Some boards need to set the INn_MODE[1:0] register to change
the input signal patch. This wlf,inmode property is optional.
If present, values must be specified less than or equal to
the number of input singals. If values less than the number
of input signals, elements that has not been specifed are set
to 0 by default.

Example:
   - wlf,inmode = <2 0 2>;	/* IN1, IN3 use DMIC */
Signed-off-by: NInha Song <ideal.song@samsung.com>
Reviewed-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Some arizona devices have a second asynchronous sample rate, add the
registers necessary to support this.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Ricoh RN5T618 is a power management IC which integrates 3 step-down
DCDC converters, 7 low-dropout regulators, a Li-ion battery charger,
fuel gauge, ADC, GPIOs and a watchdog timer.

This commit adds a MFD core driver to support the I2C communication
with the device.
Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

After enabling and disabling ADC continuous mode via sysfs, ts_print_raw
fails to return any data. This is because when ADC is configured for
continuous mode, it disables touch screen steps.These steps are not
re-enabled when ADC continuous mode is disabled. Therefore existing values
of REG_SE needs to be cached before enabling continuous mode and
disabling touch screen steps and enabling ADC steps. The cached value
are to be restored to REG_SE once ADC is disabled.

Fixes: 7ca6740c ("mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization")

Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: NVignesh R <vigneshr@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This adds the device tree bindings documentation for Ricoh RN5T618.
Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com>
Reviewed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The include guard doesn't work as intended due to the transposition
typo DAVINCI -> DAVINIC.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

http://www.ti.com/lit/pdf/SWCZ010:
  Glitch on SDA-SCL not managed correctly by the I2C IP

Impact:
The standard specifies that the I2C transfer should restart on a start
event in all cases. The current design does not support two consecutive
Start conditions. This can cause the first real access after such a
glitch to be corrupted.

Description:
An unexpected glitch on SDA and SCL can generate a wrong start event.
In the current design, the SCL line must toggle two times to detect a
new start event and completely restart the I2C access; hence the real
start event is not detected in the case of a single SCL toggle.

Workaround:
Repeat I2C access.

A simpler workaround is to make a dummy transfer just before the first
access to the tps65910 chip. This can be done unconditionally.
Signed-off-by: NArnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Acked-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The header file include/linux/mfd/ti_ssp.h does not seem to be used
anywhere. It was orphaned by 3033ee62 "mfd: Remove obsolete ti-ssp
driver". Remove it.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Numbers are generated by taking the largest currently used values.

drivers/mfd/stmpe.c:252:17:
  warning: Variable length array is used.
drivers/mfd/stmpe.c:857:16:
  warning: Variable length array is used.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The largest byte size in use currently is 8.  Fix array size to 9.

drivers/mfd/max8925-i2c.c:40:33:
  warning: Variable length array is used
Signed-off-by: NLee Jones <lee.jones@linaro.org>

drivers/mfd/88pm860x-i2c.c:125:33:
  warning: Variable length array is used.
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The following functions appear to be unused since v2.6.39:

  pm860x_page_reg_read()
  pm860x_page_bulk_write()
  pm860x_page_set_bits()

Let's remove them.
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds the LPC Device IDs for the Intel 9 Series PCH.
Signed-off-by: NJames Ralston <james.d.ralston@intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch improves support for the flash cell of
max77693 mfd by adding relevant of_compatible field
and a structure for caching related platform data.
Added are also FLASH registers related macro definitions.
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

According to the MAX77693 documentation the name of
the register is FLASH_STATUS.
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This is the same as used in Baytrail so add the new PCI ID to the driver's
list of supported IDs.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Since commit b4226107 ("regmap: i2c: fallback to SMBus if the adapter
does not support standard I2C"), regmap-i2c will check the
I2C_FUNC_SMBUS_[BYTE|WORD]_DATA functionality based on the regmap_config
setting if the adapter does not support standard I2C.

So remove the I2C_FUNC_SMBUS_BYTE_DATA functionality check in the driver code.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Convert a zero return value on error to a negative one, as returned
elsewhere in the function.

Additionally, converted 1 << 7 to BIT(7) at the suggestion of Lee Jones.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

regmap_add_irq_chip is called from arizona_irq_init with the irq_base
specified as -1 and regmap_add_irq_chip uses if (irq_base) to check if
it should use legacy IRQ mapping. As such the irq mappings are currently
added with irq_domain_add_legacy, rather than irq_domain_add_linear.
This is clearly a typo as there is no reason why this driver can't use
irq_domain_add_linear.

