- 30 5月, 2009 10 次提交
-
-
由 Jiri Pirko 提交于
This patch converts unicast address list to standard list_head using previously introduced struct netdev_hw_addr. It also relaxes the locking. Original spinlock (still used for multicast addresses) is not needed and is no longer used for a protection of this list. All reading and writing takes place under rtnl (with no changes). I also removed a possibility to specify the length of the address while adding or deleting unicast address. It's always dev->addr_len. The convertion touched especially e1000 and ixgbe codes when the change is not so trivial. Signed-off-by: NJiri Pirko <jpirko@redhat.com> drivers/net/bnx2.c | 13 +-- drivers/net/e1000/e1000_main.c | 24 +++-- drivers/net/ixgbe/ixgbe_common.c | 14 ++-- drivers/net/ixgbe/ixgbe_common.h | 4 +- drivers/net/ixgbe/ixgbe_main.c | 6 +- drivers/net/ixgbe/ixgbe_type.h | 4 +- drivers/net/macvlan.c | 11 +- drivers/net/mv643xx_eth.c | 11 +- drivers/net/niu.c | 7 +- drivers/net/virtio_net.c | 7 +- drivers/s390/net/qeth_l2_main.c | 6 +- drivers/scsi/fcoe/fcoe.c | 16 ++-- include/linux/netdevice.h | 18 ++-- net/8021q/vlan.c | 4 +- net/8021q/vlan_dev.c | 10 +- net/core/dev.c | 195 +++++++++++++++++++++++++++----------- net/dsa/slave.c | 10 +- net/packet/af_packet.c | 4 +- 18 files changed, 227 insertions(+), 137 deletions(-) Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
Signed-off-by: NJiri Pirko <jpirko@redhat.com> Signed-off-by: NJay Vosburgh <fubar@us.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Divy Le Ray 提交于
Add support for the Aquantia AQ1002 10G-BaseT phy. Signed-off-by: NDivy Le Ray <divy@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Divy Le Ray 提交于
Add support for the AEL2020 phy. Add PCI IDs of the boards using this phy. Signed-off-by: NDivy Le Ray <divy@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Divy Le Ray 提交于
cxgb3 no longer advertizes LLTX. Signed-off-by: NDivy Le Ray <divy@chelsio.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Graf Yang 提交于
When we register the MII bus to the platfrom bus, the Distributed Switch Architecture can hook in transparently. Signed-off-by: NGraf Yang <graf.yang@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Hennerich 提交于
- Remove dead long delay - Use proper defines - Remove broken implementation of the TX DMA Data Alignment TXDWA feature Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NBryan Wu <cooloney@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sonic Zhang 提交于
Writes to the DMA descriptors may sit in the internal Blackfin data buffers and not actually be available when the DMA engine goes to fetch them. This does not typically happen, but when dealing with short/fast packets such as UDP and polling KGDB, this occurs much more frequently. Same goes for heavy loads as seen by netperf tests or large scp transfers. So force the buffers to drain with SSYNC otherwise we get random malformed packets. Signed-off-by: NSonic Zhang <sonic.zhang@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NBryan Wu <cooloney@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Hennerich 提交于
The IRQ used by the Blackfin EMAC is internal to the peripheral and cannot be used to generate any other interrupt, so there is no point in marking it as IRQF_SHARED. Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NBryan Wu <cooloney@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
No need to release skb->dst, its now done by core network. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 5月, 2009 11 次提交
-
-
由 Florian Fainelli 提交于
This patch makes the korina driver poll the media for link change. This is actually required on Mikrotik RB532 (not RB532A) for korina to operate properly. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NFlorian Fainelli <florian@openwrt.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 FUJITA Tomonori 提交于
This replaces dma_sync_single() with dma_sync_single_for_cpu() because dma_sync_single() is an obsolete API; include/linux/dma-mapping.h says: /* Backwards compat, remove in 2.7.x */ #define dma_sync_single dma_sync_single_for_cpu #define dma_sync_sg dma_sync_sg_for_cpu Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round) Now that core network takes care of trans_start updates, dont do it in drivers themselves, if possible. Drivers can avoid one cache miss (on dev->trans_start) in their start_xmit() handler. Exceptions are NETIF_F_LLTX drivers Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Followup of commits 9d21493b and 08baf561 (net: tx scalability works : trans_start) (net: txq_trans_update() helper) Now that core network takes care of trans_start updates, dont do it in drivers themselves, if possible. Multi queue drivers can avoid one cache miss (on dev->trans_start) in their start_xmit() handler. Exceptions are NETIF_F_LLTX drivers (vxge & tehuti) Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Inaky Perez-Gonzalez 提交于
