This driver supports the SPI controller on the MPC83xx SoC devices from
Freescale.  Note, this driver supports only the simple shift register SPI
controller and not the descriptor based CPM or QUICCEngine SPI controller.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Because several developers asked me about referenced but missing
spi_add_master(), I think that this patch should be applied ...  it
corrects comments so they refer to spi_register_master() instead.
Signed-off-by: Ndmitry pervushin <dpervushin@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This fixes coverity bug id #1237.  After the while loop, it is possible for
i == ISDN_LMSNLEN.  If this happens the terminating '\0' is written after
the end of the array.
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The OSC set and query functions do not allocate enough space for return
values, and set the output buffer length to a false, too large value.  This
causes the acpi-ca code to assume that the output buffer is larger than it
actually is, and overwrite memory when copying acpi return buffers into
this caller provided buffer.  In some cases this can cause kernel oops if
the memory that is overwritten is a pointer.  This patch will change these
calls to use a dynamically allocated output buffer, thus allowing the
acpi-ca code to decide how much space is needed.
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: "Yu, Luming" <luming.yu@intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make a read of a HID device block until data is available.  Without it, the
read goes into a busy-wait loop until data is available.

Cc: Greg KH <greg@kroah.com>
Acked-by: NVojtech Pavlik <vojtech@suse.cz>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We should be able to write 'repair' to /sys/block/mdX/md/sync_action,
however due to and inverted test, that always given EINVAL.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It looks like the generic ide code now wants ide_init_hwif_ports() to set
the parent struct device into the ide_hw structure (new field ?).  Without
this, the mac ide code can cause the ide probing code to explode in flames
in sysfs registration due to what looks like a stale pointer in there
(happens when removing/re-inserting one of the hotswap media bays on some
laptops).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There has been a longstanding problem with the Matrox G450 and perhaps
other similar cards, with modes "above" 1280x1024-60 on ppc/ppc64 boxes
running Linux.  Higher resolutions and/or higher refresh rates resulted in
a very noticably "jittery" display, and sometimes no display, depending on
the physical monitor.  This patch fixes that problem on the systems I have
easy access to...

I've tested with SLES9SP3 (2.6.5+ kernel) and 2.6.16-rc6 custom kernels on
an IBM eServer p5 520 w/G450 (a.k.a GXT135P on IBM's ppc64 systems), and a
colleague of mine (Ian Romanick) tested it successfully on an Apple ppc32
box (w/GXT135P).  I also tested it on IA32 box I have with a GXT135P to
verify that it didn't obviously break anything.  In my testing, I covered
single-card, single and dual-head setups using both HD15 and DVI-D signals,
on both the IA32 and ppc64 boxes.  While everything appeared fine on both
boxes, I did encounter one problem: I can't get any signal on the DVI-D
output on the ppc64 box.  However, this is also the case without my patch.

I just noticed that screen-blanking only occurs on the primary display as
well.
Signed-off-by: NPaul A. Clarke <pc@us.ibm.com>
Signed-off-by: NIan Romanick <idr@us.ibm.com>
Signed-off-by: NPetr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

With Manfred Spraul <manfred@colorfullife.com> and
     Andrew Morton <akpm@osdl.org>

Bring back this recently-reverted patch, only fixed.

Original changelog:

    From: Ayaz Abdulla <aabdulla@nvidia.com>

    This patch fixes the issues with multiple irqs.

    I am resending based on feedback. I decoupled the dma mask for
    consistent memory and fixed leak with multiple irq in error path.

    Thanks to Manfred for catching the spin lock problem.

Fix it:

    From: Manfred Spraul <manfred@colorfullife.com>

    Fix bug introduced by ebf34c9b, covered in
    http://bugzilla.kernel.org/show_bug.cgi?id=6568.

    Remove second instance of the request_irq() calls: they were moved
    from nv_open into nv_request_irq.

