- 15 2月, 2007 7 次提交
-
-
由 Tim Schmielau 提交于
After Al Viro (finally) succeeded in removing the sched.h #include in module.h recently, it makes sense again to remove other superfluous sched.h includes. There are quite a lot of files which include it but don't actually need anything defined in there. Presumably these includes were once needed for macros that used to live in sched.h, but moved to other header files in the course of cleaning it up. To ease the pain, this time I did not fiddle with any header files and only removed #includes from .c-files, which tend to cause less trouble. Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha, arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig, allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all configs in arch/arm/configs on arm. I also checked that no new warnings were introduced by the patch (actually, some warnings are removed that were emitted by unnecessarily included header files). Signed-off-by: NTim Schmielau <tim@physik3.uni-rostock.de> Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Haavard Skinnemoen 提交于
Driver for the Atmel on-chip SPI master controller. Tested primarily on AVR32/AT32AP7000/ATSTK1000 using mtd_dataflash and the jffs2 filesystem. Should also work fine on various AT91 ARM-based chips like AT91SAM926x and AT91RM9200. Hardware documentation can be found in the AT32AP7000 data sheet, or its AT91 siblings, which can be downloaded from http://www.atmel.com/dyn/products/datasheets.asp?family_id=682Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Vitaly Wool 提交于
Add UART support for PNX8330/8550/8950 Philips MIPS-based SoCs. Signed-off-by: NVitaly Wool <vitalywool@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Burman Yan 提交于
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 George G. Davis 提交于
Since serial devices are powered down when not in use and some of those devices cannot be accessed when powered down, we need to enable power around calls to get_mcrtl() when dumping port state via uart_line_info(). This resolves hangs observed on some machines while reading serial device registers when a port is powered off. Signed-off-by: NGeorge G. Davis <gdavis@mvista.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Bjorn Helgaas 提交于
Return failure immediately, so we don't have to test it twice. Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com> Cc: Adam Belay <ambx1@neo.rr.com> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alex Williamson 提交于
The patch below works around a minor bug found in the UART of the remote management card used in many HP ia64 and parisc servers (aka the Diva UARTs). The problem is that the UART does not reassert the THRE interrupt if it has been previously cleared and the IIR THRI bit is re-enabled. This can produce a very annoying failure mode when used as a serial console, allowing a boot/reboot to hang indefinitely until an RX interrupt kicks it into working again (ie. an unattended reboot could stall). To solve this problem, a backup timer is introduced that runs alongside the standard interrupt driven mechanism. This timer wakes up periodically, checks for a hang condition and gets characters moving again. This backup mechanism is only enabled if the UART is detected as having this problem, so systems without these UARTs will have no additional overhead. This version of the patch incorporates previous comments from Pavel and removes races in the bug detection code. The test is now done before the irq linking to prevent races with interrupt handler clearing the THRE interrupt. Short delays and syncs are also added to ensure the device is able to update register state before the result is tested. Aristeu says: this was tested on the following HP machines and solved the problem: rx2600, rx2620, rx1600 and rx1620s. hpa says: I have seen this same bug in soft UART IP from "a major vendor." Signed-off-by: NAlex Williamson <alex.williamson@hp.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Russell King <rmk@arm.linux.org.uk> Acked-by: NAristeu Sergio Rozanski Filho <aris@cathedrallabs.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 14 2月, 2007 26 次提交
-
-
由 Arnd Bergmann 提交于
This can be used for serial ports that are connected to an OF platform bus but are not autodetected by the lecacy serial support. It will automatically take over devices that come from the legacy serial detection, which usually is only one device. In some cases, rtas may be set up to use the serial port in the firmware, which allows easier debugging before probing the serial ports. In this case, the "used-by-rtas" property must be set by the firmware. This patch also adds code to the legacy serial driver to check for this. Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Eric W. Biederman 提交于
Somewhere in the rewrite of the work queues my cleanup of SAK handling got broken. Maybe I didn't retest it properly or possibly the API was changing so fast I missed something. Regardless currently triggering a SAK now generates an ugly BUG_ON and kills the kernel. Thanks to Alexey Dobriyan <adobriyan@openvz.org> for spotting this. This modifies the use of SAK_work to initialize it when the data structure it resides in is initialized, and to simply call schedule_work when we need to generate a SAK. I update both data structures that have a SAK_work member for consistency. All of the old PREPARE_WORK calls that are now gone. If we call schedule_work again before it has processed it has generated the first SAK it will simply ignore the duplicate schedule_work request. Signed-off-by: NEric W. Biederman <ebiederm@xmission.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jean Delvare 提交于
Stop using i2c_adapter.class_dev, as it is going to be removed soon. Luckily, there are only 4 RTC drivers affected. Signed-off-by: NJean Delvare <khali@linux-fr.org> Cc: Alessandro Zummo <a.zummo@towertech.it>
-
由 Jean Delvare 提交于
Now that the i2c_adapter migration plan changed and we are going to keep i2c_adapter.dev, it's no longer that urgent to add a proper device to all i2c_adapter drivers. Thus is seems resonable to degrade the warning asking authors to migrate their driver to a debug message. Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Jean Delvare 提交于
Declare the parent device of i2c_adapter devices each time we can easily do so. It makes the i2c_adapter appear at the right place in the device tree, rather than as a platform device. Signed-off-by: NJean Delvare <khali@linux-fr.org> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Len Brown <len.brown@intel.com> Cc: Jordan Crouse <jordan.crouse@amd.com> Cc: Jody McIntyre <scjody@modernduck.com> Cc: Stefan Richter <stefanr@s5r6.in-berlin.de> Cc: v4l-dvb-maintainer@linuxtv.org Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
-
由 Olof Johansson 提交于