When the i2400m is connected to a network, the host interface (USB) cannot be suspended. For that to happen, the device has to have negotiated with the basestation to put the link on IDLE state. If the host tries to put the device in standby while it is connected but not idle, the device resets, as the driver should not do that. To avoid triggering that, when the USB susbsytem requires the driver to autosuspend the device, the driver checks if the device is not yet idle. If it is not, the request is requested (will be retried again later on after the autosuspend timeout). At some point the device will enter idle and the request will succeed (unless of course, there is network traffic, but at that point, there is no idle neither in the link or the host interface). Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
-
由 Inaky Perez-Gonzalez 提交于
From a fix by Cindy H Kao: Block size has to be set before sending IOE enable because the firmware reads the block size register before it reads IOE register. Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
-
由 Inaky Perez-Gonzalez 提交于
Functions i2400m_report_tlv*() are only called from i2400m_report_hook(), called in a workqueue by i2400m_report_hook_work(). The scheduler checks for device readiness before scheduling. Added an extra check for readiness in i2400m_report_hook_work(), which makes all the checks down the line redundant. Obviously the device state could change in the middle, but error handling would take care of that. Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
-
由 Inaky Perez-Gonzalez 提交于
i2400m_report_state_hook() is going to get messier as we add handling code. Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
-
由 Inaky Perez-Gonzalez 提交于
By running 'echo 1 > /sys/kernel/debug/wimax:wmxX/i2400m/trace_msg_from_user', the driver will echo to user space all the commands being sent to the device from user space, along with the responses. However, this only helps with the commands being sent from user space; with this patch, the trace hook is moved to i2400m_msg_to_dev(), which is the single access point for running commands to the device (both by user space and the kernel driver). This allows better debugging by having a complete stream of commands/acks and reports. Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
-
由 Inaky Perez-Gonzalez 提交于
When commands are sent from user space, trace both the command sent and the answer received over the "echo" pipe instead of over the "trace" pipe when command tracing is enabled. As well, when the device sends a reports/indications, send it over the "echo" pipe. The "trace" pipe is used by the device to send firmware traces; gets confusing. Another named pipe makes it easier to split debug information. Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
-
由 Inaky Perez-Gonzalez 提交于
The WiMAX i2400m driver needs to generate a fake source MAC address to fake an ethernet header (for destination, the card's MAC is used). This is the source of the packet, which is the basestation it came from. The basestation's mac address is not usable for this, as it uses its own namespace and it is not always available. Currently the fake source MAC address was being set to all zeros, which was causing trouble with bridging. Use random_ether_addr() to generate a proper one that creates no trouble. Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
-
- 28 5月, 2009 6 次提交
-
-
由 David S. Miller 提交于
First of all, it exposes the SKB list implementation. Second of all it's not needed. If we get called here, we successfully enqueued the URB with the linked SKB and such a completion only gets called one time on such an SKB. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
This eliminates explicit references to the SKB list handling implementation. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Use struct net_device_stats provided in struct net_device instead of private ones. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
This patch removes the not-that-useful message in the r6040_timer which prints the PHY status. Instead replace it with a call to mii_check_media which will update the link status and print it on startup. Signed-off-by: NFlorian Fainelli <florian@openwrt.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 5月, 2009 13 次提交
-
-
由 Peter P Waskiewicz Jr 提交于