    Thanks to Alistair Strachan <alistair@devzero.co.uk> for reporting and
    persisting.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NManfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix all current kernel-doc warnings.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Increment the version number inside sata_mv.c.
Signed-off-by: NMark Lord <liml@rtr.ca>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This fixes a byte-swap issue on PPC, found by Zang Roy-r61911
on the powerpc platform.  His original patch also had some other
platform-specific changes in #ifdef's, but I'm not sure yet how to
incorporate them.  Look for another patch for those (soon).
Signed-off-by: NMark Lord <liml@rtr.ca>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver currently keeps local copies of the hardware request/response queue indexes.
But it expends significant effort ensuring consistency between the two views,
and still gets it wrong after an error or reset occurs.

This patch removes the local copies, in favour of just accessing the hardware
whenever we need them.  Eventually this may need to be tweaked again for NCQ,
but for now this works and solves problems some users were seeing.
Signed-off-by: NMark Lord <liml@rtr.ca>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The 60xx chips, and possibly others, incorrectly assert DEV_IRQ interrupts
on a regular basis.  The cause of this is under investigation (by me and
in theory by Marvell also), but regardless we do need to deal with these events.

This patch tidies up some interrupt handler code, and ensures that we ignore
DEV_IRQ interrupts when the drive still  has ATA_BUSY asserted.
Signed-off-by: NMark Lord <liml@rtr.ca>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The interface control register of the 60xx (and later) Marvell chip
requires certain bits to always be set when writing to it.  These bits
incorrectly read-back as zeros, so the pattern must be ORed in
with each write of the register.  Also, bit 12 should NOT be set
(note that Marvell's own driver also had bit-12 wrong here).

While we're at it, we also now do pci_set_master() in the init code.
Signed-off-by: NMark Lord <liml@rtr.ca>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

In some systems, it is possible that the BIOS may have enabled interrupt coalescing
for the Marvell controllers which support it.  This patch adds code to detect/ack
interrupts from the chip's coalescing (combing) logic.
Signed-off-by: NMark Lord <liml@rtr.ca>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The mv_err_intr() function is invoked from the driver's interrupt handler,
as well as from the timeout function.  This patch prevents it from triggering
a one-after-the-other double reset of the controller when invoked
from the timeout function.

This also adds a check for a timeout race condition that has been observed
to occur with this driver in earlier kernels.  This should not be needed,
in theory, but in practice it has caught bugs.  Maybe nuke it at a later date.
Signed-off-by: NMark Lord <liml@rtr.ca>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Call pci_map_single() with the actual size of the receive
buffers, not 0 (which skb->len is initialized to by dev_alloc_skb()).
Signed-off-by: NErling A. Jacobsen <linuxcub@email.dk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Dear Jeff

axnet_cs: bug fix multicast code (support older ax88190 chipset)

Signed-off-by: komurojun-mbn@nifty.com

Best Regards
Komuro
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver will get stuck (permanent transmit timeout), if the transmit
ring size is set too small.  It needs to have enough ring elements to
hold one maximum size transmit.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Skge driver always causes  bad checksums on big-endian.
The checksum in the receive control block was being swapped
when it doesn't need to be.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Need to track impact of this group of changes.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If the status ring processing can't keep up with the incoming frames,
it is more efficient to have NAPI keep scheduling the poll routine
rather than causing another interrupt.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Logic error in the phy initialization code. Also, turn on wake on lan
bit in status control.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Dlink DGE-560T uses Yukon2 chipset so it needs sky2 driver; and
the DGE-530T uses Yukon1 so it uses skge driver.

Bug: http://bugzilla.kernel.org/show_bug.cgi?id=6544Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If both ports are receiving on the SysKonnect dual port cards,
then it appears the bus interface unit can give an interrupt status
for frame before DMA has completed.  This leads to bogus frames
and general confusion. This is why receive checksumming is also
messed up on dual port cards.

A workaround for the out of order receive problem is to eliminating
split transactions on PCI-X.