This patch corrects this by passing the irq_base as zero to
regmap_add_irq_chip.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Mark some additional registers as volatile. The write sequencer control
registers should not be cached, as we don't ever want their value
synchronised as this might cause a write sequence to be accidentally
initiated.

Additionally, the DAC_COMP registers require special preconditions to
write so there values wouldn't be updated accurately during a register
sync.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

During init the core checks if the wm5102 has finished starting by reading
register 0x19 and looking at the value. This read always fails since this
is not a readable register, mark it as being one. While we're at it provide
a constant for the register name (as supplied by Charles Keepax).
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.

Found by using regex suggested by Joe Perches.
Signed-off-by: NHans Wennborg <hans@hanshq.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Convert a zero return value on error to a negative one, as returned
elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The interfaces that used to be built in only (interrupts IIRC) no longer
are so allow the driver to be built as a module fixing arm64 allmodconfig
builds.
Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

If vtg is NULL, it is not possible to access its mode_reg field. At all
sites where the static function menelaus_set_voltage is called, the first
argument is the address of a structure defined in the file. So, the null
test is unnecessary and is removed. Also, a label is done away with.

This problem was found using the following Coccinelle semantic match:

// <smpl>
@@
expression E, E1;
identifier f;
statement S1,S2,S3;
@@

* if (E == NULL)
{
  ... when != if (E == NULL) S1 else S2
      when != E = E1
* E->f
  ... when any
  return ...;
}
else S3
// </smpl>
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

We'd like to be able to build the WM8994 family as modules, but the
build will fail if the external symbols aren't exported first.
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Suspicious implicit sign extension where 'reg' (unsigned char) is
promoted in reg << clksrc to int, then sign-extended to unsigned
long. If reg << clksrc is greater than 0x7FFFFFFF, the upper bits
of the result will all be 1.
Signed-off-by: NLee Jones <lee.jones@linaro.org>

In the original code a return value variable was provided, but it
was never checked and the user was never informed of failure.  Now
it is and they are.
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The return value of platform_device_add() is checked after every
other use throughout the kernel.

We're also sliding in another cheeky dev_err() => dev_warn() change
as we're not actually erroring out here, rather reporting the fact
that something's gone wrong, but carrying on regardless.
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As 'reg' is unsigned, it can't be less than 0, so checking if it is
greater than or equal to 0 will always result in a true condition.
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Chip identifier wm5102_reva_patch is always overwritten with
wm5102_revb_patch, even when the code is run on a Rev-A chip.  Place
in the missing break to force the code into doing something sensible
instead.
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Checking the result of container_of() against NULL will always result to
false.  Using the offset of member 'chip_out' to find the start of 'struct
htcpld_chip' will result in an offset error when .get_chip() is attempting
to obtain 'htcpld-in'.  Instead, we'll use the correct member based on a
previously the set chip label.
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This aids in consistency, as the rest of the checks in the file use this
notation.
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Logically dead code (DEADCODE)

dead_error_line: Execution cannot reach this statement: return;

Remove the check for NULL.
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Calling strncpy with a maximum size argument of 32 bytes on destination
array kim_gdata->dev_name of size 32 bytes might leave the destination
string unterminated.

Cc: gregkh@linuxfoundation.org
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Coverity reported:
  This less-than-zero comparison of an unsigned value is never true.

In answer to that, we only ever decrement if protos_registered is
positive.  We can subsequently remove the paranoid checking during
unregister.

Cc: gregkh@linuxfoundation.org
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Value from st_sensors_set_drdy_int_pin() is assigned to err here,
but that stored value is not used before it is overwritten.  To fix
this we're enforcing a check on st_sensors_set_drdy_int_pin()'s
return value and if it's an error, we're returning right away.

Cc: jic23@kernel.org
Cc: linux-iio@vger.kernel.org
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Merge branches 'ib-mfd-arm-3.18', 'ib-mfd-hwmon-leds-watchdog-3.18' and 'ib-mfd-power-charger-regulator-3.18' into ibs-for-mfd-merged

Added driver to support the 14F021P00 BMC Hardware Monitoring.
The BMC is a Board Management Controller including monitoring of the
board voltages.
Signed-off-by: NAndreas Werner <andreas.werner@men.de>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Added driver to support the 14F021P00 BMC LEDs.
The BMC is a Board Management Controller including four LEDs which
can be switched on and off.
Signed-off-by: NAndreas Werner <andreas.werner@men.de>
Acked-by: NBryan Wu <cooloney@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>