Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
接近 2 年 前同步成功

通知 170
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 29 4月, 2014 1 次提交
    • S
      RDMA/cxgb4: Fix endpoint mutex deadlocks · cc18b939
      由 Steve Wise 提交于 
      In cases where the cm calls c4iw_modify_rc_qp() with the endpoint
mutex held, they must be called with internal == 1.  rx_data() and
process_mpa_reply() are not doing this.  This causes a deadlock
because c4iw_modify_rc_qp() might call c4iw_ep_disconnect() in some
!internal cases, and c4iw_ep_disconnect() acquires the endpoint mutex.
The design was intended to only do the disconnect for !internal calls.

Change rx_data(), FPDU_MODE case, to call c4iw_modify_rc_qp() with
internal == 1, and then disconnect only after releasing the mutex.

Change process_mpa_reply() to call c4iw_modify_rc_qp(TERMINATE) with
internal == 1 and set a new attr flag telling it to send a TERMINATE
message.  Previously this was implied by !internal.

Change process_mpa_reply() to return whether the caller should
disconnect after releasing the endpoint mutex.  Now rx_data() will do
the disconnect in the cases where process_mpa_reply() wants to
disconnect after the TERMINATE is sent.

Change c4iw_modify_rc_qp() RTS->TERM to only disconnect if !internal,
and to send a TERMINATE message if attrs->send_term is 1.

Change abort_connection() to not aquire the ep mutex for setting the
state, and make all calls to abort_connection() do so with the mutex
held.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>
      cc18b939
  3. 12 4月, 2014 10 次提交
  5. 02 4月, 2014 4 次提交
  7. 29 3月, 2014 1 次提交
  9. 25 3月, 2014 5 次提交
  11. 21 3月, 2014 9 次提交
  13. 15 3月, 2014 2 次提交
    • S
      cxgb4/iw_cxgb4: Doorbell Drop Avoidance Bug Fixes · 05eb2389
      由 Steve Wise 提交于 
      The current logic suffers from a slow response time to disable user DB
usage, and also fails to avoid DB FIFO drops under heavy load. This commit
fixes these deficiencies and makes the avoidance logic more optimal.
This is done by more efficiently notifying the ULDs of potential DB
problems, and implements a smoother flow control algorithm in iw_cxgb4,
which is the ULD that puts the most load on the DB fifo.

Design:

cxgb4:

Direct ULD callback from the DB FULL/DROP interrupt handler.  This allows
the ULD to stop doing user DB writes as quickly as possible.

While user DB usage is disabled, the LLD will accumulate DB write events
for its queues.  Then once DB usage is reenabled, a single DB write is
done for each queue with its accumulated write count.  This reduces the
load put on the DB fifo when reenabling.

iw_cxgb4:

Instead of marking each qp to indicate DB writes are disabled, we create
a device-global status page that each user process maps.  This allows
iw_cxgb4 to only set this single bit to disable all DB writes for all
user QPs vs traversing the idr of all the active QPs.  If the libcxgb4
doesn't support this, then we fall back to the old approach of marking
each QP.  Thus we allow the new driver to work with an older libcxgb4.

When the LLD upcalls iw_cxgb4 indicating DB FULL, we disable all DB writes
via the status page and transition the DB state to STOPPED.  As user
processes see that DB writes are disabled, they call into iw_cxgb4
to submit their DB write events.  Since the DB state is in STOPPED,
the QP trying to write gets enqueued on a new DB "flow control" list.
As subsequent DB writes are submitted for this flow controlled QP, the
amount of writes are accumulated for each QP on the flow control list.
So all the user QPs that are actively ringing the DB get put on this
list and the number of writes they request are accumulated.

When the LLD upcalls iw_cxgb4 indicating DB EMPTY, which is in a workq
context, we change the DB state to FLOW_CONTROL, and begin resuming all
the QPs that are on the flow control list.  This logic runs on until
the flow control list is empty or we exit FLOW_CONTROL mode (due to
a DB DROP upcall, for example).  QPs are removed from this list, and
their accumulated DB write counts written to the DB FIFO.  Sets of QPs,
called chunks in the code, are removed at one time. The chunk size is 64.
So 64 QPs are resumed at a time, and before the next chunk is resumed, the
logic waits (blocks) for the DB FIFO to drain.  This prevents resuming to
quickly and overflowing the FIFO.  Once the flow control list is empty,
the db state transitions back to NORMAL and user QPs are again allowed
to write directly to the user DB register.

The algorithm is designed such that if the DB write load is high enough,
then all the DB writes get submitted by the kernel using this flow
controlled approach to avoid DB drops.  As the load lightens though, we
resume to normal DB writes directly by user applications.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      05eb2389
    • S
      cxgb4/iw_cxgb4: Treat CPL_ERR_KEEPALV_NEG_ADVICE as negative advice · 7a2cea2a
      由 Steve Wise 提交于 
      Based on original work by Anand Priyadarshee <anandp@chelsio.com>.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7a2cea2a
  15. 05 3月, 2014 1 次提交
  17. 14 2月, 2014 1 次提交
  19. 23 1月, 2014 1 次提交
  21. 23 12月, 2013 3 次提交
  23. 16 12月, 2013 1 次提交
  25. 09 11月, 2013 1 次提交