:1908
 __do_sys_io_submit fs/aio.c:1953 [inline]
 __se_sys_io_submit fs/aio.c:1923 [inline]
 __x64_sys_io_submit+0x1bd/0x580 fs/aio.c:1923
 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: <stable@vger.kernel.org>
Fixes: e8693bcf ("aio: allow direct aio poll comletions for keyed wakeups") # v4.19
Signed-off-by: NMiklos Szeredi <miklos@szeredi.hu>
[ bvanassche: added a comment ]
Reluctantly-Acked-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 72faa7a773ca59336f3c889e878de81445c5a85c upstream.

The irq_pages is the number of pages for irq stack, but not the
order which is needed by __get_free_pages().
We can use get_order() to calculate the accurate order.
Signed-off-by: NLiu Xiang <liu.xiang6@zte.com.cn>
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Fixes: fe8bd18f ("MIPS: Introduce irq_stack")
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d7ac3c6ef5d8ce14b6381d52eb7adafdd6c8bb3c upstream.

IndexCard is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.

This issue was detected with the help of Smatch:

drivers/char/applicom.c:418 ac_write() warn: potential spectre issue 'apbs' [r]
drivers/char/applicom.c:728 ac_ioctl() warn: potential spectre issue 'apbs' [r] (local cap)

Fix this by sanitizing IndexCard before using it to index apbs.

Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].

[1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/

Cc: stable@vger.kernel.org
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8fde481ef3674ae5ad0dbfef4df18ff507c5675a upstream.

This fix enables USB role feature on intel commercial nuc
platform which is based on Kabylake chipset.
Signed-off-by: NBalaji Manoharan <m.balaji@intel.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6a072128d262d2b98d31626906a96700d1fc11eb upstream.

Then tracing syscall exit event it is extremely useful to filter exit
codes equal to some negative value, to react only to required errors.
But negative numbers does not work:

[root@snorch sys_exit_read]# echo "ret == -1" > filter
bash: echo: write error: Invalid argument
[root@snorch sys_exit_read]# cat filter
ret == -1
        ^
parse_error: Invalid value (did you forget quotes)?

Similar thing happens when setting triggers.

These is a regression in v4.17 introduced by the commit mentioned below,
testing without these commit shows no problem with negative numbers.

Link: http://lkml.kernel.org/r/20180823102534.7642-1-ptikhomirov@virtuozzo.com

Cc: stable@vger.kernel.org
Fixes: 80765597 ("tracing: Rewrite filter logic to be simpler and faster")
Signed-off-by: NPavel Tikhomirov <ptikhomirov@virtuozzo.com>
Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6f913de3231e1d70a871135b38219da7810df218 upstream.

EFI systems do not necessarily provide a legacy ROM. If the ROM is missing
the memory is not mapped at all.

Trying to dereference values in the legacy ROM area leads to a crash on
Macbook Pro.

Only look for values in the legacy ROM area for non-EFI system.

Fixes: 3548e131 ("x86/boot/compressed/64: Find a place for 32-bit trampoline")
Reported-by: NPitam Mitra <pitamm@gmail.com>
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NBockjoo Kim <bockjoo@phys.ufl.edu>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190219075224.35058-1-kirill.shutemov@linux.intel.com
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202351Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0237199186e7a4aa5310741f0a6498a20c820fd7 upstream.

Some F17h models do not have CPB set in CPUID even though the CPU
supports it. Set the feature bit unconditionally on all F17h.

 [ bp: Rewrite commit message and patch. ]
Signed-off-by: NJiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Acked-by: NTom Lendacky <thomas.lendacky@amd.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sherry Hurwitz <sherry.hurwitz@amd.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20181120030018.5185-1-jiaxun.yang@flygoat.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a3df633a3c92bb96b06552c3f828d7c267774379 ]

Metadata pointer is only initialized for action TCA_TUNNEL_KEY_ACT_SET, but
it is unconditionally dereferenced in tunnel_key_init() error handler.
Verify that metadata pointer is not NULL before dereferencing it in
tunnel_key_init error handling code.

