Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 05 3月, 2015 2 次提交
    • N
      bcm63xx_enet: fix poll callback. · cd33ccf5
      由 Nicolas Schichan 提交于 
      In case there was some tx buffer reclaimed and not enough rx packets
to consume the whole budget, napi_complete would not be called and
interrupts would be kept disabled, effectively resulting in the
network core never to call the poll callback again and no rx/tx
interrupts to be fired either.

Fix that by only accounting the rx work done in the poll callback.
Signed-off-by: NNicolas Schichan <nschichan@freebox.fr>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      cd33ccf5
    • A
      stmmac: check IRQ availability early on probe · 8f02d8da
      由 Alexey Brodkin 提交于 
      Currently we're getting IRQs after lots of resources are already
allocated:
 * netdev
 * clocks
 * MDIO bus
Also HW gets initialized by the time when checking IRQs as well.

Now there's a possibility for master interrupt controller to be not
probed yet. This will lead to exit from GMAC probe routine with "-
EPROBE_DEFER" and so deferred probe will hapen later on.

But since we exited the first GMAC probe without release of all
allocated resources there could be conflicts on subsequent probes.

For example this is what happens for me:
 --->8---
 stmmaceth e0018000.ethernet: no reset control found
 stmmac - user ID: 0x10, Synopsys ID: 0x37
  Ring mode enabled
  DMA HW capability register supported
  Normal descriptors
  RX Checksum Offload Engine supported (type 2)
  TX Checksum insertion supported
  Enable RX Mitigation via HW Watchdog Timer
 libphy: stmmac: probed
 eth0: PHY ID 20005c7a at 1 IRQ POLL (stmmac-0:01) active
 platform e0018000.ethernet: Driver stmmaceth requests probe deferral
 ...
 ...
 ...
 stmmaceth e0018000.ethernet: no reset control found
 stmmac - user ID: 0x10, Synopsys ID: 0x37
  Ring mode enabled
  DMA HW capability register supported
  Normal descriptors
  RX Checksum Offload Engine supported (type 2)
  TX Checksum insertion supported
  Enable RX Mitigation via HW Watchdog Timer
 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 6 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x4e/0x68()
 sysfs: cannot create duplicate filename
'/devices/platform/axs10x_mb/e0018000.ethernet/mdio_bus/stmmac-0'
 CPU: 0 PID: 6 Comm: kworker/u2:0 Not tainted 4.0.0-rc1-next-20150303+#8
 Workqueue: deferwq deferred_probe_work_func

 Stack Trace:
  arc_unwind_core+0xb8/0x114
  warn_slowpath_common+0x5a/0x8c
  warn_slowpath_fmt+0x2e/0x38
  sysfs_warn_dup+0x4e/0x68
  sysfs_create_dir_ns+0x98/0xa0
  kobject_add_internal+0x8c/0x2e8
  kobject_add+0x4a/0x8c
  device_add+0xc6/0x448
  mdiobus_register+0x6c/0x164
  stmmac_mdio_register+0x112/0x264
  stmmac_dvr_probe+0x6c0/0x85c
  stmmac_pltfr_probe+0x2e4/0x50c
  platform_drv_probe+0x26/0x5c
  really_probe+0x76/0x1dc
  bus_for_each_drv+0x42/0x7c
  device_attach+0x64/0x6c
  bus_probe_device+0x74/0xa4
  deferred_probe_work_func+0x50/0x84
  process_one_work+0xf8/0x2cc
  worker_thread+0x110/0x478
  kthread+0x8a/0x9c
  ret_from_fork+0x14/0x18
 ---[ end trace a2dfaa7d630c8be1 ]---
 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 6 at lib/kobject.c:240
kobject_add_internal+0x218/0x2e8()
 kobject_add_internal failed for stmmac-0 with -EEXIST, don't try to
register things with the same name in the same di.
 CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G        W
4.0.0-rc1-next-20150303+ #8
 Workqueue: deferwq deferred_probe_work_func