This patch fixes a build warning due to an unused label. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Use MII_BUS_ID_SIZE instead. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jean Delvare 提交于
The r8169 driver supports 3 different families of network chips (RTL8169, RTL8168 and RTL8101). When an unknown version is found, the driver currently always defaults to the RTL8169 variant. This has very little chance to ever work for chips of the other families. So better define a per-family default. Signed-off-by: NJean Delvare <jdelvare@suse.de> Acked-by: NFrancois Romieu <romieu@fr.zoreil.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Kevin Hao 提交于
Inspired by the patch for 8139too (bda6a15a). Currently we can't set mac address on a running ucc_geth device. But this is needed when you use this device as a bonding slave in bonding device in balance-alb mode. So add this feature for ucc_geth device. Signed-off-by: NKevin Hao <kexin.hao@windriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tanli Chang 提交于
This patch is for supporting C10NEM. C10NEM is a switch module, which has back-to-back XAUI link connected to blades. Signed-off-by: NTanli Chang <tanli.chang@sun.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Don Skidmore 提交于
If we loaded the driver with out a SFP module plugged in it would leave it in a state that make it later unable to link when a module was plugged in. This patch corrects that by: ixgbe_probe() - moving the check for IXGBE_ERR_SFP_NOT_PRESENT from after get_invariants() to after reset_hw() as now reset_hw() is where this condition will be indentified. ixgbe_reset_hw_82598() - Enable this function to now return IXGBE_ERR_SFP_NOT_PRESENT. ixgbe_identify_sfp_module_generic() - This where the lack of SFP module is detected. Modifications are added to allow a different return value for modules that just haven't been plugged in yet. Other functions were updated to allow correct logging. Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peter P Waskiewicz Jr 提交于
Device ID 0x10d8 is the default silicon device ID for 82599. However, the device will not be functional without an EEPROM, so we want to prevent the driver from loading on the device. Otherwise, the driver will load, but no PHY setup or PCIe setup will occur, causing the device to be unusable. To prevent users from encountering this, just remove the device ID. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
The phy port status register has the MDI-X status bit on bit 11, not bit 3 as is currently setup in the define. This patch corrects that so the correct bit is checked on igp PHY types. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Acked-by: NBruce Allan <bruce.w.allan@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jesper Dangaard Brouer 提交于
Based on previous patch from Jesper Dangaard Brouer. The RNBC (Receive No Buffers Count) register for the 82576, indicate that frames were received when there were no available buffers in host memory to store those frames (receive descriptor head and tail pointers were equal). The packet is still received by the NIC if there is space in the FIFO on the NIC. As the RNBC value is not a packet drop, the driver stores this value in net_stats.rx_fifo_errors to indicate that there were no system buffers available for the incoming packet. Actual dropped packets are counted in the MPC value. Saving the stats in dev->net_stats makes it visible via /proc/net/dev as "fifo", and thus viewable to ifconfig as "overruns" and 'netstat -i' as "RX-OVR". The Receive No Buffers Count (RNBC) can already be queried by ethtool -S as "rx_no_buffer_count". Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Jesper Dangaard Brouer <hawk@comx.dk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jesper Dangaard Brouer 提交于
Based on the previous patches from Jesper Dangaard Brouer <hawk@comx.dk> Implement reading the per queue drop stats register RQDPC (Receive Queue Drop Packet Count). It counts the number of packets dropped by a queue due to lack of descriptors available. Notice RQDPC (Receive Queue Drop Packet Count) stats only gets incremented, if the DROP_EN bit it set (in the SRRCTL register for that queue). If DROP_EN bit is NOT set, then the some what equivalent count is stored in RNBC (not per queue basis). The RQDPC register is only 12 bit, thus the precision might suffer due to overrun in-netween the watchdog polling interval. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Jesper Dangaard Brouer <hawk@comx.dk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jeff Kirsher 提交于
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-