Fixes: ee28bb56 ("net/sched: fix memory leak in act_tunnel_key_init()")
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 6191da98062d25276a3b88fb2a94dcbcfb3ea65d ]

when act_skbedit was converted to use RCU in the data plane, we added an
error path, but we forgot to drop the action refcount in case of failure
during a 'replace' operation:

 # tc actions add action skbedit ptype otherhost pass index 100
 # tc action show action skbedit
 total acts 1

         action order 0: skbedit  ptype otherhost pass
          index 100 ref 1 bind 0
 # tc actions replace action skbedit ptype otherhost drop index 100
 RTNETLINK answers: Cannot allocate memory
 We have an error talking to the kernel
 # tc action show action skbedit
 total acts 1

         action order 0: skbedit  ptype otherhost pass
          index 100 ref 2 bind 0

Ensure we call tcf_idr_release(), in case 'params_new' allocation failed,
also when the action is being replaced.

Fixes: c749cdda ("net/sched: act_skbedit: don't use spinlock in the data path")
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 8f67c90ee9148eab3d2b4393c3cf76489b27f87c ]

After commit 4e8ddd7f ("net: sched: don't release reference on action
overwrite"), the error path of all actions was converted to drop refcount
also when the action was being overwritten. But we forgot act_ipt_init(),
in case allocation of 'tname' was not successful:

 # tc action add action xt -j LOG --log-prefix hello index 100
 tablename: mangle hook: NF_IP_POST_ROUTING
         target:  LOG level warning prefix "hello" index 100
 # tc action show action xt
 total acts 1

         action order 0: tablename: mangle  hook: NF_IP_POST_ROUTING
         target  LOG level warning prefix "hello"
         index 100 ref 1 bind 0
 # tc action replace action xt -j LOG --log-prefix world index 100
 tablename: mangle hook: NF_IP_POST_ROUTING
         target:  LOG level warning prefix "world" index 100
 RTNETLINK answers: Cannot allocate memory
 We have an error talking to the kernel
 # tc action show action xt
 total acts 1

         action order 0: tablename: mangle  hook: NF_IP_POST_ROUTING
         target  LOG level warning prefix "hello"
         index 100 ref 2 bind 0

Ensure we call tcf_idr_release(), in case 'tname' allocation failed, also
when the action is being replaced.

Fixes: 4e8ddd7f ("net: sched: don't release reference on action overwrite")
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ed8fe20205ac054bf585156709de3913d1890f30 ]

When debugging another issue I faced an interrupt storm in this
driver (88E6390, port 9 in SGMII mode), consisting of alternating
link-up / link-down interrupts. Analysis showed that the driver
wanted to set a cmode that was set already. But so far
mv88e6390x_port_set_cmode() doesn't check this and powers down
SERDES, what causes the link to break, and eventually results in
the described interrupt storm.

Fix this by checking whether the cmode actually changes. We want
that the very first call to mv88e6390x_port_set_cmode() always
configures the registers, therefore initialize port.cmode with
a value that is different from any supported cmode value.
We have to take care that we only init the ports cmode once
chip->info->num_ports is set.

v2:
- add small helper and init the number of actual ports only

Fixes: 364e9d77 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d235c48b40d399328585a68f3f9bf7cc3062d586 ]

Upon setting the cmode on 6390 and 6390X, the associated serdes
interfaces must be powered off/on.

Both 6390X and 6390 share code to do so, but it currently uses the 6390
specific helper mv88e6390_serdes_power() to disable and enable the
serdes interface.

This call will fail silently on 6390X when trying so set a 10G interface
such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
the lane number based on modes supported by the 6390, and returns 0 when
getting -ENODEV as a lane number.

Using mv88e6390x_serdes_power() should be safe here, since we explicitly
rule-out all ports but the 9 and 10, and because modes supported by 6390
ports 9 and 10 are a subset of those supported on 6390X.

This was tested on 6390X using RXAUI mode.

Fixes: 364e9d77 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a1fd1ad2552fad9e649eeb85fd79301e2880a886 ]

ip_route_input_rcu expects the original ingress device (e.g., for
proper multicast handling). The skb->dev can be changed by l3mdev_ip_rcv,
so dev needs to be saved prior to calling it. This was the behavior prior
to the listify changes.

Fixes: 5fa12739 ("net: ipv4: listify ip_rcv_finish")
Cc: Edward Cree <ecree@solarflare.com>
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit be48220edd48ca0d569782992840488a52373a24 ]

MPLS does not support nexthops with an MPLS address family.
Specifically, it does not handle RTA_GATEWAY attribute. Make it
clear by returning an error.