New driver for the PA Semi SMBus interfaces. Signed-off-by: NOlof Johansson <olof@lixom.net> Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Jean Delvare 提交于
Proposed cleanups to the i2c-amd8111 SMBus driver: * Fold long lines. * Add an explicit mask when writing the low byte of a word. * Use I2C_SMBUS_BLOCK_MAX instead of hardcoding 32. * Discard extra blank lines. * Use boolean not instead of bitwise not for bit tests, it's clearer. * Return -EBUSY rather than -1 on I/O resource conflict. * Fix a race on device registration, initialization should be done before the bus is registered. Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Jonathan McDowell 提交于
This simple patch adds support to i2c-parport for the One For All remote JP1 parallel port interfaces which can be found detailed at: http://www.hifi-remote.com/jp1/hardware.shtml These allow access to the internal configuration EEPROM on various remote controls and there are a variety of Windows tools that make use of this hardware. I have tested this patch with the "simple" parallel port device and a One For All URC-7562 and confirmed that the data read using the eeprom i2c driver matches that returned by the Windows "IR" JP1 tool. Signed-off-by: NJonathan McDowell <noodles@earth.li> Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Jean Delvare 提交于
We do not have any documentation for the CX700, but it was reported to work fine. Thanks to Claas Langbehn for testing. Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Stephen Hemminger 提交于
IDs have been defined but not used by most of the I2C adapters. By having a unique ID, clients can check for correct connection during probe. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 David Brownell 提交于
Driver model updates for the I2C core: - Add new suspend(), resume(), and shutdown() methods. Use them in the standard driver model style; document them. - Minor doc updates to highlight zero-initialized fields in drivers, and the driver model accessors for "clientdata". If any i2c drivers were previously using the old suspend/resume calls in "struct driver", they were getting warning messages ... and will now no longer work. Other than that, this patch changes no behaviors; and it lets I2C drivers use conventional PM and shutdown support. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Jean Delvare 提交于
i2c-core and i2c-isa use completions without including <linux/completion.h>. Fix it. i2c-powermac includes <linux/completion.h> but doesn't use any completion. Fix it. Signed-off-by: NJean Delvare <khali@linux-fr.org> Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Cc: David Brownell <david-b@pacbell.net>
-
由 Jean Delvare 提交于
Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Jean Delvare 提交于
Add support for the ATI SB600 SMBus controller. Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Jean Delvare 提交于
Signed-off-by: NJean Delvare <khali@linux-fr.org> Cc: Hans-Frieder Vogt <hfvogt@gmx.net>
-
由 David Brownell 提交于
Remove a superfluous initialization from the vt8231 hwmon driver; the i2c core does this, and the source field will be vanishing soon. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Jean Delvare 提交于
The i2c-ali1563 initialization looks quite broken to me: * If the I/O space isn't enabled, we forcibly set 3 bits in the PCI configuration space instead of just the one enabling the I/O space. * After that we pretend to check if the write worked, but we don't actually read the new value from the register. * It's probably not a good idea to enable the I/O space if no base address has been set. So I propose the following changes to that part of the driver: * Merge ali1563_enable() into ali1563_setup(). * Check the base address before the I/O space enabled bit. Signed-off-by: NJean Delvare <khali@linux-fr.org> Acked-by: NRudolf Marek <r.marek@assembler.cz>
-
由 Jean Delvare 提交于
Improve the status messages printed by the i2c-ali1563 driver. Signed-off-by: NJean Delvare <khali@linux-fr.org> Cc: Rudolf Marek <r.marek@assembler.cz>
-
由 Michael Chan 提交于
Update version to 3.73. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Print the most useful information during tx timeout to help debug. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Set DMA read watermark to 4 on 5703 in PCIX mode. This is needed to prevent some tx timeouts. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
This fixes the following problem: http://bugzilla.kernel.org/show_bug.cgi?id=7969 The MSI state needs to be saved during suspend. PCI state saved during tg3_init_one() does not contain valid MSI state because MSI hasn't been enabled. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 2月, 2007 7 次提交
-
-
由 Grant Likely 提交于
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Olaf Hering 提交于
/proc/pmu/info contains AC Power: 0 when booting without battery. Force AC Power, it will be updated whenever the battery state changes. Signed-off-by: NOlaf Hering <olaf@aepfle.de> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Olaf Hering 提交于
Move all the initialized variables to bss. Mark a version string as const. Signed-off-by: NOlaf Hering <olaf@aepfle.de> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Michael S. Tsirkin 提交于
Speed up memory registration by filling in MTTs directly when the CPU can write directly to the whole table (all mem-free cards, and to Tavor mode on 64-bit systems with the patch I posted earlier). This reduces the number of FW commands needed to register an MR by at least a factor of 2 and speeds up memory registration significantly. Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Michael S. Tsirkin 提交于
For Tavor, we currently reserve separate MPT and MTT space for FMRs to avoid abusing the vmalloc space on 32 bit kernels. No such problem exists on 64 bit kernels so let's not do it there. This way we have a shared pool for MR and FMR resources, used on demand. This will also make it possible to write MTTs for regular regions directly from driver. Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Michael S. Tsirkin 提交于
We allocate the MTT table with alloc_pages() and then do pci_map_sg(), so we must call pci_dma_sync_sg() after the CPU writes to the MTT table. This works since the device will never write MTTs on mem-free HCAs, once we get rid of the use of the WRITE_MTT firmware command. This change is needed to make that work, and is an improvement for now, since it gives FMRs a chance at working. For MPTs, both the device and CPU might write there, so we must allocate DMA coherent memory for these. Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Michael S. Tsirkin 提交于
MTTs are allocated in non-cache-coherent memory, so we must give reserved MTTs their own cache line, to prevent both device and CPU from writing into the same cache line at the same time. Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-