This version is based of the current linux-2.6.git including earlier
patch to disable dual ports.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Revert previous patch with subject "change mdelay to msleep and remove
from ISR path".  This patch seems to have caused bigger problems than
it solved, and it didn't solve much of a problem to begin with...

Discussion about backing-out this patch can be found here:

	http://marc.theaimsgroup.com/?l=linux-netdev&m=114321570402396&w=2

The git commit associated w/ the original patch is:

	6ba98d31

Signed-off-by: John W. Linville <linville@tuxdriver.com
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Revert ebf34c9b.  Maybe.  Due to crashes
at shutdown - see http://bugzilla.kernel.org/show_bug.cgi?id=6568.

Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Patch from Pavel Pisa

There has been problems that for some paths that clock are not stopped
during new command programming and initiation. Result is issuing
of incorrect command to the card. Some other problems are cleaned too.
Noisy report of known ERRATUM #4 has been suppressed.
Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If we post a list of length 256 exactly, nreq in doorbell gets set to
256 which is wrong: it should be encoded by 0.  This is because we
only zero it out on the next WR, which may not be there.  The solution
is to ring the doorbell after posting a WQE, not before posting the
next one.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In ib_umem_release_on_close(), if the kmalloc() fails, then a
reference to current->mm will be leaked.  Fix this by adding a mmput()
instead of just returning on kmalloc() failure.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Re-enable posted writes for status FIFO.

Besides bringing back a very minor bandwidth tweak from Linux 2.6.15.x
and older, this also fixes an interoperability regression since 2.6.16:

   http://bugzilla.kernel.org/show_bug.cgi?id=6356
   (sbp2: scsi_add_device failed. IEEE1394 HD is not working anymore.)
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: NVanei Heidemann <linux@javanei.com.br>
Tested-by: Martin Putzlocher <mputzi@gmx.de> (chip type unconfirmed)
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In case the blacklist with workarounds for device bugs yields a false
positive, the module load parameter can now also be used as an override
instead of an addition to the blacklist.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Apple decided to copy some USB stupidity over to FireWire.

The sector number returned by iPods from read_capacity is one too many.
This may cause I/O errors, especially if the kernel is configured for EFI
partition support. We use the same workaround as usb-storage but have to
check for different model IDs.

	http://marc.theaimsgroup.com/?t=114233262300001
	https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=187409

Acknowledgements:
  Diagnosis and therapy by Mathieu Chouquet-Stringer <ml2news@free.fr>,
  additional data about affected and unaffected Apple hardware from
  Vladimir Kotal, Sander De Graaf, Bryan Olmstead and Hugh Dixon.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Grand unification of the three types of workarounds we have so far.

The "skip mode page 8" workaround is now limited to devices which
pretend to be of TYPE_DISK instead of TYPE_RBC. This workaround is no
longer enabled for Initio bridges.

Patch update in anticipation of more workarounds:
 - Add module parameter "workarounds".
 - Deprecate parameter "force_inquiry_hack".
 - Compose the blacklist of a compound type for better readability and
   extensibility.
 - Remove a now unused #define.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I still need this hack to work around the fact that softmac doesn't
attempt to associate when we bring the device up...
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When flushing out queued commands after a successful device reset,
make sure that SRP completes the right commands, instead of calling
scsi_done on the command passed into the device reset handler over and
over.
Signed-off-by: NIshai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If a reconnection attempt fails, then SRP does two scsi_host_put()s.
This is a historical relic from an earlier version of the driver that
took a reference on the scsi_host before trying to reconnect, so get
rid of the extra scsi_host_put().
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Sending a DREQ may fail, for example because the remote target has
already broken the connection.  If so, then SRP should not wait for
the disconnection to complete, because it never will.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Setting fw_cmd_doorbell allows FW command to be queued using posted
writes instead of requiring polling on a "go" bit, so it should be a
performance boost.  However, the option causes problems with at least
some device/firmware combinations, so set the default to 0 until we
understand what's going on better.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>