Fixes: 03c05665 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit e3818541b49fb88650ba339d33cc53e4095da5b3 ]

IPv6 currently does not support nexthops outside of the AF_INET6 family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:

  $ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
  $ ip ro ls
  ...
  2001:db8:2::/64 dev eth0 metric 1024 pref medium

Catch this and fail the route add:
  $ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
  Error: IPv6 does not support RTA_VIA attribute.

Fixes: 03c05665 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit b6e9e5df4ecf100f6a10ab2ade8e46d47a4b9779 ]

IPv4 currently does not support nexthops outside of the AF_INET family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:

  $ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
  $ ip ro ls
  ...
  172.16.1.0/24 dev eth0

Catch this and fail the route add:
  $ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
  Error: IPv4 does not support RTA_VIA attribute.

Fixes: 03c05665 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 3da1ed7ac398f34fff1694017a07054d69c5f5c5 ]

Extract IP options in cipso_v4_error and use __icmp_send.
Signed-off-by: NSergey Nazarov <s-nazarov@yandex.ru>
Acked-by: NPaul Moore <paul@paul-moore.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9ef6b42ad6fd7929dd1b6092cb02014e382c6a91 ]

Add __icmp_send function having ip_options struct parameter
Signed-off-by: NSergey Nazarov <s-nazarov@yandex.ru>
Reviewed-by: NPaul Moore <paul@paul-moore.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ecef67cb10db7b83b3b71c61dbb29aa070ab0112 ]

Replace set_current_state with __set_current_state since no memory
barrier is needed at this point.
Signed-off-by: NTimur Celik <mail@timurcelik.de>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 99e87f56b48f490fb16b6e0f74691c1e664dea95 ]

Zero-copy callback flag is not yet set on frag list skb at the moment
xenvif_handle_frag_list() returns -ENOMEM. This eventually results in
leaking grant ref mappings since xenvif_zerocopy_callback() is never
called for these fragments. Those eventually build up and cause Xen
to kill Dom0 as the slots get reused for new mappings:

"d0v0 Attempt to implicitly unmap a granted PTE c010000329fce005"

That behavior is observed under certain workloads where sudden spikes
of page cache writes coexist with active atomic skb allocations from
network traffic. Additionally, rework the logic to deal with frag_list
deallocation in a single place.
Signed-off-by: NPaul Durrant <paul.durrant@citrix.com>
Signed-off-by: NIgor Druzhinin <igor.druzhinin@citrix.com>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a2288d4e355992d369c50c45d017a85f6061ff71 ]

Occasionally, during the disconnection procedure on XenBus which
includes hash cache deinitialization there might be some packets
still in-flight on other processors. Handling of these packets includes
hashing and hash cache population that finally results in hash cache
data structure corruption.

In order to avoid this we prevent hashing of those packets if there
are no queues initialized. In that case RCU protection of queues guards
the hash cache as well.
Signed-off-by: NIgor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: NPaul Durrant <paul.durrant@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 71828b2240692cec0e68b8d867bc00e1745e7fae ]

This patch moves setting of the current state into the loop. Otherwise
the task may end up in a busy wait loop if none of the break conditions
are met.
Signed-off-by: NTimur Celik <mail@timurcelik.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit bfd07f3dd4f111b884d7922b37eb239280f83d8c ]

When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.

CPU-0                                | CPU-1
tipc_wait_for_cond()                 |
{                                    |
 // condition_ = !tsk->cong_link_cnt |
 while ((rc_ = !(condition_))) {     |
  ...                                |
  release_sock(sk_);                 |
  wait_woken();                      |
                                     | if (!sock_owned_by_user(sk))
                                     |  tipc_sk_filter_rcv()
                                     |  {
                                     |   ...
                                     |   tipc_sk_proto_rcv()
                                     |   {
                                     |    ...
                                     |    tsk->cong_link_cnt--;
                                     |    ...
                                     |    sk->sk_write_space(sk);
                                     |    ...
                                     |   }
                                     |   ...
                                     |  }
  sched_annotate_sleep();            |
  lock_sock(sk_);                    |
  remove_wait_queue();               |
 }                                   |
}                                    |

This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().
Acked-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NTung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ff7b11aa481f682e0e9711abfeb7d03f5cd612bf ]

Commit 9060cb719e61 ("net: crypto set sk to NULL when af_alg_release.")
fixed a use-after-free in sockfs_setattr() when an AF_ALG socket is
closed concurrently with fchownat().  However, it ignored that many
other proto_ops::release() methods don't set sock->sk to NULL and
therefore allow the same use-after-free:

    - base_sock_release
    - bnep_sock_release
    - cmtp_sock_release
    - data_sock_release
    - dn_release
    - hci_sock_release
    - hidp_sock_release
    - iucv_sock_release
    - l2cap_sock_release
    - llcp_sock_release
    - llc_ui_release
    - rawsock_release
    - rfcomm_sock_release
    - sco_sock_release
    - svc_release
    - vcc_release
    - x25_release

Rather than fixing all these and relying on every socket type to get
this right forever, just make __sock_release() set sock->sk to NULL
itself after calling proto_ops::release().

