Use smp_send_stop() to move all cpus besides the one executing reboot
into a hold loop, to keep them from being in powersavings mode at the
time of reboot.
Signed-off-by: NOlof Johansson <olof@lixom.net>

There will be more product numbers in the future than just PA6T-1682M,
but they will share much of the features. Remove some of the explicit
references and compatibility checks with 1682M, and replace most of them
with the more generic term "PWRficient".
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NMichael Buesch <mb@bu3sch.de>
Acked-by: NDoug Thompson <dougthompson@xmission.com>

Due to an erratum, we don't want to reset the mpic at boot time. It can
sometimes cause problems with lost interrupts later on while running.
Signed-off-by: NOlof Johansson <olof@lixom.net>

Driver for the CompactFlash slot on the PA Semi Electra eval board. It's
a simple device sitting on localbus, with interrupts and detect/voltage
control over GPIO.

The driver is implemented as an of_platform driver, and adds localbus
as a bus being probed by the of_platform framework.

[akpm@linux-foundation.org: cleanups]
[olof@lixom.net: fix build]
Signed-off-by: NOlof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Milton Miller <miltonm@bga.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move pasemi_idle_init() to be a late_initcall instead of being called from
setup_arch().  This way the cpufreq driver has a chance to initialize and
save away the boot time astate before we go to idle for the first time.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add printout of some SoC error status registers, and dump the SLB contents
for those machine check events where it makes sense.

Since we can't go about and ioremap registers at machine check time,
and we generally want to do as little as possible to print out the
information, pre-build a table of the registers to dump and their address
in the common PCI config space range.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Rework timebase handoff to play nice with configurations with more than
2 cores, as well as with CPU hotplug.

Previous scheme just pushed out the current timebase from the giving
core to all cores without caring if they wanted it or not, nor checking
if they'd taken it. The taking side didn't make sure the giving side
had provided a value yet either. In other words, it was completely broken.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Rename the pasemi platform to "pasemi" to be in line with the
platform's directory name.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Fixes for ethernet IRQ mapping, to be done in the driver instead of in
the platform setup code.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

for consistency with other Open Firmware interfaces (and Sparc).

This is just a straight replacement.

This leaves the compatibility define in place.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Only publish of_platform devices if running on a machine that has them.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

check_legacy_ioport makes only sense on PREP, CHRP and pSeries.
They may have an isa node with PS/2, parport, floppy and serial ports.

Remove the check_legacy_ioport call from ppc_md, it's not needed
anymore.  Hardware capabilities come from the device-tree.
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

arch/powerpc/platforms/pasemi/setup.c: In function 'pasemi_publish_devices':
arch/powerpc/platforms/pasemi/setup.c:220: warning: implicit declaration of function 'of_platform_bus_probe'
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

MDIO driver for PHY's connected via GPIO as on the PA Semi Electra
eval board.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Reset MPIC on boot to clear some timer state that firmware might
leave configured.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is more consistent and gets us closer to the Sparc code.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

I/O TLB support for PA6T-1682M.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The DMA controller on PWRficient is somewhat special -- has a PCI header
so it looks like it's on the root PCI (-Express) root bus, but it uses
more than the default number of interrupts (and they are hardwired).

We need to wire up all interrupts for the DMA controller. The generic
IRQ code will only map the primary interrupt from the PCI header (128),
so add 129->211 by hand.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Timebase update is simple on PA6T, since global updates can be done from
one core by writing to an SPR.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Implement reset on platforms/pasemi. Default is just to reset the
cpu using the SDC registers.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Powersave support on PA6T. Right now it only uses 'doze' mode, and
will default to no savings (spin).
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Print out decoded machine check information on PA6T.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Allow more than the default 256 MPIC sources. Allocates a new flag
(MPIC_LARGE_VECTORS) to be used by platform code when instantiating
the mpic.

I picked 11 bits worth right now since it would cover the number of
sources on any hardware I have seen. It can always be increased later
if needed.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The (maple|pasemi)_init_IRQ functions call of_node_put(root) once more
than they should, causing the refcount of the root node to underflow,
which triggers the WARN_ON in kref_get.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch completely refactors DMA operations for 64 bits powerpc. 32 bits
is untouched for now.

We use the new dev_archdata structure to add the dma operations pointer
and associated data to struct device. While at it, we also add the OF node
pointer and numa node. In the future, we might want to look into merging
that with pci_dn as well.

The old vio, pci-iommu and pci-direct DMA ops are gone. They are now replaced
by a set of generic iommu and direct DMA ops (non PCI specific) that can be
used by bus types. The toplevel implementation is now inline.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch reworks the way IRQs are fixed up on PCI for arch powerpc.

It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().

It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.

I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.

I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

kbuild explicitly includes this at build time.
Signed-off-by: NDave Jones <davej@redhat.com>

Base patch for PA6T and PA6T-1682M. This introduces the
arch/powerpc/platform/pasemi directory, together with basic
implementations for various setup.

Much of this was based on other platform code, i.e. Maple, etc.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>