When using only subdev user-space operations the camera
interface input was not configured properly. Fix this by
updating the corresponding data structure in set_fmt
operation.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With 16-bit RGB565 colour format pixels are stored by the device in memory
in the following order:

    | b3  | b2  | b1  | b0  |
   ~+-----+-----+-----+-----+
    | R5 G6 B5  | R5 G6 B5  |

This corresponds to V4L2_PIX_FMT_RGB565 fourcc, not V4L2_PIX_FMT_RGB565X.
This change is required to avoid trouble when setting up video pipeline
with the s5p-tv devices, so the colour formats at both devices can be
properly matched.

Cc: <stable@kernel.org>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When a sensor with MIPI-CSI interface is attached through platform
data definition and the MIPI-CSI receiver is not selected in kernel
configuration s5p-fimc driver probe() will now succeed, issuing only
a warning. It was done this way to allow the driver to work even if
system configuration is not exactly right.

Instead make the driver's probe() fail if a MIPI-CSI sensor was
requested but s5p-csis module is not present.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Minimum vertical pixel size alignment for input and output DMA and
the scaler depend on color format, rotation, the IP instance and revision.

Make vertical pixel size of format and crop better fit for each SoC
revision and the IP instance by adding min_vsize_align attribute to
the FIMC variant data structure. It's now common for the DMA engines
and the scaler.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The "s5p-fimc-md" platform device platform_data is used to pass
attached camera sensor data. Not allowing device probe() to succeed
when it's null prevents using FIMC as a mem-to-mem device only.
Fix this by removing the platform_data check against null and
registering sensors only if platform_data is specified.
Also add logging of the information which /dev/video is assigned
to which device during probe().
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When requested more than 2 buffers the buffer dequeue order was wrong
due to erroneous updating FIMC registers in every interrupt handler
call. This also fixes regression of resetting the output DMA buffer
pointer at wrong time, when some buffers are already queued in hardware.
The hardware is reset in the start_streaming callback in order to align
the H/W state with the software output buffer pointer (buf_index).

Additionally a simple write to S5P_CISCCTRL register is replaced with
a read/modification/write to make sure the scaler is not being disabled
in fimc_hw_set_scaler().
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

ST_LPM bit must not be initially set, so the first resume helper
call properly quiesce the device's operation.
Also fimc_runtime_suspend() at device remove is unneeded and
leads to unbalanced clock disable so remove it.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make sure the subdev pointer is cleared when the subdev object
has been freed.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

After i2c_unregister_device() has been called the client object can already
be freed and thus using the client pointer may lead to dereferencing freed
memory. Avoid this by saving the adapter pointer for further use before
i2c_unregister_device() call.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In preparation for the forthcoming VIDIOC_CREATE_BUFS ioctl add a
"const struct v4l2_format *" argument to the .queue_setup() vb2
operation.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Switch to generic media bus signal polarity flags and allow
configuring the FIELD signal polarity.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The driver supports only multi-planar API and conversion to single-planar
API should be done in libv4l2. Remove misleading single planar capability
flags to avoid problems in applications and libv4l2.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Horizontal crop offset must be multiple of 2 otherwise
color distortion occurs.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for whole pipeline suspend/resume. Sensors must support
suspend/resume through s_power subdev operation.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Also correct and improve *_queue_add/pop functions description.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for transparent DMA transfer of JPEG data with MIPI-CSI2
USER1 format. In JPEG mode the color effect, scaling and cropping
is not supported as well as image rotation and flipping thus these
controls are marked as inactive if V4L2_PIX_FMT_JPEG pixel format
was selected.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a subdev to expose the host's scaling and composition functions.
The camera frame composition onto an output buffer may be configured
through set/get_crop at FIMC.{n} source pad.
Additionally allow crop, composition and controls to be modified
during streaming. Make sure the default format is set when opening
the video capture node.
Rename struct fimc_vid_cap::fmt to more relevant 'mf' to avoid
confusion.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In the camera capture driver use fimc_pipeline_* calls provided by
the media device driver part, in place where v4l2_subdev_call() were
used. This way the capture driver don't need to differentiate between
various H/W pipeline setups, i.e. if the MIPI-CSI receiver subdev is
used or not.