Reproducer that produces the KASAN splat when any of these socket types
are configured into the kernel:

    #include <pthread.h>
    #include <stdlib.h>
    #include <sys/socket.h>
    #include <unistd.h>

    pthread_t t;
    volatile int fd;

    void *close_thread(void *arg)
    {
        for (;;) {
            usleep(rand() % 100);
            close(fd);
        }
    }

    int main()
    {
        pthread_create(&t, NULL, close_thread, NULL);
        for (;;) {
            fd = socket(rand() % 50, rand() % 11, 0);
            fchownat(fd, "", 1000, 1000, 0x1000);
            close(fd);
        }
    }

Fixes: 86741ec2 ("net: core: Add a UID field to struct sock.")
Signed-off-by: NEric Biggers <ebiggers@google.com>
Acked-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 07f12b26e21ab359261bf75cfcb424fdc7daeb6d ]

If register_netdev() is failed to register sitn->fb_tunnel_dev,
it will go to err_reg_dev and forget to free netdev(sitn->fb_tunnel_dev).

BUG: memory leak
unreferenced object 0xffff888378daad00 (size 512):
  comm "syz-executor.1", pid 4006, jiffies 4295121142 (age 16.115s)
  hex dump (first 32 bytes):
    00 e6 ed c0 83 88 ff ff 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
backtrace:
    [<00000000d6dcb63e>] kvmalloc include/linux/mm.h:577 [inline]
    [<00000000d6dcb63e>] kvzalloc include/linux/mm.h:585 [inline]
    [<00000000d6dcb63e>] netif_alloc_netdev_queues net/core/dev.c:8380 [inline]
    [<00000000d6dcb63e>] alloc_netdev_mqs+0x600/0xcc0 net/core/dev.c:8970
    [<00000000867e172f>] sit_init_net+0x295/0xa40 net/ipv6/sit.c:1848
    [<00000000871019fa>] ops_init+0xad/0x3e0 net/core/net_namespace.c:129
    [<00000000319507f6>] setup_net+0x2ba/0x690 net/core/net_namespace.c:314
    [<0000000087db4f96>] copy_net_ns+0x1dc/0x330 net/core/net_namespace.c:437
    [<0000000057efc651>] create_new_namespaces+0x382/0x730 kernel/nsproxy.c:107
    [<00000000676f83de>] copy_namespaces+0x2ed/0x3d0 kernel/nsproxy.c:165
    [<0000000030b74bac>] copy_process.part.27+0x231e/0x6db0 kernel/fork.c:1919
    [<00000000fff78746>] copy_process kernel/fork.c:1713 [inline]
    [<00000000fff78746>] _do_fork+0x1bc/0xe90 kernel/fork.c:2224
    [<000000001c2e0d1c>] do_syscall_64+0xc8/0x580 arch/x86/entry/common.c:290
    [<00000000ec48bd44>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
    [<0000000039acff8a>] 0xffffffffffffffff
Signed-off-by: NMao Wenan <maowenan@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d25ed413d5e51644e18f66e34eec049f17a7abcb ]

When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.

v2:
- use right function name in subject
v3:
- initialize additional fields

Fixes: 9525ae83 ("phylink: add phylink infrastructure")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 232ba3a51cc224b339c7114888ed7f0d4d95695e ]

With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.

DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).

END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.

WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
   register 2, prior to connecting the cable or prior to setting the
   Restart Auto-negotiation bit in register 0h. The MMD registers are
   accessed via the indirect access registers Dh and Eh, or via the Micrel
   EthUtil utility as shown here:
   . if using the EthUtil utility (usually with a Micrel KSZ8061
     Evaluation Board), type the following commands:
     > address 1
     > mmd 1
     > iw 2 b61a
   . Alternatively, write the following registers to write to the
     indirect MMD register:
     Write register Dh, data 0001h
     Write register Eh, data 0002h
     Write register Dh, data 4001h
     Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
   either by the strapping option, or by clearing bit 12 in register 0h.
   Care must be taken to ensure that the KSZ8061 and the link partner
   will link with the same speed and duplex. Note that the KSZ8061
   defaults to full-duplex when auto-negotiation is off, but other
   devices may default to half-duplex in the event of failed
   auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
   or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
   be recovered by setting the Restart Auto-Negotiation bit in
   register 0h, or by resetting or power cycling the device. Reset may
   be either hardware reset or software reset (register 0h, bit 15).