 Stack Trace:
  arc_unwind_core+0xb8/0x114
  warn_slowpath_common+0x5a/0x8c
  warn_slowpath_fmt+0x2e/0x38
  kobject_add_internal+0x218/0x2e8
  kobject_add+0x4a/0x8c
  device_add+0xc6/0x448
  mdiobus_register+0x6c/0x164
  stmmac_mdio_register+0x112/0x264
  stmmac_dvr_probe+0x6c0/0x85c
  stmmac_pltfr_probe+0x2e4/0x50c
  platform_drv_probe+0x26/0x5c
  really_probe+0x76/0x1dc
  bus_for_each_drv+0x42/0x7c
  device_attach+0x64/0x6c
  bus_probe_device+0x74/0xa4
  deferred_probe_work_func+0x50/0x84
  process_one_work+0xf8/0x2cc
  worker_thread+0x110/0x478
  kthread+0x8a/0x9c
  ret_from_fork+0x14/0x18
 ---[ end trace a2dfaa7d630c8be2 ]---
 libphy: mii_bus stmmac-0 failed to register
 : Cannot register as MDIO bus
 stmmac_pltfr_probe: main driver probe failed
 stmmaceth: probe of e0018000.ethernet failed with error -22
 --->8---

Essential fix is to check for IRQs availability as early as possible and
then safely go to deferred probe if IRQs are not there yet.
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8f02d8da
  3. 04 3月, 2015 2 次提交
  5. 03 3月, 2015 6 次提交
  7. 02 3月, 2015 11 次提交
  9. 01 3月, 2015 6 次提交
    • G
      sh_eth: Fix lost MAC address on kexec · a14c7d15
      由 Geert Uytterhoeven 提交于 
      Commit 740c7f31 ("sh_eth: Ensure DMA engines are stopped before
freeing buffers") added a call to sh_eth_reset() to the
sh_eth_set_ringparam() and sh_eth_close() paths.

However, setting the software reset bit(s) in the EDMR register resets
the MAC Address Registers to zero. Hence after kexec, the new kernel
doesn't detect a valid MAC address and assigns a random MAC address,
breaking DHCP.

Set the MAC address again after the reset in sh_eth_dev_exit() to fix
this.

Tested on r8a7740/armadillo (GETHER) and r8a7791/koelsch (FAST_RCAR).

Fixes: 740c7f31 ("sh_eth: Ensure DMA engines are stopped before freeing buffers")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a14c7d15
    • J
      net: bcmgenet: fix throughtput regression · 4092e6ac
      由 Jaedon Shin 提交于 
      This patch adds bcmgenet_tx_poll for the tx_rings. This can reduce the
interrupt load and send xmit in network stack on time. This also
separated for the completion of tx_ring16 from bcmgenet_poll.

The bcmgenet_tx_reclaim of tx_ring[{0,1,2,3}] operative by an interrupt
is to be not more than a certain number TxBDs. It is caused by too
slowly reclaiming the transmitted skb. Therefore, performance
degradation of xmit after 605ad7f1 ("tcp: refine TSO autosizing").
Signed-off-by: NJaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4092e6ac
    • E
      macvtap: make sure neighbour code can push ethernet header · 2f1d8b9e
      由 Eric Dumazet 提交于 
      Brian reported crashes using IPv6 traffic with macvtap/veth combo.

I tracked the crashes in neigh_hh_output()

-> memcpy(skb->data - HH_DATA_MOD, hh->hh_data, HH_DATA_MOD);

Neighbour code assumes headroom to push Ethernet header is
at least 16 bytes.

It appears macvtap has only 14 bytes available on arches
where NET_IP_ALIGN is 0 (like x86)

Effect is a corruption of 2 bytes right before skb->head,
and possible crashes if accessing non existing memory.