Remove the sync_capture_fmt() function instead of which
fimc_pipeline_try_format() is introduced in the following patch adding
the FIMC capture subdev.

The TRY_FMT ioctl function is completed by a subsequent patch adding
the capture subdev, so the try_fmt routines can be reused in the subdev
and the video node ioctl handlers.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Replace fimc_find_format() and find_mbus_format() with single function
that can return a pointer to the private format description based
on fourcc, media bus code or index in the table.

Create separate VIDIOC_ENUM_FMT ioctl handlers for video capture
and mem-to-mem video node. This is needed because some formats are
valid only for the video capture and some only for the mem-to-mem
video node.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Move the camera capture H/W initialization sequence to a separate
function. This is needed for reuse in the following runtime PM code.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add the link_setup handler for the camera capture video node.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert the v4l controls code to use the new control framework.

fimc_ctrls_activate/deactivate functions are introduced for the
transparent DMA transfer mode (JPEG), where the rotation and flipping
controls are not supported.

The capture video node does not inherit sensors' controls when the
subdevs are configured by the user space (user_subdev_api == true).
However by default after the driver's initialization
the 'user-subdev_api' flag is false and any sensor controls will
also be available at the video node.

When the pipeline links are disconnected through the media device
the FIMC and any sensor inherited controls are destroyed and then
again created when the pipeline connection completes.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is a prerequisite for the patch converting the driver to use
the control framework. As the capture driver does not use per file
handle contexts, two separate ioctl handlers are created for it
(vidioc_try_fmt_mplane, and vidioc_g_fmt_mplane) so there is no
handlers shared between the memory-to-memory and capture video node.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a top level media device driver aggregating FIMC video devnodes,
MIPI-CSIS and sensor subdevs. This driver gathers all media entities
and creates the possible links between them during initialization. By
default some links will be activated to enable access to all available
sensors in the system. For example if there are sensors S0, S1 listed
in the media device platform data definition they will be by default
assigned to FIMC0, FIMC1 respectively, which in turn will corresponds
to separate /dev/video?.
There is enough FIMC H/W entities to cover all available physical camera
interfaces in the system.

The fimc media device driver is bound to the "s5p-fimc-md" platform device.
Such platform device should be created by board initialization code
and camera sensors description array need to be specified as its
platform data.

The media device driver also implements various video pipeline operations,
for enabling subdevs power, streaming, etc., which will be used by the
capture video node driver.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Currently there is a v4l2_device instance being registered per each
(capture and memory-to-memory) video node created per FIMC H/W instance.
This patch is a prerequisite for using the top level v4l2_device
instantiated by the media device driver.
To retain current debug trace semantic (so it's possible to distinguish
between the capture and m2m FIMC) the video_device is used in place
of v4l2_device where appropriate.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The sensor subdevs need to be shared between all available FIMC instances.
Remove their registration from FIMC capture driver so they can then be
registered to the media device driver.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The current driver allowed camera sensors to be used only with single
FIMC H/W instance, FIMC0..FIMC2/3, designated at compile time. Remaining FIMC
entities could be used for video processing only, as mem-to-mem devices.
Required camera could be selected with S_INPUT ioctl at one devnode only.

However in that case it was not possible to use both cameras independently
at the same time, as all sensors were registered to single FIMC capture
driver. In most recent S5P SoC version there is enough FIMC H/W instances
to cover all physical camera interfaces.
Each FIMC instance exports its own video devnode. Thus we distribute
the camera sensors one per each /dev/video? by default. It will allow to
use both camera simultaneously by opening different video node.

The camera sensors at FIMC are now not selected with S_INPUT ioctl, there
is one input only available per /dev/video?.