PLAN
This errata will not be corrected in the future revision.

Fixes: 7ab59dc1 ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: NAlexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: NRajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 58bdd544e2933a21a51eecf17c3f5f94038261b5 ]

KASAN report this:

BUG: KASAN: null-ptr-deref in nfc_llcp_build_gb+0x37f/0x540 [nfc]
Read of size 3 at addr 0000000000000000 by task syz-executor.0/5401

CPU: 0 PID: 5401 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0xfa/0x1ce lib/dump_stack.c:113
 kasan_report+0x171/0x18d mm/kasan/report.c:321
 memcpy+0x1f/0x50 mm/kasan/common.c:130
 nfc_llcp_build_gb+0x37f/0x540 [nfc]
 nfc_llcp_register_device+0x6eb/0xb50 [nfc]
 nfc_register_device+0x50/0x1d0 [nfc]
 nfcsim_device_new+0x394/0x67d [nfcsim]
 ? 0xffffffffc1080000
 nfcsim_init+0x6b/0x1000 [nfcsim]
 do_one_initcall+0xfa/0x5ca init/main.c:887
 do_init_module+0x204/0x5f6 kernel/module.c:3460
 load_module+0x66b2/0x8570 kernel/module.c:3808
 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f9cb79dcc58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000020000280 RDI: 0000000000000003
RBP: 00007f9cb79dcc70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f9cb79dd6bc
R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004

nfc_llcp_build_tlv will return NULL on fails, caller should check it,
otherwise will trigger a NULL dereference.
Reported-by: NHulk Robot <hulkci@huawei.com>
Fixes: eda21f16 ("NFC: Set MIU and RW values from CONNECT and CC LLCP frames")
Fixes: d646960f ("NFC: Initial LLCP support")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 5845f706388a4cde0f6b80f9e5d33527e942b7d9 ]

It can be reproduced by following steps:
1. virtio_net NIC is configured with gso/tso on
2. configure nginx as http server with an index file bigger than 1M bytes
3. use tc netem to produce duplicate packets and delay:
   tc qdisc add dev eth0 root netem delay 100ms 10ms 30% duplicate 90%
4. continually curl the nginx http server to get index file on client
5. BUG_ON is seen quickly

[10258690.371129] kernel BUG at net/core/skbuff.c:4028!
[10258690.371748] invalid opcode: 0000 [#1] SMP PTI
[10258690.372094] CPU: 5 PID: 0 Comm: swapper/5 Tainted: G        W         5.0.0-rc6 #2
[10258690.372094] RSP: 0018:ffffa05797b43da0 EFLAGS: 00010202
[10258690.372094] RBP: 00000000000005ea R08: 0000000000000000 R09: 00000000000005ea
[10258690.372094] R10: ffffa0579334d800 R11: 00000000000002c0 R12: 0000000000000002
[10258690.372094] R13: 0000000000000000 R14: ffffa05793122900 R15: ffffa0578f7cb028
[10258690.372094] FS:  0000000000000000(0000) GS:ffffa05797b40000(0000) knlGS:0000000000000000
[10258690.372094] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[10258690.372094] CR2: 00007f1a6dc00868 CR3: 000000001000e000 CR4: 00000000000006e0
[10258690.372094] Call Trace:
[10258690.372094]  <IRQ>
[10258690.372094]  skb_to_sgvec+0x11/0x40
[10258690.372094]  start_xmit+0x38c/0x520 [virtio_net]
[10258690.372094]  dev_hard_start_xmit+0x9b/0x200
[10258690.372094]  sch_direct_xmit+0xff/0x260
[10258690.372094]  __qdisc_run+0x15e/0x4e0
[10258690.372094]  net_tx_action+0x137/0x210
[10258690.372094]  __do_softirq+0xd6/0x2a9
[10258690.372094]  irq_exit+0xde/0xf0
[10258690.372094]  smp_apic_timer_interrupt+0x74/0x140
[10258690.372094]  apic_timer_interrupt+0xf/0x20
[10258690.372094]  </IRQ>

In __skb_to_sgvec(), the skb->len is not equal to the sum of the skb's
linear data size and nonlinear data size, thus BUG_ON triggered.
Because the skb is cloned and a part of nonlinear data is split off.