This fix should also increase IPv4 performance, as paranoid code
in ip_finish_output2() wont have to call skb_realloc_headroom()
Reported-by: NBrian Rak <brak@vultr.com>
Tested-by: NBrian Rak <brak@vultr.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2f1d8b9e
    • G
      drivers: net: cpsw: Set SECURE for dual_emac ucast · 56887149
      由 George McCollister 提交于 
      Prior to this patch, sending a packet with the source MAC address of one
of the CPSW interfaces to one of the CPSW slave ports while it's configured in
dual_emac mode would update the port_num field of the VLAN/Unicast Address
Table Entry. This would cause it to discard all incoming traffic addressed to
that MAC address, essentially rendering the port useless until the ALE table is
cleared (by starting and stopping the interface or rebooting.)

For example, if eth0 has a MAC address of 90:59:af:8f:43:e9 it will have
an ALE table entry:

00 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=0 addr=90:59:af:8f:43:e9)

If you configure another device with the same MAC address and connect it
to the first CPSW slave port and send some traffic the ALE table entry
becomes:

04 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=1 addr=90:59:af:8f:43:e9)

>From this point forward all incoming traffic addressed to
90:59:af:8f:43:e9 will be dropped.

Setting the SECURE bit for the VLAN/Unicast address table entry for each
interface's MAC address corrects the problem.
Signed-off-by: NGeorge McCollister <george.mccollister@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      56887149
    • D
      niu: fix error handling in niu_class_to_ethflow() · f55ea3d9
      由 Dan Carpenter 提交于 
      There is a discrepancy here because the niu_class_to_ethflow() returns
zero on failure and one on success but the caller expected zero on
success and negative on failure.

The problem means that we allow the user to pass classes and flow_types
which we don't want.  I've looked at it a bit and I don't see it as a
very serious bug.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f55ea3d9
    • A
      net: smc91x: use run-time configuration on all ARM machines · b70661c7
      由 Arnd Bergmann 提交于 
      The smc91x driver traditionally gets configured at compile-time
for whichever hardware it runs on. This no longer works on
ARM as we continue to move to building all-in-one kernels.

Most ARM configurations with this driver already use run-time
configuration through DT or through platform_data, but a
few have not been converted yet.

I've checked all ARM boards that use this driver in their
legacy board files, and converted the ones that were using
compile-time configuration in smc91x.h to behave like the
other ones and provide the interrupt polarity along with
the MMIO configuration (width, stride) at platform device
creation time.

In particular, these combinations were previously selectable
in Kconfig but in fact broken:

- sa1100 assabet plus pleb
- msm combined with any other armv6/v7 platform
- pxa-idp combined with any non-DMA pxa variant
- LogicPD PXA270 combined with any other pxa
- nomadik combined with any other armv4/v5 platform,
  e.g. versatile.

None of these seem critical enough to warrant a backport
to stable, but it would be nice to clean this up for good.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
----
I would like the patch to get merged through netdev, after
Robert and/or Linus have verified it on at least some hardware.

There are a few other non-ARM platforms using this driver,
I could do the same patch for those if we want to take
it further.

 arch/arm/mach-msm/board-halibut.c    |   8 ++++-
 arch/arm/mach-msm/board-qsd8x50.c    |   8 ++++-
 arch/arm/mach-pxa/idp.c              |   5 +++
 arch/arm/mach-pxa/lpd270.c           |   8 ++++-
 arch/arm/mach-realview/core.c        |   7 ++++
 arch/arm/mach-realview/realview_eb.c |   2 +-
 arch/arm/mach-sa1100/neponset.c      |   6 ++++
 arch/arm/mach-sa1100/pleb.c          |   7 ++++
 drivers/net/ethernet/smsc/smc91x.c   |   9 +++--
 drivers/net/ethernet/smsc/smc91x.h   | 114 ++----------------------------------------------------------
 10 files changed, 57 insertions(+), 117 deletions(-)
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b70661c7
  11. 28 2月, 2015 6 次提交
  13. 26 2月, 2015 7 次提交