Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
接近 2 年 前同步成功

通知 170
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 03 5月, 2016 4 次提交
  3. 08 4月, 2016 5 次提交
    • Y
      gpio: pca953x: Use correct u16 value for register word write · 9b8e3ec3
      由 Yong Li 提交于 
      The current implementation only uses the first byte in val,
the second byte is always 0. Change it to use cpu_to_le16
to write the two bytes into the register

Cc: stable@vger.kernel.org
Signed-off-by: NYong Li <sdliyong@gmail.com>
Reviewed-by: NPhil Reid <preid@electromag.com.au>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      9b8e3ec3
    • G
      gpiolib: Defer gpio device setup until after gpiolib initialization · 159f3cd9
      由 Guenter Roeck 提交于 
      Since commit ff2b1359 ("gpio: make the gpiochip a real device"),
attempts to add a gpio chip prior to gpiolib initialization cause
the system to crash. This happens because gpio_bus_type has not been
registered yet. Defer creating gpio devices until after gpiolib has
been initialized to fix the problem.

Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Fixes: ff2b1359 ("gpio: make the gpiochip a real device")
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      159f3cd9
    • G
      gpiolib: Do not use devm functions when registering gpio chip · 476e2fc5
      由 Guenter Roeck 提交于 
      It is possible that a gpio chip is registered before the gpiolib
initialization code has run. This means we can not use devm_ functions
to allocate memory at that time. Do it the old fashioned way.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      476e2fc5
    • R
      gpio: pxa: fix legacy non pinctrl aware builds · c4e5ffb6
      由 Robert Jarzmik 提交于 
      In legacy pxa builds, ie. non device-tree and platform-data only builds,
pinctrl is not yet available. As a consequence, the pinctrl gpio
direction change function is a stub, returning always success.

In the current state, the gpio driver direction function believes the
pinctrl direction change was successful, and exits without actually
changing the gpio direction.

This patch changes the logic :
 - if the pinctrl direction function fails, gpio direction will report
   that failure
 - if the pinctrl direction function succeeds, gpio direction is changed
   by the gpio driver anyway.
   This is sub optimal in the pinctrl aware case, as the gpio direction
   will be changed twice: once by pinctrl function and another time by
   the gpio direction function.

Yet it should be acceptable in this form, as this is functional for all
pxa platforms (device-tree and platform-data), and moreover changing a
gpio direction is very very seldom, usually in machine initialization,
seldom in drivers probe, and an exception for ac97 reset bug.

Fixes: a770d946 ("gpio: pxa: add pin control gpio direction and request")
Reported-by: NGuenter Roeck <guenter@roeck-us.net>
Tested-by: NGuenter Roeck <guenter@roeck-us.net>
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      c4e5ffb6
    • D
      gpio / ACPI: ignore GpioInt() GPIOs when requesting GPIO_OUT_* · 25487533
      由 Dmitry Torokhov 提交于 
      When firmware does not use _DSD properties that allow properly name GPIO
resources, the kernel falls back on parsing _CRS resources, and will
return entries described as GpioInt() as general purpose GPIOs even
though they are meant to be used simply as interrupt sources for the
device:

Device (ETSA)
{
	Name (_HID, "ELAN0001")
	...

	Method(_CRS, 0x0, NotSerialized)
	{
		Name(BUF0,ResourceTemplate ()
		{
			I2CSerialBus(
				0x10,                     /* SlaveAddress */
				ControllerInitiated,      /* SlaveMode */
				400000,                   /* ConnectionSpeed */
				AddressingMode7Bit,       /* AddressingMode */
				"\\_SB.I2C1",             /* ResourceSource */
			)
			GpioInt (Edge, ActiveLow, ExclusiveAndWake, PullNone,,
				 "\\_SB.GPSW") { BOARD_TOUCH_GPIO_INDEX }
		} )
		Return (BUF0)
	}
...
}

This gives troubles with drivers such as Elan Touchscreen driver
(elants_i2c) that uses devm_gpiod_get to look up "reset" GPIO line and
decide whether the driver is responsible for powering up and resetting
the device, or firmware is. In the above case the lookup succeeds, we
map GPIO as output and later fail to request client->irq interrupt that
is mapped to the same GPIO.

Let's ignore resources described as GpioInt() while parsing _CRS when
requesting output GPIOs (but allow them when requesting GPIOD_ASIS or
GPIOD_IN as some drivers, such as i2c-hid, do request GPIO as input and
then map it to interrupt with gpiod_to_irq).
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NDmitry Torokhov <dtor@chromium.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      25487533
  5. 30 3月, 2016 2 次提交
  7. 16 3月, 2016 5 次提交
  9. 09 3月, 2016 9 次提交
  11. 08 3月, 2016 2 次提交
    • A
      gpio: timberdale: Switch to devm_ioremap_resource() · fa283db7
      由 Amitoj Kaur Chawla 提交于 
      Replace calls to devm_request_mem_region and devm_ioremap with a
direct call to devm_ioremap_resource instead and modify error
handling.

Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more
clear.

A simplified version of the Coccinelle semantic patch that is used to
make this change is as follows:
//<smpl>
@nm@
expression myname;
identifier i;
@@

struct platform_driver i = { .driver = { .name = myname } };

@@
expression dev,res,size,e1,e;
expression nm.myname;
@@

-if (!devm_request_mem_region(dev, res->start, size,
-                              \(res->name\|dev_name(dev)\|myname\)))
                               {
-   ...
-   return ...;
-}
... when != res->start = e1
e =
-devm_ioremap(dev,res->start,size);
+devm_ioremap_resource(dev,res);

if
-(e == NULL)
+(IS_ERR(e))
{
 ...
-return ...;
+return PTR_ERR(e);
}
//</smpl>

Further, updated error handling by hand as devm_ioremap_resource
gives appropriate error messages, so remove unnecessary error
messages.
Signed-off-by: NAmitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      fa283db7
    • J
      gpio: ts4800: Add IMX51 dependency · 6dcfd729
      由 Julien Grossholtz 提交于 
      The TS-4800 is an i.MX515 board. Its GPIO driver should only be compiled
for this CPU or for test builds.
Signed-off-by: NJulien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      6dcfd729
  13. 07 3月, 2016 3 次提交
  15. 26 2月, 2016 1 次提交
  17. 25 2月, 2016 9 次提交