By default a single sensor is connected at FIMC input as specified by the
media device platform data subdev description table. This assignment
can be changed at runtime through the pipeline reconfiguration at the media
device level.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are 2 separate clock outputs available in the SoC for external sensors.
These two clocks can be shared among all FIMC entities and there is
currently no any arbitration of the clocks in the driver.

So make the capture driver not touching these clocks and let them be
be properly handled at the media device driver level, enabling proper
arbitration between FIMC entities.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Do not register video nodes during FIMC device probe. Also make
fimc_register_m2m_device() public for use by the media device driver.
The video nodes are to be registered during the media device driver
initialization, altogether with the subdev devnodes. The video
capture nodes need to be registered as last ones when the remaining
pipeline elements are already initialized.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add intialization of the media entities for video capture
and mem-to-mem video nodes. The mem-to-mem entity has no pads
whereas the capture entity has single sink pad.
Also clean up the video node naming for consistency.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Do not resume the device during system resume if it was idle
before system suspend, as this causes resume from suspend
to RAM failures on Exynos4. For this purpose runtime PM and
system sleep helpers are separated.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On the SoCs this driver is intended to support the are three separate
pins to supply the MIPI-CSIS subsystem: 1.1V or 1.2V, 1.8V and power
supply for an internal PLL.
This patch adds support for two separate voltage supplies to cover
properly board configurations where PMIC requires to configure
independently each external supply of the MIPI-CSI device. The 1.8V
and PLL supply are assigned a single "vdd18" regulator supply name
as it seems more reasonable than creating separate regulator supplies
for them.

While at here stop using the 'fixed_phy_vdd' platform_data field.
It has been introduced for boards where the MIPI-CSIS supplies are
not controllable. However it is not needed as those boards can use
the dummy regulator.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add runtime PM and system sleep support in the memory-to-memory
driver. It's required to enable the FIMC operation on Exynos4
SoCs. This patch prevents system boot failure when the driver
is compiled in, as it now tries to access its I/O memory without
first enabling the corresponding power domain.

The camera capture device suspend/resume is not fully covered,
the capture device is just powered on/off during the video
node open/close. However this enables it's normal operation
on Exynos4 SoCs.

[mchehab@redhat.com: fix a small checkpatch error]
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch changes the order of operations during stream on call. Now the
buffers are first queued to the driver and then the start_streaming method
is called.

This resolves the most common case when the driver needs to know buffer
addresses to enable dma engine and start streaming. Additional parameter
to start_streaming method have been added to simplify drivers code. The
driver are now obliged to check if the number of queued buffers is high
enough to enable hardware streaming. If not - it can return an error. In
such case all the buffers that have been pre-queued are invalidated.

This patch also updates all videobuf2 clients to work properly with the
changed order of operations.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
CC: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
CC: Hans Verkuil <hverkuil@xs4all.nl>
CC: Tomasz Stanislawski <t.stanislaws@samsung.com>
CC: Sylwester Nawrocki <s.nawrocki@samsung.com>
CC: Kamil Debski <k.debski@samsung.com>
CC: Jonathan Corbet <corbet@lwn.net>
CC: Josh Wu <josh.wu@atmel.com>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Paul Mundt <lethal@linux-sh.org>
Tested-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the correct 'dma_addr' name for the buffer address. 'paddr' suggested
that this is the physical address in system memory. For most ARM platforms
these two are the same, but this is not a generic rule. 'dma_addr' will
also point better to dma-mapping api.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Plane sizes array was declared as unsigned long[], while unsigned int is
more than enough for storing size of the video buffer. This patch reduces
the size of the array by definiting it as unsigned int[].
Reported-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Standardize the remaining video drivers to return the API version
for the VIDIOC_QUERYCAP version, instead of a per-driver version.

Those drivers had the version updated more recently or are SoC
drivers. Even so, it doesn't sound a good idea to keep a per-driver
version control, so, let's use the per-subsystem version control
instead.
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With multi-planar formats fmt.pix_mp member of struct v4l2_format
should be used rather than fmt.pix. Fix find_fmt() function to do
the right thing.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>