Duplicate packet is cloned in netem_enqueue() and may be delayed
some time in qdisc. When qdisc len reached the limit and returns
NET_XMIT_DROP, the skb will be retransmit later in write queue.
the skb will be fragmented by tso_fragment(), the limit size
that depends on cwnd and mss decrease, the skb's nonlinear
data will be split off. The length of the skb cloned by netem
will not be updated. When we use virtio_net NIC and invoke skb_to_sgvec(),
the BUG_ON trigger.

To fix it, netem returns NET_XMIT_SUCCESS to upper stack
when it clones a duplicate packet.

Fixes: 35d889d1 ("sch_netem: fix skb leak in netem_enqueue()")
Signed-off-by: NSheng Lan <lansheng@huawei.com>
Reported-by: NQin Ji <jiqin.ji@huawei.com>
Suggested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 5578de4834fe0f2a34fedc7374be691443396d1f ]

There are two array out-of-bounds memory accesses, one in
cipso_v4_map_lvl_valid(), the other in netlbl_bitmap_walk().  Both
errors are embarassingly simple, and the fixes are straightforward.

As a FYI for anyone backporting this patch to kernels prior to v4.8,
you'll want to apply the netlbl_bitmap_walk() patch to
cipso_v4_bitmap_walk() as netlbl_bitmap_walk() doesn't exist before
Linux v4.8.
Reported-by: NJann Horn <jannh@google.com>
Fixes: 446fda4f ("[NetLabel]: CIPSOv4 engine")
Fixes: 3faa8f98 ("netlabel: Move bitmap manipulation functions to the NetLabel core.")
Signed-off-by: NPaul Moore <paul@paul-moore.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 6e46e2d821bb22b285ae8187959096b65d063b0d ]

The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined.  Fix
the combing, which wrongly worked on u16's.

Fixes: 80c4627b ("dsa: mv88x6xxx: Refactor getting a single statistic")
Reported-by: NChris Healy <Chris.Healy@zii.aero>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a6da21bb0eae459a375d5bd48baed821d14301d0 ]

Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.

Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c39 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 90490ef7269906423a1c1b917fc24be8b1602658 ]

It has been observed that tx queue stalls while downloading
from certain web sites (example www.speedtest.net)

The cause has been tracked down to a corner case where
dma descriptors where not setup properly. And there for a tx
completion interrupt was not signaled.

This fix corrects the problem by properly marking the end of
a multi descriptor transmission.

Fixes: 23f0703c ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 5e1a99eae84999a2536f50a0beaf5d5262337f40 ]

For ip rules, we need to use 'ipproto ipv6-icmp' to match ICMPv6 headers.
But for ip -6 route, currently we only support tcp, udp and icmp.

Add ICMPv6 support so we can match ipv6-icmp rules for route lookup.

v2: As David Ahern and Sabrina Dubroca suggested, Add an argument to
rtm_getroute_parse_ip_proto() to handle ICMP/ICMPv6 with different family.
Reported-by: NJianlin Shi <jishi@redhat.com>
Fixes: eacb9384 ("ipv6: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: NHangbin Liu <liuhangbin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit bf48648d650db1146b75b9bd358502431e86cf4f ]

Incoming packets may have IP header checksum verified by the host.
They may not have IP header checksum computed after coalescing.
This patch re-compute the checksum when necessary, otherwise the
packets may be dropped, because Linux network stack always checks it.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit cf1c9ccba7308e48a68fa77f476287d9d614e4c7 ]

When IPv6 is compiled but disabled at runtime, geneve_sock_add returns
-EAFNOSUPPORT. For metadata based tunnels, this causes failure of the whole
operation of bringing up the tunnel.

Ignore failure of IPv6 socket creation for metadata based tunnels caused by
IPv6 not being available.

This is the same fix as what commit d074bf96 ("vxlan: correctly handle
ipv6.disable module parameter") is doing for vxlan.

Note there's also commit c0a47e44c098 ("geneve: should not call rt6_lookup()
when ipv6 was disabled") which fixes a similar issue but for regular
tunnels, while this patch is needed for metadata based tunnels.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>